SnowEx SP-100-1 Manuel utilisateur

This document supersedes all editions with an earlier date.

January 1, 2017

Lit. No. 75312, Rev. 00

SP-100-1 & SP-125-1

Tailgate Spreader

Owner's Manual and Installation Instructions

Original Instructions

This manual is for SnowEx®SP-100-1 & SP-125 -1 tailgate spreaders with

serial numbers beginning with 170109 and higher.

CAUTION

Read this manual before installing or

operating the spreader.

Lit. No. 75312, Rev. 00 3 January 1, 2017

TABLE OF CONTENTS

INTRODUCTION......................................................... 4

Owner's Information Form ....................................4

SAFETY INFORMATION............................................ 5

LOADING.................................................................... 9

Certiﬁcation........................................................... 9

Approximate Material Weights.............................. 9

MOUNTING THE SPREADER ................................. 10

Assembly Instructions......................................... 10

Receiver Mount Spreader................................... 10

WIRING INSTRUCTIONS......................................... 12

ELECTRICAL DIAGRAMS

Model SP-100-1 .................................................. 13

Model SP-125-1 .................................................. 16

OPERATING THE SPREADER................................ 17

Driving and Spreading on Snow and Ice ............ 17

Spreading Tips.................................................... 17

REMOVING THE SPREADER ................................. 18

MAINTENANCE........................................................ 19

Lubrication .......................................................... 19

After Each Use.................................................... 19

At the End of Each Season or after

Extended Storage............................................ 19

Storage ............................................................... 19

TROUBLESHOOTING.............................................. 20

Lit. No. 75312, Rev. 00 4 January 1, 2017

INTRODUCTION

This manual has been prepared to acquaint you with

the safety information, operation and maintenance of

your new tailgate spreader. Please read this manual

carefully and follow all recommendations. This will

help ensure proﬁtable and trouble-free operation of

your tailgate spreader. Keep this manual accessible. It

is a handy reference in case minor service is required.

When service is necessary, bring your spreader to

your distributor. They know your spreader best and are

interested in your complete satisfaction.

NOTE: This spreader is designed to spread snow

and ice control materials only. Do not use it

for purposes other than those speciﬁed in this

manual.

Warranty Registration

Follow the directions on the SnowEx®Warranty

Registration and Customer Survey form included in

the spreader literature kit.

The registration form is also available online at

www.snowexproducts.com. Under "Support" select

"Warranty Registration."

OWNER'S INFORMATION

Owner's Name: ______________________________________________________________________

Date Purchased: _____________________________________________________________________

Distributor Name: __________________________________________ Phone:_________________

Distributor Address:___________________________________________________________________

Vehicle Model: _____________________________________________ Year: __________________

Spreader Model: _________________________ Serial #:__________________________________

Spreader Weight:_____________________lb/kg

Lit. No. 75312, Rev. 00 5 January 1, 2017

SAFETY DEFINITIONS

NOTE: Indicates a situation or action that can lead

to damage to your spreader and vehicle or other

property. Other useful information can also be

described.

SAFETY INFORMATION

WARNING/CAUTION LABELS

Please become familiar with the Warning and Caution

labels on the spreader.

NOTE: If labels are missing or cannot be read, see

your sales outlet.

CAUTION

Indicates a potentially hazardous situation

that, if not avoided, may result in minor or

moderate injury. It may also be used to alert

against unsafe practices.

WARNING

Indicates a potentially hazardous situation

that, if not avoided, could result in death or

serious personal injury.

Lit. No. 75312, Rev. 00 6 January 1, 2017

SAFETY INFORMATION

SERIAL NUMBER LABEL

Code Deﬁnition

YY 2-Digit Year

MM 2-Digit Month

DD 2-Digit Day

LL 2-Digit Location Code

XXXX 4-Digit Sequential Number

ZZZZZZ Assembly Part Number

Model No. 00000

Serial No. YYMMDDLLXXXXZZZZZZ

Model No. 00000

Serial No. 000000000000000000

Lit. No. 75312, Rev. 00 7 January 1, 2017

CAUTION

Disconnect electric and/or hydraulic power

and tag out if required before servicing or

performing maintenance.

