Stack-On QAS-1514-B Manuel utilisateur

Serial #:

Instructions

QAS-1514-B

NOTE: You can store your Key # and Serial # on Stack-On’s

SECURE web site – www.stack-on.com under Customer

Service.

Storing your Key # will provide instant access to this

important information should you ever lose your keys.

Only you will have access to this information.

CONTROL FEATURES

1. Key lock

2. Biometric Key pad

3. Reset button (inside safe)

4. Battery Compartment (inside safe)

• Record the serial number from the tag on the

door front.

• Keep keys and in a secure place away from

children.

• DO NOT STORE YOUR KEYS INSIDE THE

SAFE.

Tools Required:

Drill

10 mm Wrench

3/16” (5 mm) drill bit for drilling into wood

Hardware Included:

(6) Lag screws ᴓ6mm X 48 MM Legnth

(6) Washers

(6) Plastic anchors

40667-1512 115

IMPORTANT

GETTING STARTED INSTALLING THE BATTERY

When you rst receive your safe you will need to

open the door with the key in order to install. A

baery is included and is located in the top of

the Styrofoam packaging.

To open the safe, insert key into lock and turn

counter clockwise until the holster

compartment automatically opens.

To access the baery compartment you will

need to open the holster compartment

completely.

At the very back of the compartment you will

see two L shaped brackets. Rotate the L

brackets towards the top of the safe, so they are

released from the guides en squeeze the two

brackets together so they almost meet - this will

immediately release the compartment from the

sides of the safe body as shown in gure 1. Let

the holster compartment open all the way.

Rotate the L brackets back so they are at

against the back of the holster compartment as

shown in gure 2.

NOTE: Leave the key in the lock while you

install the baeries.

is safe uses 4 AAA alkaline baeries. Under

normal use the baeries will last about a year.

NOTE: If the baeries are low the indicator light

will ash blue when you start scanning. Replace

with 4 new AAA alkaline baeries as shown.

Locate the baery compartment at the very

back of the top of the safe, slide o the baery

cover.

40667-1512 215

Inside safe

Battery

NOTE: is key has also be provided in case

the baeries run low. If you lose your key,

you may purchase a replacement key by

referencing the serial number located on the

front of the door. See section regarding

replacement keys for further information.

Battery Cover

CLOSING THE SAFE

Li up the up the holster compartment until

the L shaped brackets clear the inside of the

frame. Rotate the L bracket back so they point

to the top of the safe and then push them out

towards the safe body which will hold the

holster compartment up. en rotate the L

brackets back into the guides on the back of the

holster compartment.

Close the compartment and hold it closed

until the green light goes on and the unit

beeps.

NOTE: Reset buon is only

accessible when the locking

mechanism is in the un-locked

position.

NOTE: To verify your ngerprint the

locking mechanism must be in the

locked position.

NOTE: When closing the safe with a pistol in the

holster compartment, make sure the pistol does

not interfere with the frame of the safe.

40667-1512 315

Inside safe

Reset Button

Inside safe

RECORDING FINGERPRINTS

When you rst receive your safe there are no

recorded ngerprints. For security you must

record a ngerprint. Failure to do so will

compromise the safety and security of the safe.

You can record up to 20 dierent ngerprints

for opening the safe.

To record a ngerprint, rst press the Reset Buon on

the inside of the safe. e scanner will turn blue with

two beeps (if the sound is turned on) and the blue

light ashes twice, you will then record the same

nger three times as follows:

1. Press the scanner with the selected nger

until there is one beep (if the sound is turned

on) and the green light ashes once. Li your

nger o the scanner.

2. Press the scanner for a second time with the

same nger (holding the nger in a slightly

dierent position) until there is one beep (if

the sound is turned on) and the green light

ashes once. Li your nger o the scanner.

3. Press the scanner for a third time with the

same nger (holding the nger in a slightly

dierent position) until there are two beeps (if

the sound is turned on) and the green light

ashes twice. Li your nger o the scanner.

If the red light ashes three times with three

beeps (if the sound is turned on) your ngerprint

did not get recorded and you will have to start

over.

Your ngerprint is now recorded.

If you try entering more than 20 ngerprints, the

red light will ash 5 times and there will be 5

beeps (if the sound is turned on).

For convenience, record several dierent ngers

and record the most used nger several times.

Position nger on scanner as shown below.

