Smeg FU65-5 Manuel utilisateur

Table of Contents

1. IMPORTANT SAFETY INSTRUCTIONS ................................................................................. 4

2. GENERAL INSTALLATION INSTRUCTIONS ......................................................................... 5

3. PREPARE BUILT–IN OVEN .................................................................................................... 6

4. MAKE ELECTRICAL CONNECTION ...................................................................................... 8

NOTE: THIS APPLIANCE MUST BE INSTALLED SOLELY AND EXCLUSIVELY BY A QUALIFIED

TECHNICIAN. ANY TECHNICAL PROCEDURES MUST BE CARRIED OUT BY AN AUTHORIZED

TECHNICIAN.

INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified engineer who is able to

install, commission and test the appliance

Important Safety Instruction

1. IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS – Your Safety And the Safety of Others Are Very Important.

We have provided many important safety messages throughout this manual and on your appliance.

Read all instructions before using your appliance and always obey all safety messages.

RECOGNIZE SAFETY INFORMATION

This is a safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and

others.

UNDERSTAND SIGNAL WORDS

A signal word – DANGER, WARNING, or CAUTION – is used with the safety-alert symbol. DANGER

identifies the most serious hazards. It means you can be killed or seriously injured if you do not

immediately follow instructions. WARNING means you can be killed or seriously injured if you do not

follow instructions. CAUTION indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

All safety messages will inform you as to potential hazards, inform you on how to reduce the risk of

injury and as to what can occur if the instructions are not followed.

IMPORTANT: Installation and grounding must comply with applicable codes. Observe all

government codes and ordinances.

WARNING

- This appliance is intended for household use only.

- Only use the appliance for its intended purpose. The manufacturer cannot be

held responsible for damages caused by improper use of this oven.

- This appliance complies with current safety requirements. Improper use of the

appliance can lead to personal injury and material damage.

- Read all instructions before installing or using the oven for the first time.

- Keep these operating instructions in a safe place and pass them on to any

further user.

SAVE THESE INSTRUCTIONS

FOR THE LOCAL INSPECTORS USE

Important Safety Instruction

2. GENERAL INSTALLATION INSTRUCTIONS

•Proper installation is your responsibility. Have a qualified technician install this oven. Make sure

you have everything necessary for correct installation. It is responsibility of the installer to comply

with the installation clearances specified on the model/serial rating plate. The model/serial rating

plate can be found on the internal frame of the oven, once you open the door.

•Have your oven installed and properly grounded by a qualified installer, in accordance with

these installation instructions. Grounding is mandatory according to the provisions of the

electrical system safety regulations. If this appliance is connected to an outside electrical power

source, it must be grounded in compliance with local laws, or, if non exsist, in compliance with the

national ANSI / NFPA 70 code of electrical regulations.

• Make sure that the voltage and dimensions of the supply line correspond to the characteristics

indicated on the model/serial rating plate.

• Do not attempt to repair or replace any part of your oven unless it is specifically recommended in this

manual. All other service procedures should be performed by a qualified technician.

• This oven is not suitable for assembly and use in mobile homes or campers.

•Electrical grounding is required. See the “Make Electrical Connection” section. It is the customer’s

responsibility:

- To contact a qualified electrical installer,

- To ensure that the electrical system is adequate and in conformance with the national ANSI /

NFPA 70 ELECTRICAL CODE – Latest edition – Or the CSA STANDARDS C22.1-94,

CANADIAN ELECTRICAL CODE, PART 1 AND CSA C22.2 No. O-91 – or latest edition – and

all local codes and ordinances. IMPORTANT: Observe all governing codes and ordinances.

Instructions for the Installer

3. PREPARE BUILT–IN OVEN

WARNING

EXCESSIVE WEIGHT HAZARD

- Use two or more people to move and install the oven

- Failure to do so can result in back or other injury.

IMPORTANT: This appliance must be integrated in any cabinets made of material which is heat resistant

up to temperatures of 194°F-90°C.

Keep to the dimensions indicated in pictures 1, 2, 3. For under-worktop positioning, keep to the

dimensions indicated in pictures 1 and 3. For column positioning, keep to the dimensions indicated in

pictures 1 and 2.

Make sure the 2 spacers “A” are fitted inside the cornice.

Remember that the upper/rear part of the cabinet must have an opening with a depth of 3 1/8” - 3 1/2” /

80 – 90 mm for proper air ventilation. The same opening must be guaranteed also in the rear/lower part

of the cabinet in under worktop installation, as shown in part Bof pictures no. 1.

Instructions for the Installer

It is important to follow these instructions before and during the oven installation:

• Decide the final location of the oven. Locate exsisting wiring to avoid drilling into or severing wiring

during installation.

• To avoid floor damage, set the oven onto cardboard prior to installation. Do not use handle or any

portion of the frame or trim for lifting.

• Remove the shipping materials and tape from the oven.

• Remove the literature contained in the package.

• Remove and set aside racks and other parts from inside the oven.

• Move oven and cardboard close to the oven’s final location.

• Remove oven door (see paragraph “8.2 Removing the door” in the Instruction for the User booklet)

IMPORTANT: Use both hands to remove the oven door.

Instructions for the Installer

4. MAKE ELECTRICAL CONNECTION

WARNING

ELECTRIC SHOCK HAZARD

- Disconnect power to the junction box before making connection

- Electrically ground the appliance with green or green-yellow colored

wire

FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN DEATH,

FIRE OR SHOCK.

