ST STEVAL-IFP045V1 Manuel utilisateur
Introduction
The STEVAL-IFP045V1 is an industrial digital output expansion board. It provides a powerful and flexible environment for the
evaluation of the driving and diagnostic capabilities of the IPS1025HQ single high-side smart power solid state relay, in a digital
output module connected to 2.5 A industrial loads.
The STEVAL-IFP045V1 can interface with the microcontroller on the STM32 Nucleo via 5 kV optocouplers driven by GPIO pins
and Arduino R3 connectors.
The expansion board can be connected to either a NUCLEO-F401RE or a NUCLEO-G431RB development board.
It is also possible to evaluate a system composed of up to four stacked STEVAL-IFP045V1 expansion boards.
As an example, a system with four STEVAL-IFP045V1 expansion boards allows you to evaluate a quad channel digital output
module.
Figure 1. STEVAL-IFP045V1 expansion board
Getting started with STEVAL-IFP045V1 industrial digital output expansion board
UM3057
User manual
UM3057 - Rev 1 - August 2022
For further information contact your local STMicroelectronics sales office. www.st.com
1Getting started
1.1 Overview
The STEVAL-IFP045V1 embeds the IPS1025HQ intelligent power switch (IPS), featuring overcurrent and
overtemperature protection for safe output load control.
The board is designed to meet application requirements in terms of galvanic isolation between user and power
interfaces. This requirement is satisfied by an optical isolation implemented through three optocouplers (ISO1,
ISO2, and ISO3) for signal forward to the device and FLT pins for feedback diagnostic signals.
The expansion board features:
• Based on the IPS1025HQ single high-side switch, which features:
– Operating range up to 60 V
– Low-power dissipation (RON(MAX) = 25 mΩ)
– Fast decay for inductive loads
– Smart driving of capacitive loads
– Undervoltage lock-out
– Overload and overtemperature protections
– QFN48L 8x6 mm package
• Application board operating range: 8 to 33 V/0 to 2.5 A
• Extended voltage operating range (J3 open) up to 60 V
• Green LED for output on/off status
• Red LEDs for overload and overheating diagnostics
• 5 kV galvanic isolation
• Supply rail reverse polarity protection
• Compatible with STM32 Nucleo development boards
• Equipped with Arduino UNO R3 connectors
• CE certified
• RoHS and China RoHS compliant
• Not FCC approved for resale
1.1.1 Digital section
The digital section is associated with the STM32 interface and digital supply voltage to and from the STEVAL-
IFP045V1 expansion board.
UM3057
Getting started
UM3057 - Rev 1 page 2/19
Figure 2. STEVAL-IFP045V1 expansion board: digital interface section
Dotted green line indicates the whole digital interface section. Pink rectangles identify Arduino UNO R3 connectors
The four Arduino UNO R3 connectors:
•allow expansion board communication with the STM32 Nucleo development board microcontroller accessing
STM32 peripheral and GPIO resources;
• provide digital supply voltage between the STM32 Nucleo development board and the STEVAL-IFP045V1
expansion board, in either direction.
Normally, the STM32 Nucleo development board supplies the expansion board by a 3v3 or 5v0 generated by the
USB. You can select the preferred voltage on the expansion board via SW3 (3v3 closing pins 1-2; 5v0 closing
pins 2-3).
Alternatively, it is possible to supply the STM32 Nucleo development board by the expansion board. In this case,
an external supply voltage (7-12 V) should be connected to CN2 connector (not mounted by default) on the
expansion board and the ground loop should be closed by mounting D2 (enabling the reverse polarity protection)
or by closing J2 (without reverse polarity).
To supply the VIN voltage rail, it is necessary to:
• close jumper JP5 between pins 2 and 3 and open jumper JP1 on the NUCLEO-F401RE;
• open jumper JP5 between pins 1 and 2 and close jumper JP5 between pins 3 and 4 on the NUCLEO-
G431RB.
UM3057
Overview
UM3057 - Rev 1 page 3/19
1.1.2 Power section
The power section involves the power supply voltage (CN1, pins 4 and 5 for VCC, pin 3 for GND), load
connection (a load can be connected between pins CN1.1 and CN1.3 or CN1.2, and CN1.3; both output pins
are connected to the single output channel as shown in Schematic diagrams) and electromagnetic compatibility
(EMC) protection.