REMOVING THE SAFE FROM THE

MOUNTING BRACKET

40667-1512 415

Mounting

Bracket

Thumb nuts

OPENING THE SAFE USING YOUR

FINGERPRINT

To open the safe, press the scanner with a recorded

nger. e blue light will come on with one beep

(if the sound is turned on) and the scan will begin.

If the green light ashes twice with 2 beeps (if the

sound is turned on), the scan has been accepted

and the door will open.

If the red light ashes once, the scanner did not

read your ngerprint and you must try again. If the

red light ashes 3 times, the scanner read your

ngerprint and did not accept it.

If there are 3 rejected scans, where your

ngerprint was read, and the red light ashes 5

times with 5 beeps (if the sound is turned on),

you will have an automatic lockout for 60

seconds before you can try a scan again. e safe

will beep one time (if the sound is turned on)

and the green light will ash once when the

lockout period is over.

If there is 1 more rejected scan where your

ngerprint was read and the red light ashes 5 times

with 5 beeps (if the sound is turned on), you will

have an automatic lockout for 5 minutes before you

can try a scan again. e safe will beep one time (if

the sound is turned on) and the green light will ash

once when the lockout period is over.

To close the safe, push the door closed until

locked.

TURNING THE SOUND OFF/ON

CLEARING THE MEMORY

To turn the sound o, press the scanner with a

recorded ngerprint for 10 seconds until the green

light ashes twice.

To turn the sound on, press the scanner with a

recorded ngerprint until you hear two beeps and

the green light ashes twice.

Your safe comes with the beep sound turned on.

To clear the memory of all recorded ngerprints,

locate the reset buon on the inside of the safe

and press this buon for about 5 seconds until

the green light ashes 10 times with 10 beeps (if

the sound is turned on). All recorded scans will

be erased.

NOTE: For security you must record a

ngerprint. Failure to do so will compromise

the safety and security of the safe.

Open the holster compartment as described in the

Installing the Baery section. When the holster

compartment has been released from the frame and

the L brackets have been rotated so they are at

against the back of the holster compartment, locate

2 nuts which are located in the boom of the safe

body. Remove the 2 nuts and washers using your

ngers and li the safe o the tabs in the back of the

sleeve.

ere are some securing tabs on the mounting

sleeve that guide the back of the safe into position -

you will need to make sure you have maneuvered the

safe out of these tabs.

STACK-ON PRODUCTS CO.

P.O. BOX 489, WAUCONDA, IL 60084

e safe must be secured to the mounting bracket.

e safe installed in the mounting bracket must be

mounted to a wall or solid surface.

For optimal

safety and security, the safe should be installed in

an isolated, dry and secure area.

SECURING THE SAFE

SELECTING A LOCATION

NOTE: is safe must always be secured in the

mounting bracket and mounted to a wall or

solid surface. Failure to do so will compromise

the safety and security of the safe.

Secure the mounting bracket to wall studs using

the pre-drilled mounting holes in the bracket and

hardware provided.

NOTE ON LOCKING THE SAFE: e safe

needs to be in an upright position, as shown in

gure 3, for the locking mechanism to

function properly. Failure to mount the safe

in the correct upright position will

compromise the safety and security of the

safe.

NOTE: e mounting bracket must be

secured to a wall stud on one side of the

bracket in the top and boom holes so that it

is anchored to the wall stud in two locations.

Wall anchors should be used on the other side.

e bracket should be secured in 4 locations.

Use the hardware provided or consult your

hardware retailer for fastening hardware for

your particular mounting surfaces. Aer the

mounting bracket is secured you must secure

the safe to the bracket to insure the optimal

safety and security of the safe.

Place the mounting bracket in the desired

location and mark the mounting holes to be

used with a pencil. Move the mounting bracket

and drill the pilot holes for the screws. For

mounting to a wall stud, drill a 3/16” diameter

pilot hole and aach the bracket using the Lag

screws and washers.

Place the safe back into the mounting bracket

and replace the 2 thumb nuts and washers.

Secure the holster compartment in place,

following the steps in Closing e Safe section

of these instructions. Close and lock the safe

THE SAFE SHOULD ALWAYS BE KEPT

OUT OF THE REACH OF CHILDREN.

40667-1512 515

Lag screws

Mounting

Bracket

IMPORTANT

Keep your keys in a secure place, away from

children. Keep this record of your serial number in a

secure place separate from your safe. To order a

replacement key set, follow the instructions on the

aached form.

e biometric scanner may be cleaned with

household glass cleaner and a coon cloth.

