Star Micronics NP-215 Manuel utilisateur

Spec. No D-F0301

Specifications for

Kiosk module printer

NP-215

NP-225

NP-325

NP-415W

Revision 1.00 2000.08.01 1 edition

Revision 2.00 2001.04.18 2 edition

Revision 2.10 2001.06.13 3 edition

Revision 2.20 2002.01.29 4 edition

Revision 2.30 2002.02.15 5 edition

Revision 2.40 2002.03.26 6 edition

Revision 2.50 2002.04.12 7 edition

Revision 2.60 2002.07.09 8 edition

Revision 2.70 2003.01.31 9 edition

《Notice》･All features and specifications described are subject to change without notice.

Read carefully Before Using the Printer

Wrong handling of the printer may cause its performance declined and the product damaged. Please

read the notes below before handling.

1. Static discharge prevention must be made for installation and removal of the printer to protect IC

and other electrical parts. Connect it to the earth ground. It is also requested to remove the static

from body of the person before handling, especially, the input terminal.

2. Avoid excessive force to the input terminal for handling.

3. When any type of paper, other than specified in this manual, is used, it may cause deterioration

of the print quality and thermal head reliability.

Examples of troubles

1) Print quality deterioration by using low sensitivity paper.

2) Thermal head wears due to roughness of paper surface.

3) Sticking between heat receipt layer and thermal head, and vibration noise during printing.

4) Print ink disappears on low print durability paper.

5) Electrolyte corrosion on thermal head due to low quality of heat receipt layer.

4. Avoid printing with no paper loaded. It damages platen and thermal head.

5. Do not scrabble thermal head with sharp edge or something hard, or give impact. The heat

element may be damaged.

6. Set the power of printer off before connecting or removing connecters.

7. When printing in high speed under low temperature of high humidity environment, the paper may

be stained by moisture that appears from paper, or the printer may have condensation. Avoid

dew from dropping down to the thermal head that may cause electrolyte corrosion. Turn the

power off until any dew is removed.

8. The printer is not protected from water or dew formed. Do not water the printer or handle it with a

wet hand, which may cause damage to the printer due to short circuit, or heat or fire.

9. The printer is not protected from dust or dirt. If it is used at dusty place, the thermal head may be

damaged or paper feed is not operated properly.

10. When cleaning the printer with a vacuum cleaner, avoid the printer’s paper outlet from locating

cleaner’s air inlet.

11. The printer’s main structure parts use plated steel. However, rust may be caused to the cut

section.

12. Reflection type of infrared ray sensors are used at some locations in the printer. Direct sun light

may cause mal-function of printer. Avoid from such a location for installation.

13. This printer does not support any operations caused by the commands or control commands not

specified in this manual.

Table of Contents

1. Overview

1.1 Overview 1

1.2 Features 1

1.3 Configuration 2

2. Specifications

2.1 Basic specifications 2

2.2 Printing area and cutter position 4

2.3 Power supply specifications 5

2.4 Reliability 5

2.5 Dimensions

1) NP-215 dimensional drawing 6

2) NP-225 dimensional drawing 7

3) NP-325 dimensional drawing 8

4) NP-415W dimensional drawing 9

3. Interface specifications

3.1 Parallel interface (Centronics) 10

3.2 Serial interface (RS-232C) 11

3.3 Connector connections 12

3.4 Connector signal details 12

4. Functions

4.1 Function setting 16

4.2 Processing error 17

4.3 Buffer full print 17

4.4 Automatic paper cut 18

4.5 Winder drive 18

4.6 Partition drive 18

5. Control commands

5.1 Control command table 19

5.2 Printer driver 20

5.3 Control command details 20

6. Character code table

6.1 Domestic code table 39

6.2 Overseas character code table 40

6.3 International character code table 41

7. Cable

7.1 B501 power cable 42

1. Overview

1.1 Overview

The printer is categorized as following.

NP - * * 5 * *

1 2 3 4

1: Paper width, 2 = 2 inches, 3 = 3 inches

2: Paper setting, 1= Paper holder type, 2 = Drop-in type

3: Interface, P = Parallel, R = Serial, D = Parallel/Serial compatible

4: OEM number

* D type is parallel and serial compatible. Interface connector is not incorporated.

