SOLTEK SL-55B5 Manuel utilisateur

Notice to End Users

This UserÕs Guide & Technical Reference is for assisting system

manufacturers and end users in setting up and installing the

mainboard.

Every effort has been made to ensure that the information in this

manual is accurate. Soltek Computer Inc. is not responsible for

printing or clerical errors. Information in this document is subject

to change without notice and does not represent a commitment on

the part of Soltek Computer Inc.

No part of this manual may be reproduced, transmitted, translated

into any language in any form or by any means, electronic or

mechanical, including photocopying and recording, for any purpose

without the express written permission of Soltek Computer Inc.

Companies and products mentioned in this manual are for

identification purposes only. Product names appearing in this

manual may or may not be registered trademarks or copyrights of

their respective companies.

SOLTEK COMPUTER INC. PROVIDES THIS MANUAL ÒAS ISÓ

WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED,

INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR

CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE. IN NO EVENT SHALL SOLTEK COMPUTER

INC. BE LIABLE FOR ANY LOSS OR PROFITS, LOSS OF BUSINESS, LOSS

OF USE OR DATA, INTERRUPTION OF BUSINESS, OR FOR INDIRECT,

SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY

KIND, EVEN IF SOLTEK COMPUTER INC. HAS BEEN ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR

ERROR IN THIS MANUAL OR PRODUCT.

Web site: http://www.soltek.com.tw

email: [email protected]

Edition: January 1998

Version: 1.0

SL–55B5 SERIAL

Contents iii

Contents

Chapter 1: Introduction --------------------------------------- 1

Features -------------------------------------------------------------------------1

