StarTech.com SAT2510BU3 Manuel utilisateur
SATA Hard Drive Enclosure
2.5” SuperSpeed USB 3.0 to
SATA Hard Drive Enclosure
SAT2510BU3
Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules.These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.•
Increase the separation between the equipment and receiver.•
Connect the equipment into an outlet on a circuit different from that to which the receiver•
is connected.
Consult the dealer or an experienced radio/TV technician for help.•
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do
not represent an endorsement of a product or service by StarTech.com, or an endorsement
of the product(s) to which this manual applies by the third-party company in question.
Regardless of any direct acknowledgement elsewhere in the body of this document,
StarTech.com hereby acknowledges that all trademarks, registered trademarks, service
marks, and other protected names and/or symbols contained in this manual and related
documents are the property of their respective holders.
i
Table of Contents
Introduction..................................................................... 1
Packaging Contents.....................................................................1
System Requirements .................................................................1
Installation....................................................................... 2
Hardware Installation...................................................................2
Driver Installation.........................................................................3
Verifying Installation.....................................................................3
Using the Enclosure ....................................................... 4
Specifications.................................................................. 6
Technical Support........................................................... 7
Warranty Information...................................................... 7
1
Introduction
This StarTech.com SuperSpeed USB 3.0 2.5” enclosure lets you connect
a standard 2.5” SATA hard drive through USB 3.0. Supporting data
transfer rates of up to 5 Gbps, this external HDD enclosure delivers
access to files at lightning fast speeds - 10x that of USB 2.0, and 60%
faster than eSATA (SATA revision 2). Backward compatible with USB
revisions 2.0 and 1.1 at speeds of 480Mbps and 12 Mbps respectively,
so the enclosure can be used with older systems that don’t support the
newest USB standard.
Packaging Contents
1 x SAT2510BU3 enclosure•
1 x USB 3.0 micro-B to A “Y” cable•
1 x Package of screws•
1 x Screw Driver•
1 x Carrying Pouch•
1 x Instruction Manual•
System Requirements
USB enabled computer system with available port•
2.5” SATA hard drive (9.5mm height only) with 7+15 SATA connector•
Microsoft• ®Windows®2000/XP/Server 2003/Vista/Server 2008 R2/7
(32/64-bit), or Apple®Mac OS®10.5/10.6, or Linux®
2
USB 3.0 micro-B
connector
Power/Activity
LED
Installation
WARNING: Hard drives require careful handling, especially when being
transported. If you are not careful with your hard disk, lost data may
result. Always handle your hard drive and storage device with caution.
Hardware Installation
Slide both the top and bottom covers of the enclosure off to reveal the1.
plastic frame of the enclosure.
Place a 2.5” SATA hard drive into the tray by angling the hard drive2.
towards the SATA hard drive connector on the circuit board. Slide the
hard drive into the connector and then lower the opposite end into the
tray.
Using the provided screws, fasten the hard drive to the frame of the3.
enclosure from the bottom side.
Place both the top and bottom covers back onto the enclosure, making4.
sure to line up the screw holes on the covers with the screw holes on
the side of the enclosure. Use the provided screws to fasten the covers
to the frame.
3
Using the provided USB 3.0 micro-B cable, connect the enclosure to5.
an available USB port on the computer system. This cable can be
connected to any type of USB type A port, not just USB 3.0 ports.
NOTE: A USB 2.0 micro-B cable can also be substituted for the USB3.0
cable, but will not allow for USB 3.0 speeds, if connected to a USB 3.0
port.
NOTE: Only the Primary connector is required
to be plugged into the computer system. The
Secondary connector may be required if the hard
drive cannot draw enough power from a single
port (i.e. USB 2.0 ports).
Driver Installation
No driver installation is required for these operating systems, as this
enclosure is natively supported, so the drivers are already installed.
Verifying Installation
Windows 2000/XP/Server 2003/Vista/7
From the main desktop, right-click on “My Computer” (“Computer” in
Vista/7), then select Manage. In the new Computer Management window,
select Device Manager from the left window panel.
4
Double-click on the “Disk Drives” option. A new disk drive should be listed
under this category. It will typically contain the make/model of the hard
drive you have installed in the enclosure.
