Pulsar ARAD-S4 Manuel utilisateur

Code: ARAD-S4

Name: Security enclosure 4U/400mm/48/17Ah for RACK 19"

cabinets two-level

v1.0

Edition: 1 from 14.06.2017

Supersedes: --------------

1. Intended use:

The metal RACK-Security enclosure is designed for mounting the alarm control panel and the input/output modules in

free-standing RACK19” cabinets with depths in the range from 800 to 1000mm. It consists of two elements:

1. Patch Panel is used to switch between the YTDY 6x0,5 cable with copper cores and the elastic cable supplying

signals and power to the control panel.

2. Pull out enclosure with a 4U height –alarm control panel and input and output modules are mounted in this

section - with a space for 17Ah battery, transformer, and the ARAW45 fan (transformer and fan are not included).

Both ARAS800 and ARAS1000 rails - selected depending on the depth of a RACK cabinet - constitute the load

bearing part of the enclosure (not included). The enclosure is fitted with 6 printed circuit boards (PCB) allowing connection

of signal, power and control cables. Each of the boards has 8 pairs of terminals designed to operate at a voltage of 30VDC

and a maximum current of 1,5A In addition, each one is fitted with the 230VAC power board. The enclosure is fitted with 3

tamper switches:

1. Pulling out the enclosure from RACK profiles

2. Enclosure opening

3. Patch Panel opening

Universal holes in the enclosure allow mounting of control panels and expansion modules of the following companies:

DSC, PARADOX, RISCO, SATEL, PYRONIX, CROW, ROGER.

Fig.1

2. Mounting of the ARAS800/1000 rail in the RACK 19” cabinet:

Mount cage nuts for M6 screws in the RACK cabinet, as shown in Figure 2 below, and mount the ARAS rails

(depending on the depth of a RACK cabinet). Make sure that the rail is correctly mounted horizontally and its length

between the front and rear RACK profile is properly adjusted.

Fig.2

3. Mounting of the ARAD-S4 in the RACK 19” cabinet:

After mounting the ARAS rails in the rear of the RACK 19 ", mount the Patch Panel as shown in Figure 3.

Fig.3

Mount the ARAD-S4 enclosure on fully extended ARAS rails using 6xM4 screws (complete with ARAS rails).

Tighten the screws from the inside. Connect the Patch Panel wires as shown in the Fig.4

CAUTION!!! - Pay attention to the correct arrangement of A / B / C / D / E / and F connectors

in the appropriate sockets described on PCB Signal Boards.

Fig.4

Two protective tubes with a length of 0,5 m. are used for routing of power cords and signal cables from the

installation to the Patch Panel. Protective tube for power cord –internal/external diameter ø6/ø10 (available as

accessory –MM064). Protective tube for signal cables –24 YTDY 6x0.5 wires, internal/external diameter ø21/ø29

(available as accessory –MM020). The routing of protective tubes in the Patch Panel and its sealing is shown in the Fig. 5.

Fig. 5

The ARAD-S4 enclosure is fitted with 3 tamper switches:

1. Pulling out the enclosure from RACK profiles

2. Enclosure opening

3. Patch Panel opening

The enclosure is mounted in the front of the RACK rails - using 4xM6 screws.

The Patch Panel is mounted in the rear of the RACK rails - using 6xM6 screws + patch panel cover plate 4xM6

4. PCB boards - mounting:

PCB supply: 230VAC/max. 5A

PCB Power Board in the Patch Panel PCB Power Board in a retractable housing

PCB Signal Boards. Single PCB Signal Board allows connecting up to 8 signal/supply lines. The maximum operating

conditions of a single line –30VDC/1,5A.

PCB Signal Board in the Patch Panel PCB Signal Board in a retractable housing

5. Additional equipment:

Space for 17Ah battery /TRP/TRZ 20÷80VA transformer / ARAW45 fan/ 230VAC board with the F3,15A melting fuse

6. Dimensioning

Mounting plate Hinged mounting plate

7. Control panels and modules that can be mounted in the enclosure.

DSC: (PC 1404, 1616, 1832, 1864, 4020, 4204, 4216, 4580, 5400, 5204, 5580, 5200)

+ 5 x 5108 (4108, 5208, 5100, 4116)

PARADOX: (728ULT, E55, E65, SP4000, SP5500, SP6000, SP7000, EVO48, EVO192)

+ 5 x ZX8 ( ZX4, PGM4, APR3 - HUB2)

RISCO: (PRO24, PRO116, PRO128, PRO140)

+ 5 x EZ04 (EZ8, EZ16, RP296EPS)

SATEL: (CA4V1, CA5, CA6, CA10, VERSA5, 10, 15, INTEGRA24, 32, 64, 128, CA64 PTSA, CA64 PP)

+5x CA64E(CA10E, PP, EPS, ADR, O-R, O-ROC, O-OC,OPS- OC, OPS- R, OPS- ROC, VGM- 16, SR, PTSA)

PYRONIX: MATRIX 424, 832, 832+

TEXECOM: PREMIER412, 816, 832, 48, 88,168, 640

TELMOR: TCA-824 + 5 x TEX800 (TMT1)

ROGER: PR402, CPR 32- SE

EBS: PX 202A

PULSAR: 5x (MS1012, MSR1012, MSRK1012)

5x (MS2012, MSR2012, MSRK2012)

ROEL: SIGMA6 / SIGMA8 / CERBER

CROW: RUNNER 4/8

8. Technical parameters

Battery compartment

17Ah / 12V

Transformer compartment

TRP: 20÷80VA, TRZ: 20÷80VA

Tamper protection:

