Star Micronics SLIP SP298 SERIES Manuel d'utilisation et d'entretien

SLIP PRINTER

SP298 SERIES

Programmer’s Manual

Trademark acknowledgments

SP298

: Star Micronics Co. Ltd.

ESC/POS, TM-295, TM-290

: Seiko Epson Corporation

Notice

mission, is strictly forbidden.

• The contents of this manual are subject to change without notice.

• All efforts have been made to ensure the accuracy of the contents of this manual at the time of printing. However,

should any errors be found, STAR would greatly appreciate being informed of them.

• The above notwithstanding, STAR can assume no responsibility for any errors in this manual.



TABLE OF CONTENTS

Chapter 1: DIP Switch Settings ................................................................. 1

Accessing the DIP switches ....................................................... 1

Available DIP switch settings (Serial Interface) ........................ 3

Available DIP switch settings (Parallel Interface) ..................... 4

Chapter 2: Memory Switch Settings.......................................................... 5

Chapter 3: Control Panel Operations ....................................................... 6

Indicator lights ........................................................................... 6

Buttons ....................................................................................... 7

Producing a test print ................................................................. 7

Adjusting the dot alignment ....................................................... 7

Hexadecimal dump .................................................................... 9

Errors ....................................................................................... 10

Chapter 4: Interface .................................................................................. 11

Serial Interface ......................................................................... 11

Serial interface pins and signal names ..................................... 12

Pins and Signal Names ............................................................ 12

Interface connections ............................................................... 13

Data protocol ............................................................................ 14

Parallel Interface ...................................................................... 17

Connectors and Signals ............................................................ 17

Chapter 5: Peripheral Unit Driver Circuit ............................................. 19

Modular plug ............................................................................ 19

Drive circuit ............................................................................. 20

Chapter 6: Control Codes ......................................................................... 21

Star Mode Commands ............................................................. 21

ESC/POS Mode Commands (TM-295 emulation) .................. 26

ESC/POS Mode Commands (TM-290 emulation) .................. 28

TM-295 mode emulation cautionary items .............................. 60

Appendix: Character Code Tables ............................................................ 62

Please access the following URL

http://www.star-micronics.co.jp/service/sp_sup_e.htm

for the lastest revision of the manual.

Chapter 1: DIP Switch Settings

The printer’s DIP switches let you change communications parameters, input

buffer size, and emulation. This chapter explains the settings you can make and

tells you how to actually change DIP switch settings.

Accessing the DIP switches

The DIP switches are located inside the printer, underneath the document table.

Use the following procedure to remove the document table so you can operate

the DIP switches.

❏

Make sure that the printer is turned off and unplugged from its wall outlet.

❏

Remove the printer cover.

❏

While using a screwdriver or other similar instrument to press down at the

location marked (a) in the illustration below, carefully slide the document

table in the direction indicated by the arrow until it is out of the way.

It is not necessary to remove the document table completely, just move it

enough so you can get at the DIP switches inside.

Note:

If the document table seems to be getting caught on the rollers, it means that

you are not pressing down at point (a) enough. Pressing at point (a) should

separate the rollers to the document table can slide freely.

❏

After the document table is opened sufﬁciently, use a thin ﬂat-blade

screwdriver or some other similar object to change DIP switch settings.

Note:

See the following section for details on available DIP switch settings.

❏

After making the settings you want, slide the document table back into

place while pressing down at point (a). Make sure that the document table

is correctly seated in place before releasing point (a).

❏

Replace the printer cover.

OFF

OFF 12345678

(For Serial Interface)

(For Parallel Interface)

OFF 12345678910

Available DIP switch settings (Serial Interface)

The following table shows all the possible settings for the DIP switch. The

factory default settings are ON for switches 1 through 7 and OFF for switches

8 through 10.

*1: Never set switch 7 to OFF at the same time that switch 8 is set to ON.

Switch Parameter ON OFF

1Baud Rate See table below.

3 Data Length 8 bits 7 bits

4 Parity Check Disabled Enabled

5 Parity Odd Even

6 Handshake DTR/DSR XON/XOFF

7Command Emulation See table below.

9 Pin 6 (DSR) Reset Signal Enabled Disabled

10 Pin 25 (INIT) Reset Signal Enabled Disabled

Baud Rate Switch 1 Switch 2

1200BPS OFF OFF

2400BPS ON OFF

4800BPS OFF ON

9600BPS ON ON

Command Emulation Switch 7 Switch 8

Star mode ON ON

ESC/POS (TM-295) ON OFF

ESC/POS (TM-290) OFF OFF

Not used (*1) OFF ON

Available DIP switch settings (Parallel Interface)

The following table shows all the possible settings for the DIP switch. The

factory default settings are ON for switches 1 through 7 and OFF for switch 8.

A reset can be performed with pin 31 on the interface by setting DIP switch 1 to

ON (the factory default setting).

In addition, when a reset can be performed with pin 31, setting DIP switch 2 to

OFF sets up the unit to perform a reset when pin 31 and pin 36 are “LOW”.

*1: Never set switch 7 to OFF at the same time that switch 8 is set to ON.

Switch Parameter ON OFF

1Pin 31 / Pin 36 Reset Signal See table below.

Not used (Always ON)

7Command Emulation See table below.