Using the Enclosure
Windows 2000/XP/Vista/7
If you are using a brand new hard drive that does not contain any data,
then you will first need to prepare the hard drive for use. From the main
desktop, right-click on “My Computer” (“Computer” in Vista/7), then
select Manage. In the new Computer Management window, select Disk
Management from the left window panel.
Locate the Disk that says it is “Unallocated” (check hard drive capacity to
confirm it’s the correct hard drive) and then right-click in the section that
says “Unallocated” and select “New Partition”.
5
The New Partition Wizard will appear. Follow the instructions in the
wizard to complete setting up the drive. Once complete, the Disk should
show up as “Healthy” with a drive letter assigned (i.e. E:). This drive letter
should now appear within My Computer.
If you are installing a hard drive that already has data on it, then after
plugging it in, the drive should automatically show up with a drive letter
assigned within My Computer.
6
Specications
Bus Interface USB revision 3.0
Chipset ID ASMedia ASM1051
Connectors 1 x USB3.0 micro-B
LEDs 1 x Power/Activity
Compatible Hard Drives 2.5” SATA hard disk/solid state
drives, 9.5mm height
Maximum Data Transfer Rate USB 3.0: 5Gbps
Power Adapter None
Operating Temperature 0°C ~ 60°C (32°F ~ 140°F)
Storage Temperature -20°C ~ 70°C (-4°F ~ 158°F)
Humidity 10 ~ 90% RH
Dimensions 113.0mm x 76.0mm x 14.0mm
Weight 63.5g
Compatible Operating
Systems
Windows 2000/XP/Server 2003/
Vista/Server 2008 R2/7 (32/64-
bit), Mac OS 10.5/10.6, Linux
7
Technical Support
StarTech.com’s lifetime technical support is an integral part of our
commitment to provide industry-leading solutions. If you ever need
help with your product, visit www.startech.com/support and access our
comprehensive selection of online tools, documentation, and downloads.
Warranty Information
This product is backed by a one year warranty.
In addition, StarTech.com warrants its products against defects in
materials and workmanship for the periods noted, following the initial date
of purchase. During this period, the products may be returned for repair,
or replacement with equivalent products at our discretion. The warranty
covers parts and labor costs only. StarTech.com does not warrant its
products from defects or damages arising from misuse, abuse, alteration,
or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA
LLP (or their officers, directors, employees or agents) for any damages
(whether direct or indirect, special, punitive, incidental, consequential, or
otherwise), loss of profits, loss of business, or any pecuniary loss, arising
out of or related to the use of the product exceed the actual price paid
for the product. Some states do not allow the exclusion or limitation of
incidental or consequential damages. If such laws apply, the limitations or
exclusions contained in this statement may not apply to you.
Table des matières
Autres manuels StarTech.com Enceinte
StarTech.com
StarTech.com SAT3540U2E Manuel utilisateur
StarTech.com
StarTech.com S3510BMU33 Manuel utilisateur
StarTech.com
StarTech.com S3510BMU33ET Manuel du système
StarTech.com
StarTech.com S3510BMU33T Manuel du système
StarTech.com
StarTech.com S252BU33R Manuel utilisateur
StarTech.com
StarTech.com IEEE-1394b Manuel
StarTech.com
StarTech.com RK616WALM Manuel utilisateur
StarTech.com
StarTech.com M2E1BRU31C Manuel utilisateur
StarTech.com
StarTech.com SAT3510U2V Manuel utilisateur
StarTech.com
StarTech.com S3510SMU33 Manuel du système
StarTech.com
StarTech.com RK920WALM Manuel utilisateur
StarTech.com
StarTech.com UNI3510BMU32 Manuel utilisateur
StarTech.com
StarTech.com SAT2510U2E Manuel utilisateur
StarTech.com
StarTech.com SAT3520UERGB Manuel utilisateur
StarTech.com
StarTech.com RK830WALVS Manuel utilisateur
StarTech.com
StarTech.com HSB320SATBK Manuel utilisateur
StarTech.com
StarTech.com SAT3520U3R Manuel utilisateur
StarTech.com
StarTech.com SAT1810U2 Manuel utilisateur
StarTech.com
StarTech.com IDECASE18U2B Manuel utilisateur
StarTech.com
StarTech.com SAT3510BU2E Manuel utilisateur