This appliance is manufactured with a yellow and green or green ground wire connected to the oven

chassis.

To prepare connection between the oven and the junction box:

- Disconnect power supply to the junction box,

- Feed the flexible cable conduit from the oven through the opening of the cabinet,

- Remove junction box cover if it is present,

- Install UL listed and CSA approved conduit connector to the junction box,

- Route the flexible cable conduit from the oven to the junction box through a UL listed or CSA

approved conduit connector.

- Tighten screws on conduit connector,

- Refer to figures 1 and 2 below, which represent the most common way of making electrical

connection.

IMPORTANT: Your eventual local codes and ordinances must be followed first to the instructions.

NOTE: Frame grounded by connection of grounding wire to neutral wire. If used in new branch circuit

installation (1996 NEC) or if local codes do not permit grounding through neutral wire, open the

connection and use grounding wire to ground unit in accordance with local codes. Connect neutral wire

to the branch circuit’s neutral conductor in the usual manner:

- Disconnect the ground from the neutral at free end of conduit,

- Use grounding terminal or lead to ground unit, and

- Connect neutral terminal or wire to branch circuit neutral in usual manner (see pic. 2 below)

Instructions for the Installer

US INSTALLATION ONLY–3–WIRE BRANCH CIRCUIT

Refer to picture 1, where local codes allow the

connection of ground wire from the applliance to

the branch circuit neutral wire (white colored wire):

- The ground wire must be attached first;

- If local codes permit, connect the green or

yellow-green ground wire from the appliance

and the white wire from the appliance to the

branch circuit neutral wire (white colored wire).

- Connect the red and black leads from the oven

to the junction using a UL/CSA listed wire

connectors to the corresponding leads in the

junction box. pic.1)

US INSTALLATION AND CANADIAN INSTALLATION–4–WIRE BRANCH CIRCUIT

Refer to picture 2,

- Disconnect the green or yellow green from the

white lead;

- The ground wire must be attached first;

- Connect the green or yellow-green ground wire

from the appliance to the ground in the junction

box (green colored wire) using a UL/CSA listed

wire connectors. Do not connect grounding

wire to neutral wire in junction box.

- Connect the red and black leads from the

appliance to the corresponding leads in the

junctionbox using a UL/CSA listed wire

connectors

- Connect the white wire from the appliance to the

neutral (white colored wire) wire in the junction

box using a UL/CSA listed wire connectors.

pic.2)

Connect to a 20A fuse or circuit breaker. Connect to copper wire only or if connecting to

aluminium house wire use UL listed or CSA approved connectors, which are suitable for joining

aluminium with copper wires.

UL/CSA

listed wire

connector

UL/CSA

listed wire

connector

Autres manuels pour FU65-5

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Smeg Four

Smeg

Smeg SA109-8 Manuel utilisateur

Smeg

Smeg SC45VK Manuel utilisateur

Smeg

Smeg SC855A-8 Manuel utilisateur

Smeg

Smeg SA561X-9 Manuel utilisateur

Smeg

Smeg SC0468X-8 Manuel utilisateur

Smeg

Smeg F166-5 Manuel utilisateur

Smeg

Smeg Four Oven Manuel du système

Smeg

Smeg SAC399X-8 Manuel utilisateur

Smeg

Smeg SF465N Manuel utilisateur

Smeg

Smeg SCA712-3 Manuel utilisateur

Smeg

Smeg SO4303APX Manuel utilisateur

Smeg

Smeg SOP6900TX Manuel utilisateur

Smeg

Smeg Oven Manuel utilisateur

Smeg

Smeg SCV38X Manuel utilisateur

Smeg

Smeg ALFA135BM Manuel utilisateur

Smeg

Smeg SF700BS Manuel utilisateur

Smeg

Smeg SFA4920MCB Manuel utilisateur

Smeg

Smeg SA240X-5 Manuel utilisateur

Smeg

Smeg Oven Manuel utilisateur

Smeg

Smeg Oven Mode d’emploi

Smeg

Smeg SFP105 Manuel utilisateur

Smeg

Smeg Multi-Function Built-In Oven Manuel utilisateur

Smeg

Smeg SF166 Manuel utilisateur

Smeg

Smeg Oven Manuel utilisateur

Manuels Four populaires d'autres marques

Bosch

Bosch HVA531NS0 Manuel utilisateur

Electrolux

Electrolux EOF6P46X Manuel utilisateur

NEFF

NEFF B44S32 5GB Series Manuel utilisateur

Combi

Combi BLODGETT BC142GDS Manuel utilisateur

AEG

AEG COMPETENCE 311704300 Manuel utilisateur

Falcon

Falcon DOMINATOR PLUS G3106 Series Guide de l'utilisateur

Rational

Rational SCC WE 61G Manuel utilisateur

Electrolux

Electrolux air-o-convect 20 GN 2/1 Manuel utilisateur

Miele

Miele HR 1954-2 Manuel utilisateur

KHIND

KHIND OT50 Manuel utilisateur

Henny Penny

Henny Penny Smoker Box Manuel utilisateur

Lang

Lang ECOD-AP Manuel utilisateur

AEG

AEG BEK455310M Manuel utilisateur

Frigidaire

Frigidaire FNGE90JGR Manuel utilisateur

Hotpoint

Hotpoint FE9 S831 JSH IX Manuel utilisateur

GE Advantium SCB2000 Manuel utilisateur

AEG

AEG DE401301DM Manuel utilisateur

DeLonghi

DeLonghi XA660 Manuel