Figure 3. STEVAL-IFP045V1 expansion board: power section components
1. Overtemperature red LED
2. Overload red LED
3. IPS1025HQ
4. Output channel - green LED
5. Output and power supply connector
1
2
3
4
5
For EMC:
•The SM15T39CA transient voltage suppressor (TR1), enabled by closing J3, is placed between VCC and
GND tracks to protect the IPS1025HQ against surge discharge on the supply rail path up to ±1 kV/2 Ω
coupling;
• in common mode surge testing, two single-layer capacitors (C1 and C2 - not included) must be soldered at
the predisposed locations;
• the IPS1025HQ output stages do not require additional EMC protections with respect to the IEC61000-4-2,
IEC61000-4-3, IEC61000-4-4, IEC61000-4-5, IEC61000-4-8 standards.
UM3057
Overview
UM3057 - Rev 1 page 4/19
1.2 Hardware requirements
The STEVAL-IFP045V1 expansion board is designed to be used with the NUCLEO-F401RE or NUCLEO-
G431RB STM32 Nucleo development boards.
To function correctly, the STEVAL-IFP045V1 must be plugged onto the matching Arduino UNO R3 connector pins
on the STM32 Nucleo board as shown below.
Figure 4. STEVAL-IFP045V1 and STM32 Nucleo stack
1.3 System requirements
To use the STM32 Nucleo development boards with the STEVAL-IFP045V1 expansion board, you need:
• a Windows PC/laptop (Windows 7 or above)
• a type A to mini-B USB cable to connect the STM32 Nucleo board to the PC when using a NUCLEO-
F401RE development board
• a type A to micro-B USB cable to connect the STM32 Nucleo board to the PC when using a NUCLEO-
G431RB development board
• the X-CUBE-IPS firmware and software package installed on your PC/laptop
1.4 Board setup
Step 1. Connect the micro-USB or mini/USB cable to your PC to use the STEVAL-IFP045V1 with NUCLEO-
F401RE or NUCLEO-G431RB development board
UM3057
Hardware requirements
UM3057 - Rev 1 page 5/19
Step 2. Download the firmware (.bin) onto the STM32 Nucleo development board microcontroller through
STM32 ST-LINK utility, STM32CubeProgrammer and according to your IDE environment as detailed in
the table below.
Table 1. NUCLEO-F401RE development board supported IDEs - bin files
NUCLEO-F401RE
IAR Keil STM32CubeIDE
EWARM-OUT05_06-
STM32F4xx_Nucleo.bin
MDK-ARM-OUT05_06-
STM32F4xx_Nucleo.bin
STM32CubeIDE-OUT05_06-
STM32F4xx_Nucleo.bin
Table 2. NUCLEO-G431RB development board supported IDEs - bin files
NUCLEO-G431RB
IAR Keil STM32CubeIDE
EWARM-OUT05_06-
STM32G4xx_Nucleo.bin
MDK-ARM-OUT05_06-
STM32G4xx_Nucleo.bin
STM32CubeIDE-OUT05_06-
STM32G4xx_Nucleo.bin
Step 3. Connect the IPS1025HQ device supply voltage via CN1 (see Section 1.1.2 Power section).
Step 4. Provide the digital supply voltage (see Section 1.1.1 Digital section).
Step 5. Connect the load on the output connector (see Section 1.1.2 Power section).
Step 6. Reset the example sequence using the black push button.
Step 7. Push the STM32 Nucleo blue button to select the example provided in the firmware package.
1.5 Multiple board configuration
It is also possible to evaluate a four channel digital output module by stacking four STEVAL-IFP045V1 with shared
or independent supply rail and independent loads.
In this case, the four expansion boards (board 0, 1, 2, 3 as shown in the table below) must be properly configured:
for board 1, 2 and 3, it is necessary to unsolder three resistors for each board from the default position and solder
them back in the alternate positions according to the following table.
