Star Micronics TSP2000 Series Manuel d'utilisation et d'entretien

THERMAL PRINTER

TSP552

TSP552II

TSP2000

PROGRAMMER'S MANUAL

Trademark acknowledgments

TSP552, TSP552II, TSP2000: Star Micronics Co., Ltd.

ESC/POS: Seiko Epson Corporation

Notice

•Allrightsreserved.Reproductionofanypartofthismanualinanyformwhatsoever,

without STAR’s express permission is forbidden.

•The contents of this manual are subject to change without notice.

•All efforts have been made to ensure the accuracy of the contents of this manual

atthetimeofgoingtopress.However,shouldanyerrorsbedetected,STARwould

greatly appreciate being informed of them.

•The above notwithstanding, STAR can assume no responsibility for any errors in

this manual.

TABLE OF CONTENTS

1. Dip Switch Setting (TSP552 / 552II) ..................................................................... 1

1-1. Serial Interface Type..................................................................................... 1

1-2. Parallel Interface Type .................................................................................. 2

2. Dip Switch Setting (TSP2000) ............................................................................... 3

2-1. Serial Interface Type..................................................................................... 3

2-2. Parallel Interface Type .................................................................................. 4

3. Control Codes ......................................................................................................... 5

3-1. Star Mode Command Summary ................................................................... 5

3-2. Star Mode Command Specifications ............................................................ 9

3-3. ESC/POS Mode Command Summary ........................................................ 60

4. Character Code Tables ........................................................................................ 62

Please access the following URL

http://www.star-micronics.co.jp/service/sp_sup_e.htm

for the lastest revision of the manual.

– 1 –

1. Dip Switch Setting (TSP552 / 552II)

1-1. Serial Interface Type

DIP-SW 1

Switch

Function ON OFF

1 Data receive error Error is ignored. “?” is printed.

2 Receive buffer size 45 bytes 4 k bytes

3 Handshaking XON/XOFF DTR/DSR

4 Data bit 7 bits 8 bits

5 Parity check Yes No

6 Parity Even Odd

7Baud rate See Table 1.

8DIP-SW 2

Switch

Function ON OFF

1 Handshaking conditions Receive buffer full Offline or

(conditions for BUSY) receive buffer full

2 <FF> Code (Star mode) Form Feed Cut Command

Graphic Adjustment (ESC/POS mode) 203 DPI 180 DPI

3Print density See Table 2.

5 Command STAR ESC/POS

6 Should not be changed (should be set to on).

7 #6 pin reset signal Valid Invalid

8 #25 pin reset signal Valid Invalid

Table 1 Baud Rate

Data Rate SW 1-7 SW 1-8

2400 ON ON

4800 OFF ON

9600 ON OFF

19200 OFF OFF

Table 2 Print Density

Print Density SW 2-3 SW 2-4 Contents of Test Print Page

Light ON ON Level 1

(Standard) OFF ON Level 2

ON OFF Level 3

Dark OFF OFF Level 4

– 2 –

1-2. Parallel Interface Type

DIP-SW 1

Switch

Function ON OFF

1 Auto CR Valid Invalid

2 Receive buffer size 45 bytes 4 k bytes

5 Do not change. (Should be set to OFF)

8 Cut position adjust*1 Invalid Valid

(ESC/POS mode only)

*1: Approximately 9mm of paper is fed before cutting.

DIP-SW 2

Switch

Function ON OFF

1 Handshaking conditions Receive buffer full Offline or

(conditions for BUSY) receive buffer full

2 <FF> Code (Star mode only) Form Feed Cut Command

Graphic Adjustment (ESC/POS mode) 203 DPI Adjust for 180 DPI

3Print density See Table 3.

5 Command STAR ESC/POS

6 Do not change. (Should be set to ON)

7 ACK plus width 1 µs8µs

8 #31 pin (INIT) reset signal Valid Invalid

Table 3 Print Density

Print Density SW 2-3 SW 2-4 Contents of Test Print Page

Light ON ON Level 1

(Standard) OFF ON Level 2

ON OFF Level 3

Dark OFF OFF Level 4

– 3 –

2. Dip Switch Setting (TSP2000)

2-1. Serial Interface Type

DIP-SW 1

Switch

Function ON OFF

1 Data receive error Error is ignored. “?” is printed.

2 Receive buffer size 68 bytes 4 k bytes

3 Handshaking XON/XOFF DTR/DSR

4 Data bit 7 bits 8 bits

5 Parity check Yes No

6 Parity Even Odd

7 Baud rate 19200 bps 9600 bps

8 Automatic Status Back function Valid Invalid

DIP-SW 2

Switch

Function ON OFF

1 Handshaking conditions Receive buffer full Offline or

(conditions for BUSY) receive buffer full

2 <FF> Code (Star mode) Cut Command Form Feed

Graphic Adjustment (ESC/POS mode) 180 DPI 203 DPI

3Print density See Table 2.