CAUTION

DO NOT leave unused material in

hopper. Material can freeze or solidify,

causing unit to not work properly.

Empty and clean after each use.

NOTE: Lubricate grease ﬁttings after each use.

Use a good quality multipurpose grease.

PERSONAL SAFETY

• Remove ignition key and put the vehicle in park or

in gear to prevent others from starting the vehicle

during installation or service.

• Wear only snug-ﬁtting clothing while working on

your vehicle or spreader.

• Do not wear jewelry or a necktie, and secure long

hair.

• Wear safety goggles to protect your eyes from

battery acid, gasoline, dirt and dust.

• Avoid touching hot surfaces such as the engine,

radiator, hoses and exhaust pipes.

• Always have a ﬁre extinguisher rated BC handy,

for ﬂammable liquids and electrical ﬁres.

SAFETY INFORMATION

SAFETY PRECAUTIONS

Improper installation and operation could cause

personal injury and/or equipment and property

damage. Read and understand labels and the

Owner's Manual before installing, operating or making

adjustments.

WARNING

• Driver to keep bystanders minimum of

25 feet away from operating spreader.

• Before working with the spreader, secure all

loose-ﬁtting clothing and unrestrained hair.

• Before operating the spreader, verify all

safety guards are in place.

• Before servicing the spreader, wait for

auger and spinner to stop.

• Do not climb into or ride on spreader.

WARNING

Overloading could result in an

accident or damage. Do not exceed

GVWR or GAWR ratings as found on

the driver-side door cornerpost of

the vehicle. See Loading Section to determine

maximum volumes of spreading material.

CAUTION

If rear directional, CHMSL light or brake

stoplights are obstructed by the spreader,

the lights shall be relocated, or auxiliary

directional or brake stoplights shall be

installed.

CAUTION

During the hopper spreader installation

we recommend the addition of an OSHA

compliant Backup Alarm. This alarm is

required for OSHA governed employers.

CAUTION

• Do not operate a spreader in need of

maintenance.

• Before operating the spreader, reassemble

any parts or hardware removed for cleaning

or adjusting.

• Before operating the spreader, remove

materials such as cleaning rags, brushes,

and hand tools from the spreader.

• While operating the spreader, use auxiliary

warning lights, except when prohibited by law.

• Tighten all fasteners according to the

Torque Chart. Refer to Torque Chart for the

recommended torque values.

Lit. No. 75312, Rev. 00 8 January 1, 2017

VENTILATION

BATTERY SAFETY

FIRE AND EXPLOSION

Be careful when using gasoline. Do not use gasoline

to clean parts. Store only in approved containers away

from sources of heat or ﬂame.

CELL PHONES

A driver's ﬁrst responsibility is the safe operation of

the vehicle. The most important thing you can do

to prevent a crash is to avoid distractions and pay

attention to the road. Wait until it is safe to operate

Mobile Communication Equipment such as cell phones,

text messaging devices, pagers or two-way radios.

CAUTION

Batteries normally produce explosive gases

which can cause personal injury. Therefore,

do not allow ﬂames, sparks or lit tobacco

to come near the battery. When charging or

working near a battery, always cover your

face and protect your eyes, and also provide

ventilation.

• Batteries contain sulfuric acid which burns

skin, eyes and clothing.

• Disconnect the battery before removing or

replacing any electrical components.

WARNING

Vehicle exhaust contains lethal fumes.

Breathing these fumes, even in low

concentrations, can cause death. Never

operate a vehicle in an enclosed area without

venting exhaust to the outside.

