Spirax Sarco UFT32 Manuel utilisateur
Local regulations may restrict the use of this product to below the conditions quoted.
In the interests of development and improvement of the product, we reserve the right to change the specification without notice. © Copyright 2019
Page 1 of 5
UFT32
Sealed Stainless Steel Ball Float Steam Trap
(for use with Pipeline Connectors)
TI-P146-05
CMGT Issue 6
Description
The UFT32 is an austenitic stainless steel maintenance free sealed ball float steam trap with an integral automatic air venting facility.
It is designed for differential steam pressures up to 32 bar.
When installed with a suitable pipeline connector the UFT32 can easily and simply be removed without breaking into the pipeline, thus
speeding up trap replacement with minimal system downtime. Pipeline connectors are available with screwed, socket weld and flanged
end connections.
Capsule
The BP99/32 capsule which is used in the UFT32 is suitable for use on 150 °C superheat @ 0 bar g and 50 °C superheat @ 32 bar g.
Standards
The body to cover welded joint complies with ASME Section IX and BS/EN 288.
This product fully complies with the requirements of the Pressure Equipment Directive (PED).
Certification
This product is available with certification to EN 10204 3.1.
Note: All certification/inspection requirements must be stated at the time of order placement.
Pipeline connector options
The UFT32 can be fitted to a variety of pipeline connectors including:
PC10HP Straight connector ASME 600 (TI-P128-10)
PC20 Straight connector with 'Y' type strainer ASME 300 (TI-P128-15)
IPC21 Straight connector with 'Y' type strainer and integral Spiratec sensor ASME 300 (TI-P128-15)
PC3 _ Straight connector with one piston isolation valve ASME 600 (TI-P128-02)
PC4 _ Straight connector with two piston isolation valves ASME 600 (TI-P128-03)
S TS17. 2 Steam trap station (TI-P128-22)
See the relevant Technical Information sheet as listed above for details of the connections available for each pipeline connector.
UFT32 fitted to a PC4_ connector
UFT32 fitted to a PC3_ connector
TI-P146-05
CMGT Issue 6
Page 2 of 5
UFT32 Sealed Stainless Steel Ball Float Steam Trap (for use with Pipeline Connectors)
Temperature °C
Pressure bar g
Steam saturation curve
The product must not be used in this region.
The product should not be used in this region or beyond its operating range as damage to the internals may occur.
Note: The model of pipeline connector and connections selected will dictate the maximum operating limits of the complete assembly.
Reference the specific pipeline connector Technical Information sheet as detailed in 'Pipeline connector options'.
Body design conditions PN50 (ASME 300)
PMA Maximum allowable pressure 50 bar g @ 38 °C
TMA Maximum allowable temperature 400 °C @ 28 bar g
Minimum allowable temperature -48 °C
PMO Maximum operating pressure for saturated steam service 32 bar g
TMO Maximum operating temperature 286 °C @ 29 bar g
Minimum operating temperature
Note: For lower operating temperatures consult Spirax Sarco 0 °C
DPMX Maximum differential pressure
UFT32-4.5 4.5 bar
UFT32-10 10 bar
UFT32-14 14 bar
UFT32-21 21 bar
UFT32-32 32 bar
Designed for a maximum cold hydraulic test pressure of: 50 bar g
Pressure/ temperature limits (ISO 6552)
Page 3 of 5
UFT32 Sealed Stainless Steel Ball Float Steam Trap (for use with Pipeline Connectors)
TI-P146-05
CMGT Issue 6
No. Part Material
1Body Austenitic stainless steel 304 EN 10213-4 1.4308;
ASTM A351 CF8
2Cover Austenitic stainless steel 304 EN 10028-7 1.4301;
ASTM A240 Gr. 304
3Connector screws Steel ASTM A193 B7
4Flange Alloy steel - ELNP ASTM A193 B7
5* Inlet gasket Graphite/Stainless steel laminate
6* Outlet gasket Graphite/Stainless steel laminate
7Main valve seat Stainless steel EN10088-3 1.4057
8Main valve/air vent seat gasket Stainless steel EN10088-2 1.4307
9Main valve assembly screws Stainless steel BS EN ISO3506 Cl A2
10 Ball float and lever Stainless steel EN10088-2 1.4301
11 Air vent assembly Stainless steel
12 Pivot frame Stainless steel EN10088-3 1.4057
13 Pivot pin Stainless steel
* Note: Items 5 and 6 are shown clearly in the spares drawing overleaf.
Dimensions/weight (approximate) in mm and kg
ABCWeight
168.5 94 47 2.02
UFT32 fitted to a PC10HP connector
Materials
3
107 2914
11
12
13
B A
C
TI-P146-05
CMGT Issue 6
Page 4 of 5
UFT32 Sealed Stainless Steel Ball Float Steam Trap (for use with Pipeline Connectors)
Safety information, installation and maintenance
For full details see the Installation and Maintenance Instructions (IM-P146-01) supplied with the product.