5 Should not be changed (should be set to off).

6 Command ESC/POS STAR

7 Pin #25 (INIT) reset signal Valid Invalid

8 Pin #6 (DSR) reset signal INIT DSR

Table 2 Print Density

Print Density SW 2-3 SW 2-4

Power economy mode ON ON

Standard OFF OFF

ON OFF

Dark OFF ON

– 4 –

2-2. Parallel Interface Type

DIP-SW 1

Switch

Function ON OFF

1 Auto CR Valid Invalid

2 Receive buffer size 68 bytes 4 k bytes

3 Should not be changed (should be set to off).

4 Device ID reply Valid Invalid

5 Automatic Status Back function Valid Invalid

6 Negotiation Status Back function Valid Invalid

7Treatment of missing data during reverse Store Delete

8 Cut position adjust *1 Valid Invalid

DIP-SW 2

Switch

Function ON OFF

1 Handshaking conditions Receive buffer full Offline or

(conditions for BUSY) receive buffer full

2 <FF> Code (Star mode) Cut Command Form Feed

Graphic Adjustment (ESC/POS mode) 180 DPI 203 DPI

3Print density See Table 2.

5 Should not be changed (should be set to off).

6 Command ESC/POS STAR

7 Always ON Should be set to on.

*1 ESC/POS mode only

Table 2 Print Density

Print Density SW 2-3 SW 2-4

Power economy mode ON ON

Standard OFF OFF

ON OFF

Dark OFF ON

– 5 –

3. Control Codes

3-1. Star Mode Command Summary

The details of each command are shown in the following sections.

Commands to Select Characters

Control codes Hexadecimal Function Page

codes

<ESC> "R"

1B 52

Select international character set 9

<ESC> <GS> t

1B 1D 74

Select character table 10

<ESC> "/" "1" 1B 2F 31 Select slash zero 10

<ESC> "/" <1> 1B 2F 01

<ESC> "/" "0" 1B 2F 30 Select normal zero 11

<ESC> "/" <0> 1B 2F 00

<ESC> "b"

1B 62

n1 n2 n3 n4

Select bar code printing 11

...

<RS>

...

dk 1E

<ESC> "M" 1B 4D Select 12-dot pitch printing 16

<ESC> "p" 1B 70 Select 14-dot pitch printing 16

<ESC> "P" 1B 50 Select 15-dot pitch printing 16

<ESC> ":" 1B 3A Select 16-dot pitch printing 16

1B 20

Set character spacing 17

<SO> 0E Sets the printing magnified double 17

in character width.

<DC4> 14 Resets the printing magnified in 17

character width.

<ESC> "W"

1B 57

Sets the magnification rate in

character width.

<ESC> <SO> 1B 0E Sets the printing magnified 18

double in character height.

<ESC> <DC4> 1B 14 Resets the printing magnified 18

in character height.

<ESC> "h"

1B 68

Sets the magnification rate 19

in character height

<ESC> "–" "1" 1B 2D 31 Select underlining 19

<ESC> "–" <1> 1B 2D 01

– 6 –

Control codes Hexadecimal Function Page

codes

<ESC> "_" "1" 1B 5F 31 Select overlining 20

<ESC> "_" <1> 1B 5F 01

<ESC> "4" 1B 34 Select highlight printing 21

<ESC> "5" 1B 35 Cancel highlight printing 21

<SI> 0F Inverted printing 21

<DC2> 12 Cancel inverted printing 22

<ESC> "E" 1B 45 Select emphasized printing 22

<ESC> "F" 1B 46 Cancel emphasized printing 22

Commands to Set the Page Format

Control codes Hexadecimal Function Page

codes

<ESC> "C"

1B 43

Set page length in lines 23

1B 43 00

Set page length in inches 23

<ESC> "N"

1B 4E

Set bottom margin 24

<ESC> "O" 1B 4F Cancel bottom margin 24

<ESC> "l"

1B 6C

Set left margin 25

<ESC> "Q"

1B 51

Set right margin 26

Commands to Move the Print Position

Control codes Hexadecimal Function Page

codes

<LF> 0A Line Feed 27

<ESC> "a"

1B 61

Feed paper n lines 27

<FF> 0C Form Feed 27

<HT> 09 Horizontal tab 28

<VT> 0B Vertical tab 28

<ESC> "z" "1" 1B 7A 31 Set line spacing to 4 mm 29

<ESC> "0" 1B 30 Set line spacing to 3 mm 29

– 7 –

Control codes Hexadecimal Function Page

codes

<ESC> "J"

1B 4A

One time n/4 mm feed 29

<ESC> "I"

1B 49

One time n/8 mm feed 29

<ESC> "B"

... <0> 1B 42

n1 n2

... 00 Set vertical tab stops 30

<ESC> "D"

... <0> 1B 44

n1 n2

... 00 Set horizontal tab stops 30

<ESC> <GS> "A"

1B 1D 41

Absolute position setting 31

<ESC> <GS> "R"

n1 n2

1B 1D 52

n1 n2

Relative position setting 31

<ESC> <GS> "a"

1B 1D 61

Alignment 32

Commands to Print Dot Graphics

Control codes Hexadecimal Function Page

codes

<ESC> "K"

<0> 1B 48

m1 m2

Print normal density graphics 34

m1 m2

...