CPU ------------------------------------------------------------------------1

Chipset -------------------------------------------------------------------- 1

L2 Cache ------------------------------------------------------------------1

Main Memory ----------------------------------------------------------- 1

BIOS ------------------------------------------------------------------------ 3

I/O Function -------------------------------------------------------------3

Other Functions --------------------------------------------------------- 3

Mainboard Setting for Pentium MMX-166----------------------------- 4

Chapter 2: Hardware Setup---------------------------------- 5

CPU VCORE Voltage Setting---------------------------------------------- 5

JP1: CPU VCore Voltage Setting -----------------------------------5

AGP Driver for Win95 Installation --------------------------------------6

Requirement -------------------------------------------------------------6

Installation Procedure -------------------------------------------------6

Intel Pentium MMXÐ166/200/233 CPUs ------------------------------7

AMD K6 CPU Settings------------------------------------------------------8

AMD K6 Ð 166/200/233 CPUs -------------------------------------- 8

AMD K6 Ð 266/300/333/366 CPUs -------------------------------- 9

Cyrix 6x86MX (M2) Ð PR150/166/200/233/266 CPUs----------- 10

Cyrix 6x86(L) Ð PR133+/PR150+/PR166+/PR200+ CPUs------- 11

Intel Pentium/AMD K5 Ð 133/166/200 CPUs---------------------- 12

IDT C6 Ð 200/233/266 ---------------------------------------------------- 12

System Memory Configuration----------------------------------------- 13

Jumper Settings ------------------------------------------------------------- 13

JP2: Clear CMOS Data ---------------------------------------------- 13

SW1: 1~3: CPU Clock Setting ------------------------------------- 14

IDE LED Activity Light: (J1 pin1Ð4)------------------------------ 14

Contents v

Infrared Port Module Connector (J1 pin6Ð10) ----------------- 14

J1 pin12, 13: ATX Power Button ---------------------------------- 14

J1 pin14, 15: Reserved ----------------------------------------------- 14

Speaker Connector (J2 pin1Ð4) ------------------------------------ 15

Reset Switch (J2 pin5, 6)--------------------------------------------- 15

Power LED and Keylock Switch (J2 pin8Ð12)------------------ 15

Turbo LED (J2 pin14, 15)-------------------------------------------- 16

J1 Switch Signal Summary ----------------------------------------- 17

J2 Switch Signal Summary ----------------------------------------- 18

Chapter 3: BIOS Setup ---------------------------------------19

Standard CMOS Setup ---------------------------------------------------- 20

BIOS Features Setup ------------------------------------------------------- 22

Chipset Features Setup --------------------------------------------------- 25

Power Management Setup ----------------------------------------------- 29

PnP/PCI Configuration Setup ------------------------------------------ 31

Load Setup Defaults ------------------------------------------------------- 34

Integrated Peripherals ---------------------------------------------------- 34

Supervisor/User Password---------------------------------------------- 37

IDE HDD Auto Detection ------------------------------------------------ 38

Save & Exit Setup ---------------------------------------------------------- 39

HDD Low Level Format -------------------------------------------------- 39

Exit Without Saving ------------------------------------------------------- 39

Introduction 1

Chapter 1

Introduction

Features

CPU

1. Supports Intel Pentium P54C/MMX (P55C) CPUs at 90

~ 233 MHz;

2. Supports Cyrix 6x86(L) CPUs at PR133+~ PR200+MHz

and 6x86MX (M2) CPUs at PR166+~ PR266+;

3. Supports AMD K5: PR90 ~ PR200 and AMD K6: 166 ~

366;

4. Supports IDT C6: 200 ~ 266;

5. Provides SOCKET 7 ZIF Socket;

6. Supports 75MHz CPU clock;

7. Supports CPU voltage auto detect and switching circuit.

Chipset

1. VIA Apollo VP3 chipset;

2. PCI Rev 2.1 and APM1.1 compliant.

L2 Cache

1. Onboard supports 512k write back cache with Pipelined

Burst SRAMs.

Main Memory

1. Memory range from 4MB (minimum) to 1GB

(maximum) with DRAM Table Free configurations;

2. Supports Fast Page Mode/EDO/Synchronous DRAM

with 60ns/70ns DRAM speed;

3. Supports 2pcs 72pin SIMM sockets and 3 pcs of 168pin

DIMM sockets (3.3V unbuffered type).

BIOS

1. AWARD Plug and Play BIOS;

2. Supports Advanced Power Management Function;

3. Flash Memory for easy upgrade.

I/O Function

1. Integrated USB (Universal Serial Bus) controller with

two USB ports;

2. Supports 2 IDE channels with 4IDE devices (including

120MB IDE floppy);

3. Provides PCI IDE Bus Master function;

4. One floppy port (including 3.5", 1.2MB Mode 3

function);

5. Two high speed 16550 FIFO UART ports;

6. One parallel port with EPP/ECP/SPP capabilities;

7. PS/2 mouse connector;

8. Infrared module connector.

Other Functions

1. ATX Form Factor with 19cm x 30.5cm;

2. 4 PCI Master slots, 3 ISA slots, and 1 AGP slot;

3. Supports SCSI/CD-ROM Boot function.

Note: 1. Make sure that the SDRAM module not only has

to be 168 pin DIMM but designed for 3.3V

unbuffered SDRAM as well. Double check with

the SDRAM supplier before install any SDRAMs.

The mainboard manufacturer has no obligation to

any damage of the board by using the incorrect

specification of SDRAM.

2. Do not mix EDO and SDRAM together for the

system stability.

Introduction 3

Mainboard Setting for Pentium MMX-166

The default settings of the following figure is for the INTEL

Pentium MMX-166 with the 512K (or 256K) cache.

Intel

MMX

CPU

W83877F

ISA3

ISA2

ISA1

PCI4

PCI3

PCI2

PCI1

VT82C586B

FLASH BIOS

FDC

JP2

HD/LED IR PWR/SW

T/LEDKEYLOCKRESETSPK

AGP

IDE2

IDE1

VIA

VP3

Clock

Gen

Pipelined

SRAM

Pipelined

SRAM

CPU Fan

JP1

Off

TAG

ATX Power

SIMM1

SIMM2

DIMM1 (Bank 0)

DIMM2 (Bank 1)

DIMM3 (Bank 2)

PRT1

COM2 COM1

USB0

USB1

PS/2

K/B

Upper

Lower

Note: DIMM3 and SIMM1/2 can’t be installed simultaneously.

