Star Micronics DP8340RC Series Manuel utilisateur
DOT MATRIX PRINTER
DP8340RC SERIES
[PARALLEL INTERFACE]
USERS MANUAL
Federal Communications Commission
Radio Frequency Interference
Statement
ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassAdigitaldevice,
pursuanttoPart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotection
against harmful interference when the equipment is operated in a commercial environment.
Thisequipment generates,uses andcan radiateradio frequencyenergy and,if notinstalled and
used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interferenceinwhichcasetheuserwillberequiredtocorecttheinterferenceathisownexpense.
For compliance with the Federal Noise Interference Standard, this equipment requires a
shielded cable.
This statement will be applied only for the printers marketed in U.S.A.
Statement of
The Canadian Department of Communications
Radio Interference Regulations
Thisdigitalapparatus doesnotexceed theClassA limitsforradio noiseemissionsfrom digital
apparatus set out in the Radio Interference Regulations of the Canadian Department of
Communications.
Le présent appareil numérique n’émet pas de bruits radioélectiques dépassant les limites
applicables aux appareils numériques de la classe A prescrites dans le Règlement sur le
brouillage radioélectrique édicté par le ministère des Communications du Canada.
The above statement applies only to printers marketed in Canada.
Trademark acknowledgments
DP8340RC: Star Micronics Co. Ltd.
Notice
• All rights reserved. Reproduction of any part of this manual in any form whatsoever, without STAR’s express
permission, is strictly forbidden.
• The contents of this manual are subject to change without notice.
• All efforts have been made to ensure the accuracy of the contents of this manual at the time of printing. However,
should any errors be found, STAR would greatly appreciate being informed of them.
• The above notwithstanding, STAR can assume no responsibility for any errors in this manual.
© Copyright 1986, 1999 Star Micronics Co., Ltd.
TABLE OF CONTENTS
1. OUTLINE..............................................................................................1
2. UNPACKING AND INSTALLATION................................................2
2-1. Unpacking ....................................................................................2
2-2. Installation of Paper Holders and Re-Roll
Prevention Guard .........................................................................3
2-3. Handling Notes.............................................................................4
3. PART IDENTIFICATION AND NOMENCLATURE ........................5
3-1. Power Supply Unit .......................................................................5
3-2. Printer...........................................................................................6
3-3. Part Functional Description..........................................................7
4. INSTALLATION OF INK RIBBON AND PAPER.............................8
4-1. Installation of Ink Ribbon ............................................................8
4-2. Removal of Ink Ribbon................................................................9
4-3. Paper Insertion ...........................................................................10
4-3-1. For Roll Paper .................................................................10
4-3-2. Roll Paper Installation
(When using the optional Printer Cover 8340R).............11
4-3-3. Validation Option Installation .........................................12
4-4. Roll Paper Removal ...................................................................12
5. CONTROL CODES ............................................................................13
6. GENERAL SPECIFICATIONS..........................................................20
7. INTERFACE .......................................................................................24
7-1. Interface Specifications ..............................................................24
7-2. Interface Timing.........................................................................24
7-3. Connectors and Signals ..............................................................25
7-4. Setting of DIP Switches .............................................................26
7-5. Peripheral Unit Drive Circuit .....................................................27
7-6. Error Condition Alarm Mode.....................................................27
8. WHEN POWER IS SUPPLIED BY THE USER ...............................28
9. CHARACTER CODE LIST................................................................30
– 1 –
1. OUTLINE
The DP8340RC series of serial dot matrix printers is for use in ECR, POS,
electronic instruments, banking machines and computer peripheral equipment.
The DP8340RC series include the following features;
1) 2 color printing (Red and Black)
2) High-speed bidirectional printing (2 line/sec, 29 or 44 columns per line)
3) 9-pin print head
4) Parallel interface (Centronics compatible)
5) Commands for expanded characters, inverted characters, emphasized
characters, red and black printing, and 10CPI or 15CPI characters etc. are
provided, which makes the printer very versatile.