NP - 4 1 5 W * *

1 2 3

1: Windows driver available

2: Interface, P = Parallel, R = Serial, D = Parallel/Serial compatible

3: OEM number

* D type is parallel and serial compatible. Interface connector is not incorporated.

1.2 Features

This module printer is designed on the basis of our long experience as a printer manufacturer.

Individual unit such as printer mechanism, controller board and auto-cutter is assembled in

compact with our reliable design concept.

Simple integration to the system requiring only power and data supplies, that contributes to the

short development time and improvement of product reliability.

1) Important areas such as paper entrance and auto-cutter guide are designed professionally on

the basis of our long experience as a printer manufacturer.

2) Small, compact and light weight. Easy to integrate into various kinds of system.

3) Short development time.

4) High speed and quality of printing

5) Both parallel and serial interfaces are available as a standard.

6) Various barcode symbols, 1-D and 2-D (QR code) are available.

7) Various kinds of application are available.

8) Possible to control paper presenter (paper transfer and present device).

9) User-friendly drop-in type of roll paper holder with paper end sensor. * 1

10) Windows drivers (Windows95/98/NT4.0/2000) are available.

11) Easy to write/rewrite F/W by using flash memory. Also, 3 patterns of registration are

available with NV bit image.

*1 Drop-in type of paper holder is for NP-225, NP-325 and NP-415W. NP-215 is paper holder

type.

1.3 Configuration

The printer consists of the following components.

Product Name

Description Specification Part No. Q’ty

NP-215 NP-225 NP-325 NP-415W

NP-215 1 X

NP-225 1 X

NP-325 1 X

Printer

NP-415W 1 X

60xØ48mm 24-X117 1 X X

80xØ48mm 24-X121 1 X

Thermal paper

112xØ48mm 24-X116 1 X

80R 35-029Q 1 X

Paper holder 80L 35-030Q 1 X

Screws tight 21-U196 2 X

B501power

cable

D-P44507 30-439A 1 X X X X

*B501 power cable : D type only

2. Specifications

2.1 Basic specifications

No. Specifications NP-215/225 NP-325 NP-415W

1. Print method Line thermal dot ÅÅ

2. Total dots / line 432 dots 576 dots 832 dots

3. Dot density 8 dots / mm ÅÅ

4. Print width 54 mm 72 mm 104 mm

5. Print speed (Max.)

*It can be changed by the

condition.

85 mm / s

1 partition drive

(ASCII print)

70 mm / s

1 partition drive

(ASCII print)

70 mm / s

Automatic partition

drive (ASCII 38 print)

6. Print digits

Font A (12×24)

Font B (9×17)

36 digits (Font A)

48 digits (Font B)

48 digits (Font A)

64 digits (Font B)

69 digits (Font A)

92 digits (Font B)

1 Print specs.

7. Line feed pitch 0.125 mm ÅÅ

1. Character size

Font A (12×24)

Font B (9×17)

1.50×3.00 mm

1.13×2.13 mm

2. Character types

ASCII 224 ÅÅ

Block graphics 80×2 ÅÅ

International 32 ÅÅ

2 Character

specs.

3. Character modification Double width ÅÅ

Vertical double ÅÅ

Quadruple ÅÅ

Bold ÅÅ

Double strike ÅÅ

Inverted ÅÅ

90°clockwise rotation

Black/white reverse

Underline

4. Line spacing (Default) 4.25 mm (1/6 inch) ÅÅ

ANK mode ÅÅ

Bit image mode ÅÅ

3 Print mode

Barcode mode ÅÅ

1-D symbology UPC-A

UPC-E

EAN-13 (JAN-13) ÅÅ

EAN-8 (JAN-8) ÅÅ

CODE39 ÅÅ

4 Barcode

specs

ITF

ÅÅ

CODABAR (NW-7) ÅÅ

CODE128 ÅÅ

2-D symology QR code ÅÅ

Parallel Centronics ÅÅ5 Interface

Serial RS-232C

ÅÅ

6 Auto-cutter 1. Cut method Guillotine type ÅÅ

2. Applicable paper Thermal 65 - 125

(micro)