<ESC> "L"

n1 n2

1B 4C

n1 n2 m1 m2

Pring high density graphics 36

m1 m2

<ESC> "k"

<0>

1B 6B

Print fine density graphics 38

<ESC> "X"

n1 n2

1B 58

n1 n2

Print fine density graphics 41

<ESC> <FS> "p"

n m

1B 1C

70 n m

Print NV bit image 42

<ESC> <FS> "q" 1B 1C

Define NV bit image 43

Commands to Print Download Characters

Control codes Hexadecimal Function Page

codes

<ESC> "&" "1" "1" 1B 26 31 31

m1 m2

...

m48 m1 m2

...

m48

Define download character 46

<ESC> "&" <1> <1> 1B 26 01 01

m1 m2

...

m48 n m1 m2

...

m48

<ESC> "&" "1" "0"

1B 26 31 30

Delete a download character 48

1B 26 01 00

<ESC> "%" "1" 1B 25 31 Enable download character set 48

<ESC> "%" <1> 1B 25 01

<ESC> "%" "0" 1B 25 30 Disable download character set 48

<ESC> "%" <0> 1B 25 00

<ESC> <GS> "*" xy 1B 1D 2A 78 79 Definition of download bit image 48

<ESC> <GS> "/"

1B 1D 2F 6D Printing of download bit image 50

Autres manuels pour TSP2000 Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Star Micronics Imprimante

Star Micronics

Star Micronics Star SCP700 Series Manuel d'utilisation et d'entretien

Star Micronics

Star Micronics TSP400 Series Manuel utilisateur

Star Micronics

Star Micronics LC24-30 Colour Manuel utilisateur

Star Micronics

Star Micronics LC-100+ Manuel utilisateur

Star Micronics

Star Micronics NP-IO Manuel utilisateur

Star Micronics

Star Micronics NX-1000 Manuel utilisateur

Star Micronics

Star Micronics LC-1021 Manuel utilisateur

Star Micronics

Star Micronics DP8340R Series Manuel utilisateur

Star Micronics

Star Micronics LC24-15 Manuel utilisateur

Star Micronics

Star Micronics SM-S230I Series Manuel utilisateur

Star Micronics

Star Micronics futurePRNT TSP100 Manuel

Star Micronics

Star Micronics TSP100ECO Manuel utilisateur

Star Micronics

Star Micronics SP312F Manuel utilisateur

Star Micronics

Star Micronics TSP600 Series Manuel utilisateur

Star Micronics

Star Micronics TSP400 Series Manuel d'utilisation et d'entretien

Star Micronics

Star Micronics LaserPrinter 8 Manuel utilisateur

Star Micronics

Star Micronics SP312F Manuel utilisateur

Star Micronics

Star Micronics SP312F Manuel utilisateur

Star Micronics

Star Micronics USB Manuel utilisateur

Star Micronics

Star Micronics Delta Manuel utilisateur

Star Micronics

Star Micronics ND-10/15 Manuel utilisateur

Star Micronics

Star Micronics TSP700 Series Manuel utilisateur

Star Micronics

Star Micronics NX-1500 Manuel utilisateur

Star Micronics

Star Micronics TSP400 Series Manuel utilisateur

Manuels Imprimante populaires d'autres marques

Lexmark

Lexmark 1400 Series Manuel

Canon

Canon i70 Series Manuel utilisateur

Evolis

Evolis Elypso Manuel utilisateur

Kyocera

Kyocera FS-9530DN Manuel utilisateur

Canon

Canon LASER SHOT LBP-1210 Manuel utilisateur

Samsung

Samsung BIXOLON SRP-350plusF Manuel utilisateur

Canon

Canon PIXMA PRO-1 Series Manuel utilisateur

Canon

Canon PIXMA G3560 Guide de configuration

Dell

Dell Color Laser Printer 2130cn Manuel utilisateur

Tektronix

Tektronix Phaser 840 Manuel utilisateur

Epson

Epson ET-7750 Mode d'emploi

Canon

Canon CLBR 460ps Manuel utilisateur

Eltron

Eltron P210 Guide Manuel utilisateur

Ricoh

Ricoh MD-P1 Manuel utilisateur

Epson

Epson SC-F7100 series Manuel utilisateur

Epson

Epson Stylus C40UX Manuel utilisateur

Canon

Canon imagePASS-A2 Manuel utilisateur

Canon

Canon S820D Manuel utilisateur