(Bank 2)

Figure 1–1. SL–55B5 Motherboard Layout

Chapter 2

Hardware Setup

CPU V

CORE

Voltage Setting

JP1: CPU V

Core

Voltage Setting

3.1V*

3.5V

Pentium (P54C)

6x86

VCore

Voltage

3.0V* 3.4V

2.9V

K6Ð166/200

6x86MX (M2)

3.3V

IDT C6

2.8V

MMX, 6x86L

3.2V*

K6Ð233

(or higher)

VCore

Voltage

2.4V2.0V

VCore

Voltage

2.5V

2.6V

2.7V

2.1V*

2.2V

K6Ð266

(or higher)

2.3V

VCore

Voltage

JP1 JP13 JP1 JP1

CPU Type VCore

Pentium (P54C), 6x86, K5 3.52V

IDT C6 3.3V

MMX (P55C) 2.8V

6x86L 2.8V

K6-166/200, 6x86MX (M2) 2.9V

K6-266 (or higher) 2.2V

Hardware Installation 5

Note: 1. Refer to the table above to choose the correct

voltage for the CPU everytime that you install a

CPU.

2. Make sure that your JP1 is matched with the

CPU voltage, otherwise will damage the CPU or

make the system unstable.

3. When the new CPU is announced and is not

listed on this manual, please refer to the above

table, select the correct voltage setting for it.

AGP Driver for Win95 Installation

Requirement

¥ Microsoft Windows95OSR2.1 (OSR2.0 with USB upgrade)

¥ Apollo VP3 AGP VxD Driver

¥ AGP VGA Card with Driver

¥ DirectX 5.0 DDK or SDK

Installation Procedure

Step1 Go to the next step if you are running

Win95OSR2.0/2.1, and if not, install Windows95

4.00.950B or later version

Step2 Install USBSUBB.EXE program (USB upgrade)

Step3 Install Apollo VP3 AGP VxD Driver, run

ÒSETUP.EXEÓ program

Step4 Install AGP driver for Windows95

Step5 Install Microsoft DirectX 5.0 DDK or SDK

To make sure if the Apollo VP3 AGP driver is properly

installed, boot up the system and run the ÒRegeditÓ to check

if the following path with VIAGARTD exists:

ÒHKEY_LOCAL_MACHINES\System\CurrentControlSet\

Services\VxDÓ.

Table des matières

Autres manuels SOLTEK Carte mère

SOLTEK

SOLTEK SL-75LIV Manuel utilisateur

SOLTEK

SOLTEK SL-55D5 Manuel d'utilisation et d'entretien

SOLTEK

SOLTEK SL-65MIV-C Manuel utilisateur

SOLTEK

SOLTEK B7A-F Manuel utilisateur

SOLTEK

SOLTEK SL-65ME Manuel utilisateur

SOLTEK

SOLTEK SL-855GEI-FDGR Manuel utilisateur

SOLTEK

SOLTEK SL-65LIV-T Manuel utilisateur

SOLTEK

SOLTEK SL-63AV Manuel utilisateur

SOLTEK

SOLTEK SL-PT880E-R Manuel utilisateur

SOLTEK

SOLTEK B9A-FGR Manuel utilisateur

SOLTEK

SOLTEK SL-52D2 Manuel utilisateur

SOLTEK

SOLTEK K8AV2-R Manuel utilisateur

SOLTEK

SOLTEK SL-67B-W Manuel utilisateur

SOLTEK

SOLTEK 85DIR Manuel utilisateur

SOLTEK

SOLTEK SL-65EB Manuel utilisateur

SOLTEK

SOLTEK SL-B9D-FGR Manuel utilisateur

SOLTEK

SOLTEK 75FRN2 Series Manuel utilisateur

SOLTEK

SOLTEK SL-XP865G-3IG Manuel utilisateur

SOLTEK

SOLTEK SL-67EZ Manuel d'utilisation et d'entretien

SOLTEK

SOLTEK SL-85DR-C Manuel utilisateur

SOLTEK

SOLTEK SL-75ERV Manuel utilisateur

SOLTEK

SOLTEK SL-75DRV2 Manuel utilisateur

SOLTEK

SOLTEK 85DR2-DC Manuel utilisateur

SOLTEK

SOLTEK 86SP3 Manuel utilisateur

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur