Press “mode” button in standard mode for more than 2 seconds to enter the setup mode. The active segment will start to blink.
Adjustment sequence: °C/°F → 12/24Hr → hours → minutes. To leave the adjusting mode, press “mode” button until the adjusting segments stop flashing.
Press “ +“ or “ -” button to move one step forward or backward; press these buttons longer to move forward or backward faster.
3.2 Alarm clock setting
Press “mode” button shortly to display the set alarm time. To set the alarm, hold the “mode” button longer to enter the alarm setting mode: clock → minutes →
alarm snooze. To leave the adjusting mode, press “mode” button until the adjusting segments stop flashing. If no button is pressed for 30 seconds, the device
will exit the adjusting mode and save the currently set values. To turn the alarm on or off use “on/off AL” switch on the side of the device.
3.3 Alarm sequence
Turning the alarm on or off is done using the “on/off AL” switch. The “ZZ”symbol will start flashing on the display when the alarm is triggered. If you press /
ZZwhen the alarm is triggered, its function will be put off by the pre-set time interval (1 to 60 min). To switch the alarm signal off press any other key. You can
use the snooze function as many times as you wish. When the alarm rings, no RCC signal is received; its reception will be resumed once the alarm is turned off.
The alarm signal will automatically turn off after two minutes. The alarm sequence is as follows: a) 0-10 seconds: one beep per second; b) 10-20 seconds: two
beeps per second; c) after 20 seconds: three beeps per second.
3.4 Sensor switching function
In standard mode, you can toggle between the channels by pressing the “CH” button (CH1, CH2, CH3 or cycling between all three channels). When cycling, the
symbol will appear on the display. In three-channel cycling display mode, the values will change automatically. If less than three outdoor sensors are
connected, no data is displayed when cycling through unconnected channels.
3.5 Sensor pairing function
First of all, a different channel must be set on the various sensors. Open the battery cover and set channel number 1, 2 or 3 using the position switch. Then insert
batteries and close the cover. When switching the weather station on for the first time, the sensors will be paired automatically. However, if you want to change
the pairing, switch the channel using the “CH” button and then hold it for at least three seconds. Pairing will take about three minutes. If the pairing fails, the
weather station is probably out of the signal range.
3.6 Receiving RCC control signal
Receiving the RCC signal will start automatically after starting or resetting.
Forced RCC signal reception: hold the “–wave” button.
When the signal reception is turned on, a three-minute long synchronization will start. During synchronization, you cannot enter any functions; the
weather station is not performing any measurements now, the USB power outlet is also deactivated.
Automatic signal reception every day.
Automatic reception will take place at the following daily times: 1:00, 2:00 and 3:00. In case of a failure, the signal reception attempt will be repeated at
4:00 and 5:00. If the signal is successfully received at 4:00, no further reception will take place for the given day. If the signal reception at 4:00 fails, it will be
repeated at 5:00 and, regardless of whether successful or not, it will not be repeated for the given day. The control signal reception process lasts 7 minutes.
The icon will flash in the RCC signal reception mode.
If the signal is weak or if the device is unable to recognize correct signal, the tower symbol will flash but no radio wave symbol will appear.
If the control signal has been successfully received, the full RCC reception icon will illuminate and the device will exit the signal reception mode.
To exit the reception mode, briefly press the “–wave” button.
If alarm is activated in the RCC signal reception mode, the device will exit the reception mode and enter the alarm mode.
After receiving the DST signal, a DST icon will be displayed.
After resetting, and DST symbols will disappear.
3.7 Weather forecast function
The weather station generates a weather forecast for the next 8 hours. The measurement is based on monitoring the pressure trend. The forecast information is
for reference only. This weather station cannot be compared with professional computer equipment. For objective forecast, refer to official sources.
Six levels of graphic weather forecast:
3.8 Display light
If the weather station is running on batteries, pressing the /ZZtouch sensor will illuminate the display for 8 seconds. If the display backlight is weak,
replace the batteries. When running on power adapter, the display may be lit constantly (depending on the backlight intensity setting).
3.9 Display backlight colour setting
Briefly press the “rainbow” button to set different background colours (white, red, orange, yellow, green, blue-green, blue and purple). When running on power
adapter mode, press the “ - ” button to adjust the backlight intensity. If you press the “loop” button, the display backlight colours will change sequentially. If you
press the “loop” button again, the display will remain lit with the current colour.
A CE Declaration of Conformity is issued to the product in accordance with applicable regulations. On request from the manufacturer: info@solight.cz, or to
download at https://www.solight.cz/documents/te86_prohlášení o shodě.pdf
The maximum radiated power of the device in the working frequency band 433.92MHz is 10mW (+ 10dbm).
Producer: Solight Holding, s.r.o., Na Brně 1972, Hradec Kralove 500 06, Czech Republic.