MAINTENANCE

Key Request

“This is not a Registration Form”

Verification of ownership is required in order to receive replacement key for your security product.

In order to receive a replacement key to your security product:

1. Complete the following form and send to Stack-On Products.

2. Send a copy of your valid driver’s license along with the form.

3. Send a copy of the receipt showing the original purchase.

4. Security product owner must sign form.

5. Owner’s signature must be notarized.

6. Send $10.00 for replacement key. Personal Check, MasterCard, or Visa accepted.

7. Send completed information to:

Stack-On Products Company

1360 N. Old Rand Road

P.O. box 489

Wauconda, IL 60084

Serial Number______________________ Key Number (if applicable) _______

Unit Dimensions________________________________________

Unit Description___________________________________________________________

Owner’s Name ____________________________________ Date Purchased___/___/____

Owner’s Address ___________________________ Unit or Apt Number _________________

City ___________________________ State _______________ Zip Code________________

Telephone Number: (____)___________________ Fax Number: (____)___________________

Owner’s Email Address: ________________________________________________________

Owner’s Signature __________________________ Notary Signature________________

Notary Commission Expires: _____/_____/_____ Notary Stamp

SERVICE REQUESTED

Key Replacement: Yes No

$10.00 charge for this service

Credit Card Information (Please circle one) MasterCard Visa

Expiration Date: ___/___/___ Card Number:______________________________________

Credit Card Identification Number (Located on back of card, last 3 digits on signature strip)_________

9/07

NOTE: You can store your Key #, Serial # and Combination on Stack-On’s SECURE web site – www.stack-on.com under

Customer Service. Storing your Key # or Combination will provide instant access to this important information should you

ever lose your keys or your combination.

Only you will have access to this information.

40667-1512 615

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS

WHICH VARY FROM STATE TO STATE.

IN NO EVENT SHALL STACK-ON’S OBLIGATION UNDER THIS WARRANTY EXCEED THE PRICE

OF THE PRODUCT.

STACK-ON’S LIABILITY FOR ANY BREACH OF THIS WARRANTY SHALL BE LIMITED

EXCLUSIVELY TO REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT, AS DESCRIBED

ABOVE, OR A REFUND OF THE PURCHASE PRICE OF THE PRODUCT.

STACK-ON WILL NOT, UNDER ANY CIRCUMSTANCES, BE LIABLE TO THE INITIAL CONSUMER

FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL, EXEMPLARY, OR PUNITIVE DAMAGES

ARISING OUT OF THE PURCHASE OR USE OF ANY STACK-ON PRODUCTS, INCLUDING THE

SAFES.

THIS WARRANTY IS EXCLUSIVE AND EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES

EXPRESSED OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE, WHICH ARE HEREBY DISCLAIMED AND EXCLUDED. STACK-ON

SHALL NOT BE SUBJECT TO ANY OTHER OBLIGATIONS OR LIABILITIES. STACK-ON NEITHER

ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT, ANY OTHER LIABILITY

IN CONNECTION WITH THE SALE OF STACK-ON’S STEEL SAFES.

THIS WARRANTY DOES NOT COVER ANY PRODUCT, OR ANY PART OF ANY PRODUCT, WHICH

HAS BEEN SUBJECT TO EXCESSIVE USE, ACCIDENT, NEGLIGENCE, ABUSE OR MISUSE,

INCORRECT MAINTENANCE, ALTERATION OR REPAIR BY ANYONE OTHER THAN STACK-ON. IN

ADDITION, THIS WARRANTY DOES NOT COVER ANY ACCESSORIES OR PARTS USED WITH OR

IN THE PRODUCT WHICH ARE NOT INCLUDED WITH THE ORIGINAL PURCHASE.

If Stack-On is properly notified during the three-year warranty period and, after inspection confirms there

is a defect, Stack-On will, at its sole option, provide repair parts or exchange the product at no charge, or

refund the purchase price of the product.

Stack-On Products Company

1360 North Old Rand Road

Wauconda, IL 60084

[email protected]

If you believe there is a defect in material or workmanship in your Steel Safe during the three-year

warranty period, please contact our customer service department, by regular mail or email at the address

listed below, and include with your correspondence proof of purchase information and the model number

of the safe.