Reset Signal Switch 1 Switch 2

Pin 31 is enabled. ON ON

Pin 31/Pin 36 are enabled. ON OFF

Disabled OFF ON

Disabled OFF OFF

Command Emulation Switch 7 Switch 8

Star mode ON ON

ESC/POS (TM-295) ON OFF

ESC/POS (TM-290) OFF OFF

Not used (*1) OFF ON

Chapter 2: Memory Switch Settings

Each memory switch is a 16-bit word store in EEPROM. For details on the

functions and settings of memory switches, refer to “Chapter 6”.

The table below shows the factory settings for the memory switches.

Warning!

Changing the memory switch settings can cause the printer to fail to operate

correctly.

Memory Switch Hexadecimal Code

0 0000

1 0000

2 0000

3 0000

4 0000

5 0000

Chapter 3: Control Panel Operations

The control panel gives you some push-button control over the slip printer

operation. It also includes indicator lights, which tell you the current status of

the printer at a glance.

Indicator lights

The following table describes the meaning of indicator lights when it is on, off,

or flashing.

Indicator Light Off On Flashing

POWER

Power off Power on Dot Alignment Adjust

Mode

PAPER OUT

Paper inserted No paper Insert paper prompt

RELEASE

Slip paper engaged Slip paper released Mechanical error

FORWARD

POWER

RELEASE

PAPER

OUT REVERSE

RELEASE

Buttons

The following table describes the function of the three control buttons of the

control panel.

Producing a test print

The following procedure can be used at any time to test the printer.

❏

Turn on the printer and insert a piece of paper (page 6, 11).

❏

Turn off printer power.

❏

While holding down

RELEASE

, turn printer back on. Keep

RELEASE

depressed for a few moments until the printer beeps and the printer test

print starts.

The printer test will continue until it reaches the end of the paper.

Adjusting the dot alignment

You may never have to use the procedure described in this section, but after you

have been using your printer for some time you may find that the dots of some

graphics do not align correctly. For example, what should look like:

may come out looking like one of the following:

Button Description

FORWARD

Feeds the slip paper forward, toward the back of the printer. One press

feeds one line, holding down performs continuous feed.

REVERSE

Feeds the slip paper back, toward the front of the printer. One press

feeds one line, holding down performs continuous feed.

RELEASE

Activates the printer's paper release (the paper is not held in place by

the paper feed roller).

Clears recoverable errors.

or like this

Autres manuels pour SLIP SP298 SERIES

Table des matières

Autres manuels Star Micronics Imprimante

Star Micronics

Star Micronics TSP700II Series Manuel utilisateur

Star Micronics

Star Micronics 4111 Instructions d'utilisation

Star Micronics

Star Micronics FVP-10U Manuel utilisateur

Star Micronics

Star Micronics TSP700 Series Instructions d'installation

Star Micronics

Star Micronics gemini-10X Manuel utilisateur

Star Micronics

Star Micronics TSP650II SERIES Manuel utilisateur

Star Micronics

Star Micronics NP-215 Manuel utilisateur

Star Micronics

Star Micronics NP-226 Instructions d'installation

Star Micronics

Star Micronics SM-T300I SERIES Manuel utilisateur

Star Micronics

Star Micronics TUP900 Series Manuel utilisateur

Star Micronics

Star Micronics LS-5 SERIES Manuel utilisateur

Star Micronics

Star Micronics TSP400 Series Manuel utilisateur

Star Micronics

Star Micronics SLIP SP298 SERIES Manuel utilisateur

Star Micronics

Star Micronics TSP200 Series Manuel utilisateur

Star Micronics

Star Micronics 10X Manuel utilisateur

Star Micronics

Star Micronics NX-1500 Manuel utilisateur

Star Micronics

Star Micronics SP 200 Manuel utilisateur

Star Micronics

Star Micronics NR-10 Manuel utilisateur

Star Micronics

Star Micronics MULTI-FONT NX-1000II Manuel utilisateur

Star Micronics

Star Micronics SLIP SP298 SERIES Manuel utilisateur

Star Micronics

Star Micronics NX-10 Manuel utilisateur

Star Micronics

Star Micronics TSP800 Series Manuel utilisateur

Star Micronics

Star Micronics Star DP8340 Manuel utilisateur

Star Micronics

Star Micronics LaserPrinter4 Manuel utilisateur

Manuels Imprimante populaires d'autres marques

Lexmark

Lexmark 1400 Series Manuel

Canon

Canon i70 Series Manuel utilisateur

Evolis

Evolis Elypso Manuel utilisateur

Kyocera

Kyocera FS-9530DN Manuel utilisateur

Canon

Canon LASER SHOT LBP-1210 Manuel utilisateur

Samsung

Samsung BIXOLON SRP-350plusF Manuel utilisateur

Canon

Canon PIXMA PRO-1 Series Manuel utilisateur

Canon

Canon PIXMA G3560 Guide de configuration

Dell

Dell Color Laser Printer 2130cn Manuel utilisateur

Tektronix

Tektronix Phaser 840 Manuel utilisateur

Epson

Epson ET-7750 Mode d'emploi

Canon

Canon CLBR 460ps Manuel utilisateur

Eltron

Eltron P210 Guide Manuel utilisateur

Ricoh

Ricoh MD-P1 Manuel utilisateur

Epson

Epson SC-F7100 series Manuel utilisateur

Epson

Epson Stylus C40UX Manuel utilisateur

Canon

Canon imagePASS-A2 Manuel utilisateur

Canon

Canon S820D Manuel utilisateur