- Pulling out the enclosure from RACK

profiles

- Enclosure opening

- Patch Panel opening

the C/NO terminals (C/NC closed housing), 1A@30VDC/3A@250VAC

the C/NO terminals (C/NC closed housing), 0,5A@30VDC/50VAC

PCB Signal Boards

Level I:

A/B Board –8 signal lines - 30VDC/1,5A –1 pair

C/D Board –8 signal lines - 30VDC/1,5A –1 pair

E/F Board –8 signal lines - 30VDC/1,5A –1 pair

Level II:

A/B Board –8 signal lines - 30VDC/1,5A –1 pair

C/D Board –8 signal lines - 30VDC/1,5A –1 pair

E/F Board –8 signal lines - 30VDC/1,5A –1 pair

PCB Power Board

230VAC/max.5A

Mounting dimensions:

W=19", H=4U

Enclosure dimensions

W=395, H=159, D=400 mm

Net/gross weight:

14 / 15 [kg]

Finish:

- steel plate 1 / 1,5mm, color black (RAL 9004)

Application:

Indoor

Notes:

- The enclosure is mounted using the ARAS800/1000 rails

depending on the depth of the RACK 19" cabinet + 4xM6 screws butt

mounted to RACK profiles

- Patch Panel mounting –8xM6 butt mounted to RACK profiles + 2xM6

to ARAS800/1000 rails

- The set includes:

protective tube MM020 ø21/ø29 – 0,5m –2 pieces

protective tube MM064 ø6/ø10 –0,5m –1 pcs.

cable tie (black) 100x2,5 –18 pieces

cable tie (black) 190x4,8 –6 pieces

12 M6 screws+ cage nuts + plastic washer

2 M6 screws + plastic washer

Available accessories:

- MM020 - protective tube ø21/ø29 – signal wires

- MM064 - protective tube ø6/ø10 – for power cord

- ARAW45 - fan

- AWZ618 - 230VAC board with the F3,15A melting fuse

- transformers of the TRP/TRZ series: 20÷80VA

Declarations, warranty

CE, RoHS, 2 years from the production date

PRODUCENT

Pulsar

Siedlec 150, 32-744 Łapczyca

Tel. (+48) 14-610-19-40, Fax. ( +48) 14-610-19-50

e-mail: [email protected], [email protected]

http:// www.pulsar.pl, www.zasilacze.pl

Autres manuels Pulsar Enceinte

Pulsar

Pulsar AWO 500PU Manuel utilisateur

Pulsar

Pulsar 17/EIZ75/SATEL/G3 Manuel utilisateur

Pulsar

Pulsar 17/TRP40/RISCO Manuel utilisateur

Pulsar

Pulsar AWO 256 Manuel utilisateur

Pulsar

Pulsar AWO 151 Manuel utilisateur

Pulsar

Pulsar AWO 200PU Manuel utilisateur

Pulsar

Pulsar 7/TRP20/GSM Manuel utilisateur

Pulsar

Pulsar 17/50/DSPR/PUSTA Manuel utilisateur

Pulsar

Pulsar ARAD4 Manuel utilisateur

Pulsar

Pulsar RAKU3 Manuel utilisateur

Pulsar

Pulsar AWO529 Manuel utilisateur

Pulsar

Pulsar AWO 220PU Manuel utilisateur

Pulsar

Pulsar DIN1 Manuel utilisateur

Pulsar

Pulsar AWO 359 Manuel utilisateur

Pulsar

Pulsar AWO385 Manuel utilisateur

Pulsar

Pulsar AWO 350 Manuel utilisateur

Pulsar

Pulsar AWO 417 Manuel utilisateur

Pulsar

Pulsar AWO-256 Manuel utilisateur

Pulsar

Pulsar AWO530 Manuel utilisateur

Pulsar

Pulsar AWO454 Manuel utilisateur

Pulsar

Pulsar AWO 620 Manuel utilisateur

Pulsar

Pulsar DIN3/Plate/RACK 19 Manuel utilisateur

Pulsar

Pulsar AWO 350 Manuel utilisateur

Pulsar

Pulsar AWO224 Manuel utilisateur

Manuels Enceinte populaires d'autres marques

SilentiumPC

SilentiumPC Armis AR5 Manuel

Thermaltake

Thermaltake V150 TG Manuel utilisateur

MSI

MSI MPG SEKIRA 500X Manuel utilisateur

Antec

Antec Dark fleet DF-10 Manuel utilisateur

Nexans

Nexans WTC05 Manuel utilisateur

Peavey

Peavey DS 1502 Manuel utilisateur

D-Link

D-Link ShareCenter Pro DNS-1550-04 Manuel utilisateur

Rosewill

Rosewill RX82-U(JBOD) Manuel utilisateur

QNAP

QNAP SAS JBOD CLI 1.0 Manuel utilisateur

GAMDIAS

GAMDIAS Talos P1 Manuel utilisateur

Auvs

Auvs KR615 Manuel utilisateur

Digitus

Digitus DA-71114 Manuel utilisateur

CommScope

CommScope FDH 3000 Manuel utilisateur

FS FHD-FWME4 Manuel utilisateur

JBL

JBL CS1215T Manuel utilisateur

NewerTech

NewerTech Voyager S3 Manuel utilisateur

Savio

Savio ARMOR X1 Manuel utilisateur

Alfa Network

Alfa Network AWAP02O Manuel utilisateur