Stack-On Products Co. (“Stack-On”) Steel Safes are warranted to be free from defects in material and

workmanship for a period of three (3) years from the date of original purchase by a consumer. This

warranty extends to the initial consumer only.

LIMITED THREE YEAR WARRANTY

STEEL SAFES

40667-1512 715

Serial #:

Instrucciones

QAS-1514-B

NOTA : Usted puede almacenar su clave # y Serial # en el

sitio web seguro de Stack -On - www.stack-on.com bajo

Servicio al Cliente .

Almacenamiento Clave # ofrecerá acceso instantáneo a la

información importante en caso de que alguna vez pierda

sus llaves .

Sólo tendrá acceso a esta información.

FUNCIONES DE CONTROL

1. Bloqueo del teclado

2. Biométrico teclado numérico

3. Botón Reset (en el interior)

4. Compartimiento de la batería (en el

interior)

• Anote el número de serie de la etiqueta en la parte

frontal de la puerta.

• Mantenga las llaves y en un lugar seguro lejos

de los niños .

• NO GUARDE LAS LLAVES DENTRO LA CAJA

FUERTE.

Herramientas necesarias:

Broca

10 mm Llave

3/16 " ( 5 mm ) broca para perforar madera

Hardware incluido:

( 6 ) Lag tornillos ᴓ 6mm X 48 MM Legnth

(6) Arandelas

(6) anclajes de plástico

IMPORTANTE

40667-1512 815

PARA COMENZAR INSTALACIÓN DE LA BATERÍA

La primera vez que reciba su caja fuerte tendrá

que abrir la puerta con la llave con el n de

instalar. Una batería está incluido y se

encuentra en la parte superior del embalaje de

espuma de poliestireno .

Para abrir la caja fuerte, inserción llave en la

cerradura y girar hacia la izquierda hasta que el

compartimiento de la funda se abre

automáticamente.

Para acceder al compartimento de la batería que

tendrá que abrir el compartimento de la funda por

completo.

En la parte trasera del compartimento verá

soportes en forma de L de dos . Gire los soportes

en L hacia la parte superior de la caja fuerte , por lo

que se liberan de las guías Luego apretar los dos

soportes juntos para que casi cumplen - esto dará a

conocer inmediatamente el compartimiento de los

lados del cuerpo de seguridad como se muestra en

la gura 1. Deje que el compartimiento de la funda

abierto todo el camino. Girar los soportes en L

hacia atrás por lo que son plana contra la parte

posterior del compartimiento de la funda como se

muestra en la gura 2 .

NOTA : Deje la llave en la cerradura mientras

instala las baterías.

Este seguro utiliza 4 baterías alcalinas AAA .

En condiciones de uso normal, las pilas

duran alrededor de un año .

NOTA : Si las baterías están bajas la luz

indicadora parpadee en azul cuando se inicia

el escaneado. Reemplace con 4 nuevas

baterías alcalinas AAA como se muestra .

Localice el compartimento de la batería en la

parte posterior de la parte superior de la caja

fuerte , deslice la tapa de la batería.

Inside safe

Batería

NOTA: Esta tecla también se ha previsto en

caso de que las baterías se agotan . Si usted

pierde su llave, usted puede comprar una llave

de reemplazo haciendo referencia al número

de serie ubicado en la parte frontal de la

puerta. Ver sección sobre llaves de repuesto

para más información.

Tapa de la batería

40667-1512 915

NOTA : Restablecer botón sólo

está accesible cuando el

mecanismo de bloqueo está en la

posición de no- bloqueo.

Inside safe

GRABACIÓN DE HUELLAS

DIGITALES

La primera vez que reciba su caja fuerte no hay

huellas digitales registradas. Para mayor

seguridad se debe registrar una huella digital .

De no hacerlo, pondrá en peligro la seguridad

y la seguridad de la caja fuerte.

Puede grabar hasta 20 huellas digitales

diferentes para la apertura de la caja fuerte.

Para registrar una huella digital, primero pulse el

botón de reinicio en el interior de la caja fuerte. El

escáner se vuelve azul con dos pitidos ( si el sonido

está activado ) y la luz azul parpadea dos veces, a

continuación, grabar el mismo dedo tres veces de la

siguiente manera :

1. Pulse el escáner con el dedo seleccionado

hasta que haya un pitido ( si el sonido está

activado ) y la luz verde parpadea una vez .

Levante el dedo del escáner.