Table 3. Configuration of a stack of four expansion boards
Board no. IN1 FLT1 FLT2
Board 0 R101 R103 R114
Board 1 R102 R104 R117
Board 2 R115 R116 R107
Board 3 R120 R119 R118
UM3057
Multiple board configuration
UM3057 - Rev 1 page 6/19
2Schematic diagrams
Figure 5. STEVAL-IFP045V1 circuit schematic (1 of 2)
ALTERNATE USE
ALTERNATE USE
ALTERNATE USE
DEFAULT
PB8
PA6
PB3
PC1
PA8
PB10
VCC
PB4
PC0
Arduino Connectors
PA10
PB9
PB6
PA3
(7V-12V NUCLEO supply voltage)
PA2
PA4
Alternate Nucleo Supply
7V - 12 V
PC7
PA0
OUT
Analog supply
8V - 60 V
PA1
ALTERNATE USE
I OREF
VCC
PA7
ALTERNATE USE
NRST
PA9
DEFAULT
GND
PA5
PB5
OUT
DEFAULT
PB0
Morpho Connectors
(N.M.)
ALTERNATE USE
ALTERNATE USE
ALTERNATE USE
OUT1
ALTERNATE USE
VCC
IN1
FLT1
FLT2
3v3 5v0
CN1
1
2
3
691137710005
4
5
CN5
1
2
3
4
SSQ-110-04-F-S
5
6
7
8
9
10
R116 100 N.M.
R104 100 N.M.
CN7 N.M.
1
SSQ-119-04-L-D
2
3 4
5 6
7 8
9 10
11 12
13 14
15 16
17 18
19 20
21 22
23 24
25 26
27 28
29 30
31 32
33 34
35 36
37 38
R101 100
R115 100 N.M.
FIDUCIAL3
Fiducial
12
+
C10
100uF
N.M.
C1
4700pF
N.M.
MH3
C6
2.2uF
M3 HOLE NOT PLATED
MH2
CN8 M3 HOLE NOT PLATED
1
2
3
4
SSQ-106-04-F-S
5
6
CN9
1
2
3
4
SSQ-108-04-F-S
5
6
7
8
CN10 N.M.
1
SSQ-119-04-L-D
2
3 4
5 6
7 8
9 10
11 12
13 14
15 16
17 18
19 20
21 22
23 24
25 26
27 28
29 30
31 32
33 34
35 36
37 38
TP2
5001
R117 100 N.M.
R120 100 N.M.
R119 100 N.M.
FIDUCIAL1
Fiducial
C2
4700pF
N.M.
MH4
J2 default open
J4
M3 HOLE NOT PLATED
default open
R103 100
D1 STPS1H100A
TR1
12
SM15T39CA
J3
default closed
R114 100
CN6
1
2
3
SSQ-108-04-F-S
4
5
6
7
8
R118 100 N.M.
FIDUCIAL2
Fiducial
TP4
5001
MH1
D2
M3 HOLE NOT PLATED
N.M.
BAT48JFILM
R107 100 N.M.
TR2 N.M.
ESDA15P60-1U1M
CN2
1
N.M.
2
691214110002
FIDUCIAL4
Fiducial
R102 100 N.M.
EARTH
FLT1 D15
FLT1 D14
AVDD
VIN
3V3 D13
5V FLT1 D12
IN1 D11
IN1 D10
VIN IN1 D9
IN1 D8
IN1
FLT1
D7 FLT2
FLT1 D6
A0 D5
A1 FLT2 D4
A2 FLT2 D3
A3 FLT2 D2
A4 FLT2 D1
A5 D0
UM3057 - Rev 1 page 7/19
UM3057
Schematic diagrams
Figure 6. STEVAL-IFP045V1 circuit schematic (2 of 2)
default:
closed
VCC
IN1
FLT1
OUT1
FLT2
3v3
5v0
R11
2.2K
R3
22k
R12
22k
1
ISO1
2
43
J5
J8
default closed
TP3
5001
0
R5
DR1
AC
150060RS75000
1
ISO2
2
43
J1
R4
0
default closed
0
R10
C5
0.1uF
R8
10k
C4
0.1uF
C9470nF
R9
0
R710k
C847nF
C7470pF
U1
IPS1025HQ
FLT2
13
17 OUT_17
18 OUT_18
19 OUT_19
20 OUT_20
21 OUT_21
22 OUT_22
23 OUT_23
24 OUT_24 35
OUT_35
36
OUT_36
37
OUT_37
38
OUT_38
39
OUT_39
40
OUT_40
IPD 48
IN 3
GND 6
FLT1 46
41
OUT_41
42
OUT_42
49 Exp-VCC
SW1
con3-strip-male
1
2
3
default: CLOSE 1-2
SW2