ÅÅ

3. Cut cycle 30 cuts / minute ÅÅ

4. Cut mode (by command

setting)

Total cut

Partial cut (a 2mm tab

left at the center)

ÅÅ

5. Life time 300,000 cuts ÅÅ

1. Paper width 60 mm 80 mm 112mm

2. Max. diameter Ø80 mm / Ø83 mm Ø83 mm Ø83 mm

3. Core diameter Inner Ø12mm

Outer Ø18mm ←←

7 Paper

specs.

4. Papers recommended TF50KS-E2D (Nihon Seishi)

PD160R-N (Shin Oji Seishi)

AFP235 (Mitsubishi Seishi)

TL69KS-R2 (Nihon Seishi)

TL69KS-HW74 (Nihon Seishi)

TC98KS-T1 (Nihon Seishi)

8 Receiving

buffer

Approx. 10K bytes ←←

9 Operation

ALMLED OUT

Line feed SW input

←

10 Weight Net weight approx. 550g / 650g approx. 750g approx. 1,250g

11 Low sensor Approx. 22.5 Ø (approx.2.5m+-1m. When inner

of paper core is Ø 12 and outer is Ø 18)

Reflection sensor.

Approx. 3m +- 1.5m

(When inner of paper

core is Ø 12 and outer

is Ø 18.) Changeable

reflection sensor

2.2 Printing area and cutter position

Cutter position (Cutting place)

TOP 0.0mm

Cutterposition 3.0mm

Unprintable area

Head position 17.5mm

Sensor position 28.5mm

1 2 D

0.125mm

B C B

9.1+-0.5mm

Black mark printing 5.3+-0.2mm min.

10.3+-0.2 mm min.

NP-215

NP-225 NP-325 NP-415W

A 60mm 80mm 112mm

B 3mm 4mm 4mm

C 54mm 72mm 104mm

D 432dot 576dot 832dot

1. Black mark printing is used

when preprint paper is formatted

and used.

2. Black mark printing is printed on

the backside with black ink.

3. Do not print around the black

mark printing area with dark ink.

…………

2.3 Power supply specifications

1) Power voltage : DC24V±5%

2) Current consumption *2, *3

NP-215/225 NP-325 NP415W

1 partition 2 partition 1 partition 2 partition 1 partition 2 partition

Standby Approx. 0.1A

ASCII printing

(Printing average of 16%)

Approx.

1.4A

Approx.

0.9A

Approx.

1.7A

Approx.

1.1A - Approx.

1.3A

Bit image printing

(Max 100%)

Approx.

6.0A

Approx.

3.2A

Approx.

7.8A

Approx.

4.1A - Approx.

5.7A

*2: A sufficient volume of power supply is required to maintain print quality due to high peak current

that may run according to printing.

*3: If power supply cable is excessively long, the operation may become unstable. Cable should be

made as short as possible. If not available, connect cables near the printer and place an electrolysis

condenser of 2200μbetween power supply and ground. Voltage resistance should be higher than

35V.

* For preventing from static electric discharge, make sure to connect FG wire.

2.4 Reliability

1) Head life : Average resistance change rate to head less than 15%, except

defects caused by dust or others

Pulse : More than 100 million pulses (with recommended paper)

Wear distance : More than 50 km (with recommended paper)

2) Operation environment : Temperature 0 – 45℃

Print guarantee 5 - 40℃, no condensation

3) Storage environment : Temperature -20 - 60℃

* When storing for a long time, paper must be kept loaded between head and platen.

4) Frame Ground (FG) wire

The FG wire (Green and Yellow) is coming from the printer body. Make sure to ground the wire

near the body frame when installing the printer. FG grounding is effective for minimizing the noise

level, preventing from SED and maintaining the FG safety for head, cutter, body frame, power

supply and Data connectors.

5) Safety regulation

CE marking

UL60950

6) EMC

EMI: EN55022

VCCI: Class A

FCC: Class A

EMS: EN55024

2.5 Dimensions

1) NP-215 dimensional drawing

frame ground

frame ground wires L=(75)

frame ground

ＮＰ−２１５Ｄ

ＮＰ−２１５Ｒ

paper exit

181.4

59 73

10 10 765

49.4 10.9

60 (33)(33) paper width

φ3.4

φ5.4×3.4

118 27.8

111.3

17.7 148.4

D type

R type

(8)

(φ80)

(54)

)(12027

M3 screw holes to fix frame ground.

60.5

38.7

This drawing is for NP-215P.

2) NP-225 dimensional drawing

frame ground

frame ground wires L=(75)

frame ground

ＮＰ−２２５Ｒ

ＮＰ−２２５Ｄ

)(12027

M3 screw holes to fix frame ground.

10765 10 749.4

192.9

79.3

(54)

17.7

118

60 (33)(33)

φ5.4×3.4

paper exit

paper width

120.8

60.5

124

38.7

φ3.4

This drawing is for NP-225P.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Star Micronics Imprimante

Star Micronics

Star Micronics NX-2460 Manuel utilisateur

Star Micronics

Star Micronics Star DP8340 Manuel utilisateur

Star Micronics

Star Micronics lC-10 Manuel utilisateur

Star Micronics

Star Micronics Radix Manuel utilisateur

Star Micronics

Star Micronics FVP10 SERIES Manuel utilisateur

Star Micronics

Star Micronics Multi-Font NX-2410 Manuel utilisateur

Star Micronics

Star Micronics NR-10 Manuel utilisateur

Star Micronics

Star Micronics TSP1000 Series Guide de référence rapide

Star Micronics

Star Micronics DP-8340 FM-120 Manuel utilisateur

Star Micronics

Star Micronics TSP600 Series Manuel utilisateur

Star Micronics

Star Micronics SP2000 Manuel utilisateur

Star Micronics

Star Micronics LC-6211 Manuel utilisateur

Star Micronics

Star Micronics TUP500 series Manuel utilisateur

Star Micronics

Star Micronics LaserPrinter4 Manuel utilisateur

Star Micronics

Star Micronics SP300 Series Manuel d'utilisation et d'entretien

Star Micronics

Star Micronics TSP043E Series Manuel utilisateur

Star Micronics

Star Micronics ND-10/15 Manuel utilisateur

Star Micronics

Star Micronics TUP900 Series Manuel utilisateur

Star Micronics

Star Micronics SP717 Series Manuel utilisateur

Star Micronics

Star Micronics SP2000 Manuel d'utilisation et d'entretien

Star Micronics

Star Micronics gemini-10X Manuel utilisateur

Star Micronics

Star Micronics SP500 Series Manuel utilisateur

Star Micronics

Star Micronics TSP043 Series Manuel utilisateur

Star Micronics

Star Micronics TUP900 Series Manuel utilisateur

Manuels Imprimante populaires d'autres marques

Lexmark

Lexmark 1400 Series Manuel

Canon

Canon i70 Series Manuel utilisateur

Evolis

Evolis Elypso Manuel utilisateur

Kyocera

Kyocera FS-9530DN Manuel utilisateur

Canon

Canon LASER SHOT LBP-1210 Manuel utilisateur

Samsung

Samsung BIXOLON SRP-350plusF Manuel utilisateur

Canon

Canon PIXMA PRO-1 Series Manuel utilisateur

Canon

Canon PIXMA G3560 Guide de configuration

Dell

Dell Color Laser Printer 2130cn Manuel utilisateur

Tektronix

Tektronix Phaser 840 Manuel utilisateur

Epson

Epson ET-7750 Mode d'emploi

Canon

Canon CLBR 460ps Manuel utilisateur

Eltron

Eltron P210 Guide Manuel utilisateur

Ricoh

Ricoh MD-P1 Manuel utilisateur

Epson

Epson SC-F7100 series Manuel utilisateur

Epson

Epson Stylus C40UX Manuel utilisateur

Canon

Canon imagePASS-A2 Manuel utilisateur

Canon

Canon S820D Manuel utilisateur