2. Pulse el escáner por segunda vez con el

mismo dedo ( sosteniendo el dedo en una

posición ligeramente diferente) hasta que haya

un pitido ( si el sonido está activado ) y la luz

verde parpadea una vez . Levante el dedo del

escáner.

3. Pulse el escáner por tercera vez con el mismo

dedo ( sosteniendo el dedo en una posición

ligeramente diferente ) hasta que hay dos

pitidos ( si el sonido está activado ) y la luz

verde parpadea dos veces . Levante el dedo del

escáner.

Si la luz roja parpadea tres veces con tres pitidos

(si el sonido está activado) su huella digital no

consiguió registrada y usted tendrá que empezar

de nuevo.

Su huella digital se registra ahora .

Si intenta introducir más de 20 huellas digitales ,

la luz roja parpadea 5 veces y habrá 5 pitidos (si el

sonido está activado) .

Para mayor comodidad , grabar varios dedos

diferentes y registrar el dedo más utilizado en

varias ocasiones. Posición dedo sobre el escáner

como se muestra a continuación.

Reset Button

Dentro

40667-1512 1015

Table des matières

Langues :

Autres manuels Stack-On Sûr

Stack-On

Stack-On PS-15-20-B Manuel utilisateur

Stack-On

Stack-On PS-5-B-12 Manuel utilisateur

Stack-On

Stack-On PS-15-05-B Manuel utilisateur

Stack-On

Stack-On QAS-1200B Manuel utilisateur

Stack-On

Stack-On GCB-18C Manuel utilisateur

Stack-On

Stack-On PWS-1555 Manuel utilisateur

Stack-On

Stack-On TD5518-24-GP-E-S Manuel utilisateur

Stack-On

Stack-On PDS-1500 Manuel utilisateur

Stack-On

Stack-On TD-40-SB-B-S Manuel utilisateur

Stack-On

Stack-On QAS-450 Manuel utilisateur

Stack-On

Stack-On PWS-15522-B Manuel utilisateur

Stack-On

Stack-On E-69-MB-B-S Manuel utilisateur

Stack-On

Stack-On Sentinel GCWB-18 Manuel utilisateur

Stack-On

Stack-On TD14-22-GP-E-S Manuel utilisateur

Stack-On

Stack-On GCB-1522 Manuel utilisateur

Stack-On

Stack-On QAS-1512 Manuel utilisateur

Stack-On

Stack-On Security Plus QAS-710 Manuel utilisateur

Stack-On

Stack-On TD-24-GP-C-S Manuel utilisateur

Stack-On

Stack-On PC-1702-RFID Manuel utilisateur

Stack-On

Stack-On TS-20-MB-E-S Manuel utilisateur

Stack-On

Stack-On SS-16-MB-B Manuel utilisateur

Stack-On

Stack-On W-24-BH-E-S Manuel utilisateur

Stack-On

Stack-On QAS-450-B Manuel utilisateur

Stack-On

Stack-On W-22-BH-E-S Manuel utilisateur

Manuels Sûr populaires d'autres marques

Squire

Squire Stronghold Keysafe Manuel utilisateur

Phoenix

Phoenix FS0352C Fiche d'information produit

Phoenix

Phoenix KS0030E Series Manuel utilisateur

Vaultek

Vaultek 10 Series Fiche technique

Arregui

Arregui CLASS Manuel utilisateur

Beaumont

Beaumont SMART KEYBOX Manuel utilisateur

Honeywell

Honeywell 2077D - 1.21 Cubic Foot Anti-Theft Safe Manuel utilisateur

Hornady

Hornady SnapSafe Trunk Safe II Manuel utilisateur

SPORTS AFIELD

SPORTS AFIELD SA-HD5-BIO Manuel utilisateur

Honeywell

Honeywell 5912 Manuel utilisateur

Phoenix

Phoenix FS1280F Manuel utilisateur

Phoenix

Phoenix SS0992K Fiche d'information produit

Technomax

Technomax Trony Series Manuel

SPORTS AFIELD

SPORTS AFIELD INSTINCT BIOMETRIC Series Manuel utilisateur

RICHTER CZECH

RICHTER CZECH LA Manuel d'utilisation

Olymp

Olymp GOsafe 110 Manuel utilisateur

Phoenix

Phoenix SS0100E Fiche d'information produit

Clarke

Clarke Strong-Arm CS1000K Mode d’emploi