WARNING

Gasoline is highly ﬂammable and gasoline

vapor is explosive. Never smoke while

working on vehicle. Keep all open ﬂames

away from gasoline tank and lines. Wipe up

any spilled gasoline immediately.

SAFETY INFORMATION

CAUTION

Read instructions before assembling.

Fasteners should be ﬁnger tight until

instructed to tighten according to torque

chart. Use standard methods and practices

when attaching spreader including proper

personal protective safety equipment.

TORQUE CHART

1/4-20 109 154

1/4-28 121 171

5/16-18 150 212

5/16-24 170 240

3/8-16 269 376

3/8-24 297 420

7/16-14 429 606

7/16-20

9/16-12

9/16-18

5/8-11

5/8-18

3/4-10

3/4-16

7/8-9

7/8-14 474 669

644 9091-8

1-12 704 995

1/2-13

1/2-20

11.9

13.7

24.6

27.3

43.6

26.9

53.3

148

49.4

69.8

77.9

106.4

120.0

8.4

9.7

17.4

19.2

30.8

35.0

49.4

55.2

75.3

85.0

M6 x 1.00

M12 x 1.75

M8 x 1.25

M14 x 2.00

M10 x 1.50

M27 x 3.00

M22 x 2.50

M30 x 3.50

M24 x 3.00

M20 x 2.5011.1

19.5

38.5

107

7.7

613

778

1139

1545

450

428

562

796

1117

M33 x 3.50

M36 x 4.00

2101

2701

1468

1952

325

M16 x 2.00 231

167

M18 x 2.50 318222

Recommended Fastener Torque Chart

Size Size

Torque (ft-lb)

Grade

Metric Fasteners Class 8.8 and 10.9

These torque values apply to fasteners

except those noted in the instructions.

Torque (ft-lb)

Grade

Size Size

Torque (ft-lb)

Class

8.8

Class

10.9

Torque (ft-lb)

Class

8.8

Class

10.9

Inch Fasteners Grade 5 and Grade 8

NOISE

Airborne noise emission during use is below 70 dB(A)

for the spreader operator.

VIBRATION

Operating snowplow vibration does not exceed

2.5 m/s2to the hand-arm or 0.5 m/s2to the whole

body.

Lit. No. 75312, Rev. 00 9 January 1, 2017

APPROXIMATE MATERIAL WEIGHTS

Material Density

(lb/ft3)

Rock Salt (Dry) 80–90

Weight of spreader and mount must be added

to struck material weight to determine total

spreader weight. Do not exceed maximum

material capacity as shown on the safety label

(see Safety Information section).

Use only bagged rock salt with the spreader.

Other forms of spreading material are not

compatible with the tailgate spreader.

NOTE: If spreader and ice control material loading

is in doubt, weigh vehicle for compliance with

vehicle ratings.

This manual covers vehicles which have been

recommended for carrying the spreader. Please see

your local dealer for proper vehicle applications.

CERTIFICATION

WARNING

Overloading could result in an accident or

damage. Do not exceed GVWR or GAWR

as found on the driver-side cornerpost of

vehicle.

WARNING

New untitled vehicle installation of a spreader

requires National Highway Trafﬁc Safety

Administration altered vehicle certiﬁcation

labeling. Installer to verify that struck load of

snow or ice control material does not exceed

GVWR or GAWR rating label and complies

with FMVSS.

CAUTION

Read and adhere to manufacturer's

ice-control material package

labeling including Material Safety

Data Sheet requirements.

WARNING

Do not overload vehicle. Use chart below

to calculate weight of material. Weights of

material are an average for dry materials.

CAUTION

Never use wet materials or materials with

foreign debris with any of these spreaders.

These units are designed to handle dry, clean,

free ﬂowing material.

Lit. No. 75312, Rev. 00 10 January 1, 2017

ASSEMBLY INSTRUCTIONS

The spreader shall be installed according to

instructions supplied. Your local outlet is trained to

provide this service and service your spreader with

factory original parts.