6) Simultaneous Data Communication and Printing
7) 2 Peripheral Drivers
8) One line validation printing (Option)
Model Name Notation
– 2 –
2. UNPACKING AND INSTALLATION
2-1. Unpacking
After opening the box, check if all necessary accessories are included.
(A) Printer
(B) Power Supply Unit
Figure 2-1. Unpacking
1Printer
2User’s Manual
3Paper Holders
4Re-Roll Prevention Guard
5Ink Ribbon
6DIP Switch Cover
1
1Power Supply Unit
2User’s Manual
– 3 –
2-2. Installation of Paper Holders and Re-Roll Prevention Guard
Install the Paper Holders in the intermost holes in the rear of the printer.
Figure 2-2. Installation of Paper Holders
– 4 –
InstalltheRe-RollPreventionWireintheholesoftheprintercover.Twistingthe
Wire as shown in the figure below, will make the installation easier.
Figure 2-3. Installation of Re-Roll Prevention
2-3. Handling Notes
(1) Install the printer near an easily accessible socket-outlet.
(2) Place the unit on a flat and stable surface for operation.
(3) Do not connect the AC Power Plug to the same outlet used for other noise
generating devices (large motors, etc.).
(4) Be careful not to drop paper clips, pins and other foreign objects into the
unit.
(5) Wipe off dirt with a soft cloth soaked in alcohol or benzine. Do not use
Lacquer thinner, Trichlorethelene or Ketone solvents because they may
damage plastic parts.
(6) Use a soft brush, etc. for cleaning the printer mechanism and PCB.
(7) Keep hands out of printer while power is on.
(8) Do not attempt to print when there is no ink ribbon or paper in the unit. The
print head life could be severly reduced.
(9) Ifthepaperisfastened tightly to the roll, the paper may not detach from the
roll when the end is reached.
If this happens, the no paper detection function and paper feed will not
operate.
(10) Always keep the printer cover attached when printing to prevent paper
jams, noise, and other problems.
(11) Always turn the power off before opening the printer cover. (e.g. When
renewing a ink ribbon)
– 5 –
3. PART IDENTIFICATION AND NOMENCLATURE
3-1. Power Supply Unit
Figure 3-1. Power Supply Unit
DC Power Connector (Output)
Shape of AC Power plug will
vary according to destinations.
– 6 –
3-2. Printer
Figure 3-2. Printer: Front View
Figure 3-3. Printer: Rear View
Autres manuels pour DP8340RC Series
1
Ce manuel convient aux modèles suivants
5
Table des matières
Autres manuels Star Micronics Imprimante
Star Micronics
Star Micronics TSP100LAN Manuel utilisateur
Star Micronics
Star Micronics TSP2000 Series Manuel d'utilisation et d'entretien
Star Micronics
Star Micronics TCP300II Series Instructions d'installation
Star Micronics
Star Micronics TUP900 Series Guide de configuration rapide
Star Micronics
Star Micronics TSP552 Manuel utilisateur
Star Micronics
Star Micronics LC-7211 Manuel utilisateur
Star Micronics
Star Micronics LC-90 NX-1010 Manuel utilisateur
Star Micronics
Star Micronics TSP400 Series Manuel utilisateur
Star Micronics
Star Micronics TSP400 Series Manuel utilisateur
Star Micronics
Star Micronics TSP600 Series Manuel
Star Micronics
Star Micronics TSP212 Manuel utilisateur
Star Micronics
Star Micronics FR-10 Manuel utilisateur
Star Micronics
Star Micronics TSP1000 Series Manuel utilisateur
Star Micronics
Star Micronics LC-100+ Manuel utilisateur
Star Micronics
Star Micronics LC-7211 Manuel utilisateur
Star Micronics
Star Micronics TSP200 Series Manuel utilisateur
Star Micronics
Star Micronics LC24-15 Manuel utilisateur
Star Micronics
Star Micronics TSP700II Series Manuel utilisateur
Star Micronics
Star Micronics SG-10 Manuel utilisateur
Star Micronics
Star Micronics TSP100ECO Manuel utilisateur