Installation note:
The UFT32 can be installed on any pipeline connector, but must be installed in a horizontal plane with the ‘TOP’ label facing
upwards See separate Installation and Maintenance Instructions for Spirax Sarco pipeline connectors (IM-P128-06, IM-P128-11
and IM-P128-13).
Disposal
The UFT32 trap unit is manufactured from stainless steel and is therefore totally recyclable. No ecological hazard is anticipated with
the disposal of this product provided due care is taken.
How to specify
Steam traps shall be sealed ball float traps UFT32 type suitable for a differential operating pressure of either 4.5, 10, 14, 21 or 32 bar.
Traps to be zero maintenance and be connected to a separate pipeline connector by two screws to allow for quick and simple installation/
replacement.
For example Spirax Sarco UFT32-32 ball float steam trap.
How to order
The UFT32 is supplied as follows:-
1. The swivel pipeline connector
PC10HP Standard connection
PC20 One integral ISO valve plus 'Y' type strainer
IPC21 One integral ISO valve plus 'Y' type strainer and Spiratec sensor
PC3
_One integral ISO valve
PC4
_Two integral ISO valves
2. The STS17.2 steam trap station
3. The UFT32 trap complete with inner and outer gaskets and two connector screws. These items will be supplied in a protective box.
Note: Any optional extras need to be specified at the time of order placement.
How to order example:
1 off Spirax Sarco DN20 PC10HP pipeline connector with socket weld connections.
or
1 off DN20 STS17 steam trap station having socket weld connections.
and/or if you are ordering a replacement for an existing unit:
1 off Spirax Sarco UFT32-21 sealed stainless steel ball float steam trap.
plus
1 off Spirax Sarco insulating jacket to fit a UFT32.
Please note: The above items are to be supplied with connector screws and gaskets.
Capacities (in accordance with ISO 7842)
Note: Capacities shown are based on discharge at saturation
temperature. When discharging sub-cooled condensate the air
vent provides extra capacity. Under start-up conditions the
thermostatic air vent will be open, and will provide additional
condensate capacity to the main valve assembly. This will provide
a minimum of 100% increased capacity above the hot condensate
figures shown.
For example:
A UFT32-14 has a hot condensate capacity of 195 kg/h at 5 bar
differential. The cold start-up capacity will be a minimum of
390 kg/h.
Differential pressure bar (x 100 = kPa)
Condensate kg/h
Page 5 of 5
UFT32 Sealed Stainless Steel Ball Float Steam Trap (for use with Pipeline Connectors)
TI-P146-05
CMGT Issue 6
365
Spare parts
The UFT32 is a sealed non-maintainable trap unit. No internal spares are available.
The spares that are available are shown in solid outline. Parts shown in a grey line are not available as spares.
Available spares
Connector screws (x 2) 3
Complete UFT32 trap unit inclusive of gaskets and connector screws (3)
How to order spares
Always order spare parts by using the description given in the column headed 'Available spares' and state the size, model no. and
pressure rating of the trap.
Example: 2 x Connector screws for a Spirax Sarco UFT32
sealed stainless steel ball float steam trap (for use with pipeline connectors).
UFT32
trap unit and gaskets
Recommended tightening torques
Item Part or
mm N m
3Connector screws " A/F 33
Autres manuels pour UFT32
1
Table des matières
Autres manuels Spirax Sarco Unité de contrôle
Spirax Sarco
Spirax Sarco RSW Manuel utilisateur
Spirax Sarco
Spirax Sarco HV3 Manuel utilisateur
Spirax Sarco
Spirax Sarco FTC62 Manuel utilisateur
Spirax Sarco
Spirax Sarco M10Si Automation Manuel utilisateur
Spirax Sarco
Spirax Sarco PM6 Manuel utilisateur
Spirax Sarco
Spirax Sarco FTC80 Manuel utilisateur
Spirax Sarco
Spirax Sarco DCV8 Manuel utilisateur
Spirax Sarco
Spirax Sarco DP27 Manuel utilisateur
Spirax Sarco
Spirax Sarco TD3-3 Manuel utilisateur
Spirax Sarco
Spirax Sarco SX100e Fiche technique
Spirax Sarco
Spirax Sarco 211 Manuel utilisateur
Spirax Sarco
Spirax Sarco DN15 Manuel utilisateur
Spirax Sarco
Spirax Sarco Spira-trol K Series Manuel utilisateur
Spirax Sarco
Spirax Sarco PV4 Manuel utilisateur
Spirax Sarco
Spirax Sarco M80i ISO Manuel utilisateur
Spirax Sarco
Spirax Sarco M10S Manuel utilisateur
Spirax Sarco
Spirax Sarco FT 43 Series Manuel utilisateur
Spirax Sarco
Spirax Sarco PF5 Series Manuel utilisateur
Spirax Sarco
Spirax Sarco GKE 10 Mode d’emploi
Spirax Sarco
Spirax Sarco DP27S Manuel utilisateur
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