con3-strip-male
1
2
3
default: CLOSE 1-2
DG1
AC
J6
150060VS75000
J7
default closed
DR2
AC
150060RS75000
SW4
con3-strip-male
1
2
3
R2
default: CLOSE 1-2
390
SW3
con3-strip-male
1
2
3
TP5
default: CLOSE 1-2
5001
ISO3
12
43
TP1
5001
J9
1 2
3 4
5 6
con6-2x3-strip-male
R1
27K
R6 2.2K
UM3057 - Rev 1 page 8/19
UM3057
Schematic diagrams
3Bill of materials
Item Q.ty Ref. Part/value Description Manufacturer Order code
1 0 C1 C2
4700pF 1825
(4564 Metric)
3000V (3kV)
10%
CAP CER
4700PF 3KV
X7R 1825 (not
mounted)
Vishay Vitramon HV1825Y472KXHATHV
2 2 C4 C5
0.1uF 0805
(2012 Metric)
100V 10%
CAP CER
0.1UF 100V
X7R 0805
Würth
Elektronik 885012207128
3 1 C6
2.2uF 1206
(3216 Metric)
100V 10%
CAP CER
2.2UF 100V
X7R 1206
AVX
Corporation 12061C225KAT2A
4 1 C7
470pF 0603
(1608 Metric)
50V 5%
CAP CER
470PF 50V
C0G/NP0 0603
Wurth
Electronics Inc. 885012006061
5 1 C8
47nF 0603
(1608 Metric)
50V 10%
CAP CER
0.047UF 50V
X7R 0603
Murata
Electronics
North America
GCM188R71H473KA55D
6 1 C9
470nF 0603
(1608 Metric)
25V 10%
CAP CER
0.47UF 25V
X7R 0603
Wurth
Electronics Inc. 885012206075
7 0 C10 100uF Radial,
Can 100V 20%
CAP 100 UF
20% 100 V (not
mounted)
Würth
Elektronik 860130878011
8 1 CN1 691137710005
TERM BLK
5POS SIDE
ENTRY 5MM
PCB
Würth
Elektronik 691137710005
9 0 CN2 691214110002
7.4X7 pitch 3.5
TERM BLK
2POS SIDE
ENT 3.5MM
PCB (not
mounted)
Wurth
Electronics Inc. 691214110002
10 1 CN5 TH 2.54mm 10 ways, 1 row Samtec Inc.
4UCONN ESQ-110-14-T-S 17896
11 2 CN6 CN9 TH 2.54mm 8 ways, 1 row Samtec Inc.
4UCONN ESQ-108-14-T-S 15782
12 0 CN7 CN10 -
CONN RCPT
38POS 0.1
GOLD PCB (not
mounted)
- -
13 1 CN8 TH 2.54mm 6 ways, 1 row Samtec Inc.
4UCONN ESQ-106-04-T-S 15781
14 1 D1 STPS1H100A,
SMA
100 V, 1 A
power Schottky
rectifier
ST STPS1H100A
15 0 D2 BAT48JFILM,
SOD323
40 V, 350 mA
axial general
purpose signal
Schottky diode
(not mounted)
ST BAT48JFILM
16 1 DG1
150060GS7500
0 0603 (1608
Metric) 20mA
LED GREEN
CLEAR 0603
SMD
Wurth
Electronics Inc. 150060GS75000
UM3057
Bill of materials
UM3057 - Rev 1 page 9/19
Item Q.ty Ref. Part/value Description Manufacturer Order code
17 2 DR1 DR2
150060RS7500
0 0603 (1608
Metric) 20mA
LED RED
CLEAR 0603
SMD
Wurth
Electronics Inc. 150060RS75000
18 3 ISO1 ISO2
ISO3
140109146000
LSOP04
OPTOISO 5KV
TRANSISTOR
Wurth
Electronics Inc. 140109146000
19 7 J1 J2 J3 J4 J5
J6 J8
JUMPER-con2-
strip-male TH
2.54mm
JUMPER-
CONN
HEADER .100
STR 2POS
Wurth
Electronics Inc. 61300211121
20 0 J7 JUMPER-con2-
strip-male
JUMPER-
CONN
HEADER .100
STR 2POS (not
mounted)
- -
21 1 J9 con6-2x3-strip-
male
CONN
HEADER .100
DUAL STR
6POS
Wurth
Electronics Inc. 61300621121
22 1 R1
27K 0603 (1608
Metric) 0.1W,
1/10W 1%
RES SMD 27K
OHM 1% 1/10W
0603
Yageo RC0603FR-0727KL
23 1 R2
390 0603 (1608
Metric) 0.1W,
1/10W 1%
RES SMD 390
OHM 1% 1/10W
0603
Yageo RC0603FR-07390RL
24 2 R3 R12
22k 0603 (1608
Metric) 0.1W,
1/10W 1%
RES SMD 22K
OHM 1% 1/10W
0603
Yageo RC0603FR-0722KL
25 4 R4 R5 R9 R10
0 0603 (1608
Metric) 0.1W,
1/10W Jumper
RES SMD 0
OHM JUMPER
1/10W 0603
Panasonic
Electronic
Components
ERJ-3GEY0R00V
26 2 R6 R11
2.2K 0603
(1608 Metric)
0.1W, 1/10W
1%
RES SMD 2.2K
OHM 1% 1/10W
0603
Yageo RC0603FR-072K2L
26 2 R7 R8
10k 0603 (1608
Metric) 0.1W,
1/10W 1%
RES SMD 10K
OHM 1% 1/10W
0603
Yageo RC0603FR-0710KL
28 3 R101 R103
R114
100 0603 (1608
Metric) 0.1W,
1/10W 1%
RES SMD 100
OHM 1% 1/10W
0603
Yageo RC0603FR-07100RP
29 0
R102 R104
R107 R115
R116 R117
R118 R119
R120
100 0603 (1608
Metric) 0.1W,
1/10W 1%
RES SMD 100
OHM 1% 1/10W
0603 (not
mounted)
Yageo RC0603FR-07100RP
30 4 SW1 SW2 SW3
SW4
con3-strip-male
TH 2.54mm
CONN
HEADER .100
STR 3POS
Wurth
Electronics Inc. 61300311121
31 5 TP1 TP2 TP3
TP4 TP5
5001 0.100" Dia
x 0.180" L
(2.54mm x
4.57mm)
TEST POINT
PC MINI .040"D
BLACK
Keystone
Electronics 5001
32 1 TR1 SM15T39CA,
SMC
1500 W, 33.3 V
TVS in SMC ST SM15T39CA
UM3057
Bill of materials
UM3057 - Rev 1 page 10/19
Table des matières
Autres manuels ST Matériel informatique
ST
ST STDES-65ACFADP Fiche technique
ST
ST ST92163 Manuel utilisateur
ST
ST STLINK-V3PWR Manuel utilisateur
ST
ST X-NUCLEO-IHM12A1 Manuel utilisateur
ST
ST ST7-EMU3 Series Manuel utilisateur
ST
ST X-NUCLEO-OUT09A1 Manuel utilisateur
ST
ST STEVAL-DPSG474 Manuel utilisateur
ST
ST STEVAL-SCR002V1 Manuel utilisateur
ST
ST STM32 Nucleo Manuel utilisateur
ST
ST STM32F405 Series Manuel utilisateur
ST
ST X-NUCLEO-53L3A2 Manuel utilisateur
ST
ST X-NUCLEO-OUT17A1 Manuel utilisateur
ST
ST X-NUCLEO-USBPDM1 Manuel utilisateur
ST
ST X-STM32MP-MSP01 Manuel utilisateur
ST
ST PCC020V1 Manuel utilisateur
ST
ST STM32U5 Nucleo-64 Manuel utilisateur
ST
ST X-NUCLEO-IDB05A2 Manuel utilisateur
ST
ST EVALSPEAr320HMI Manuel utilisateur
ST
ST STM32F3DISCOVERY Manuel utilisateur
ST
ST STEVAL-MIC008A Manuel utilisateur
Manuels Matériel informatique populaires d'autres marques
EMC2
EMC2 VNX Series Manuel du propriétaire
Panasonic
Panasonic DV0PM20105 Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuel utilisateur
Raidon
Raidon iT2300 Manuel utilisateur
National Instruments
National Instruments PXI-8186 Manuel utilisateur