1. Place the drive assembly on a ﬂat, level surface.

Attach the receiver mount to the drive assembly

as shown below using four 1/2" x 1-1/2" cap

screws. Tighten the fasteners according to the

torque chart.

2. Mount the support frame to the drive assembly

using the six supplied 5/16" x 1" cap screws and

the four supplied 5/16" locknuts. Tighten the

fasteners according to the torque chart.

MOUNTING THE SPREADER

3. Mount the throat support to the support frame at

the two lower holes by using the four supplied

5/16" x 1" cap screws and 5/16" locknuts. Tighten

the fasteners according to the torque chart.

Support Frame

5/16" Locknuts

5/16" x 1" Cap Screws

Drive Assembly

Receiver Mount

1/2" x 1-1/2"

Cap Screw

5/16"

Locknut 5/16" x 1"

Cap Screw

Support

Frame

Throat Support

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels SnowEx Épandeur

SnowEx

SnowEx SP-225-1 Mode d'emploi

SnowEx

SnowEx SP-1675 Manuel utilisateur

SnowEx

SnowEx SP-100 Manuel du propriétaire

SnowEx

SnowEx SP-85 Manuel du propriétaire

SnowEx

SnowEx SP-65 Manuel du propriétaire

SnowEx

SnowEx SP-8550 Manuel du propriétaire

SnowEx

SnowEx V-Maxx G2 VX-6010 Manuel utilisateur

SnowEx

SnowEx Tailgate Pro 575X Manuel utilisateur

SnowEx

SnowEx Bulk Pro SP-1575 Mode d'emploi

SnowEx

SnowEx SP-3000 Manuel utilisateur

SnowEx

SnowEx Vee Pro 3000 Manuel utilisateur

SnowEx

SnowEx SP-7000 Manuel utilisateur

SnowEx

SnowEx HELIXX Manuel utilisateur

SnowEx

SnowEx VX-3210 Manuel utilisateur

SnowEx

SnowEx Bulk Pro 1575 Manuel utilisateur

SnowEx

SnowEx SP-2400 Manuel du propriétaire

SnowEx

SnowEx SP-85 Mode d'emploi

SnowEx

SnowEx SP-575V Manuel du propriétaire

SnowEx

SnowEx K1-131116 Manuel du propriétaire

SnowEx

SnowEx SR-210 Mode d'emploi

SnowEx

SnowEx SP-65 Mode d'emploi

SnowEx

SnowEx 7500 Manuel utilisateur

SnowEx

SnowEx VX-6010 Manuel utilisateur

SnowEx

SnowEx Super Maxx SP-9300XH Mode d'emploi

Manuels Épandeur populaires d'autres marques

PEQUEA

PEQUEA GT-100 Manuel utilisateur

Herculano

Herculano H2RS9 Manuel utilisateur

Epoke

Epoke SKE8 Manuel utilisateur

GEA

GEA EL44 Fiche technique

Boss Snowplow

Boss Snowplow TGS 800 Manuel utilisateur

Fisher

Fisher EMERSON 168 Series Manuel utilisateur

Fisher

Fisher POLY-CASTER 78601 Manuel utilisateur

TurfEx

TurfEx RS7200 Manuel du propriétaire

Ferris

Ferris Pathfinder Series Manuel utilisateur

Fayat Group

Fayat Group DYNAPAC S100 Guide de dépannage

Art's-Way Manufacturing

Art's-Way Manufacturing X700 Manuel d'installation et d'exploitation

EASTMAN

EASTMAN CR 500 Manuel utilisateur

Nogueira

Nogueira RoyalFlow-600 Manuel utilisateur

Buyers

Buyers TGS05B Manuel utilisateur

Magnum

Magnum V-BOX PV Series Supplément

Meyer's

Meyer's VB280 Manuel utilisateur

Kramer

Kramer VM-400HDCP Manuel utilisateur

H&S

H&S 5134 Manuel utilisateur