SMC Networks 8028L2 Manuel utilisateur
INSTALLATION GUIDE
ta
TigerSwitchTM 10/100/1000
28-Port Gigabit Ethernet Switch
SMC8028L2
20 Mason
Irvine, CA 92618
Phone: (949) 679-8000
TigerSwitch 10/100/1000
Installation Guide
From SMC's Tiger line of feature-rich workgroup LAN solutions
Janurary 2010
Pub. # 150200000155A
E012010-MW-R01
20 Mason
Irvine, CA 92618
Phone: (949) 679-8000
Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and
reliable. However, no responsibility is assumed by SMC for its use, nor for any
infringements of patents or other rights of third parties which may result from its use. No
license is granted by implication or otherwise under any patent or patent rights of SMC.
SMC reserves the right to change specifications at any time without notice.
Copyright © 2010 by
SMC Networks, Inc.
20 Mason
Irvine, CA 92618
All rights reserved. Printed in China
Trademarks:
SMC is a registered trademark; and EZ Switch, TigerStack and TigerSwitch are
trademarks of SMC Networks, Inc. Other product and company names are trademarks or
registered trademarks of their respective holders.
W
ARRANTY
AND
P
RODUCT
R
EGISTRATION
To register SMC products and to review the detailed warranty statement,
please refer to the Support Section of the SMC Website at http://
www.smc.com.
– 5 –
COMPLIANCES AND SAFETY
STATEMENTS
FCC - CLASS A
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the
interference at his own expense.
You are cautioned that changes or modifications not expressly approved by the
party responsible for compliance could void your authority to operate the
equipment.
You may use unshielded twisted-pair (UTP) for RJ-45 connections - Category 3
or better for 10 Mbps connections, Category 5 or better for 100 Mbps
connections, Category 5, 5e, or 6 for 1000 Mbps connections. For fiber optic
connections, you may use 50/125 or 62.5/125 micron multimode fiber or 9/125
micron single-mode fiber.
C
OMPLIANCES
AND
S
AFETY
S
TATEMENTS
– 6 –
CE MARK DECLARATION OF CONFORMANCE FOR EMI AND SAFETY (EEC)
This information technology equipment complies with the requirements of the
Council Directive 89/336/EEC on the Approximation of the laws of the Member
States relating to Electromagnetic Compatibility and 73/23/EEC for electrical
equipment used within certain voltage limits and the Amendment Directive 93/
68/EEC. For the evaluation of the compliance with these Directives, the following
standards were applied:
RFI Emission: ◆Limit class A according to EN 55022
◆Limit class A for harmonic current emission according to EN 61000-3-
2
◆Limitation of voltage fluctuation and flicker in low-voltage supply
system according to EN 61000-3-3
Immunity: ◆Product family standard according to EN 55024
◆Electrostatic Discharge according to EN 61000-4-2
◆Radio-frequency electromagnetic field according to EN 61000-4-3
◆Electrical fast transient/burst according to EN 61000-4-4
◆Surge immunity test according to EN 61000-4-5
◆Immunity to conducted disturbances, Induced by radio-frequency
fields: EN 61000-4-6
◆Power frequency magnetic field immunity test according to EN 61000-
4-8
◆Voltage dips, short interruptions and voltage variations immunity test
according to EN 61000-4-11
LVD: ◆EN 60950-1:2001
C
OMPLIANCES
AND
S
AFETY
S
TATEMENTS
– 7 –
SAFETY COMPLIANCE
Warning: Fiber Optic Port Safety
Avertissment: Ports pour fibres optiques - sécurité sur le plan optique
Warnhinweis: Faseroptikanschlüsse - Optische Sicherheit
PSE ALARM
本製品に同梱いたしております電源コードセットは、
本製品専用です。本電源コードセットは、本製品以外の
製品並びに他の用途でご使用いただくことは出来ません。
製品本体に同梱された電源コードセットを利用し、他製品
の電源コードセットを使用しないで下さい。
When using a fiber optic port, never look at the transmit
laser while it is powered on. Also, never look directly at the
fiber TX port and fiber cable ends when they are powered
on.
Ne regardez jamais le laser tant qu'il est sous tension. Ne
regardez jamais directement le port TX (Transmission) à
fibres optiques et les embouts de câbles à fibres optiques
tant qu'ils sont sous tension.
Niemals ein Übertragungslaser betrachten, während dieses
eingeschaltet ist. Niemals direkt auf den Faser-TX-Anschluß
und auf die Faserkabelenden schauen, während diese
eingeschaltet sind.
CLASS I
LASER DEVICE
DISPOSITIF LASER
DE CLASSE I
LASERGER
DER KLASSE I
ÄT
C
OMPLIANCES
AND
S
AFETY
S
TATEMENTS
– 8 –
POWER CORD SAFETY
Please read the following safety information carefully before installing
the switch:
WARNING:
Installation and removal of the unit must be carried out by qualified
personnel only.
◆The unit must be connected to an earthed (grounded) outlet to comply with
international safety standards.
◆Do not connect the unit to an A.C. outlet (power supply) without an earth
(ground) connection.
◆The appliance coupler (the connector to the unit and not the wall plug) must
have a configuration for mating with an EN 60320/IEC 320 appliance inlet.
◆The socket outlet must be near to the unit and easily accessible. You can
only remove power from the unit by disconnecting the power cord from the
outlet.
◆This unit operates under SELV (Safety Extra Low Voltage) conditions
according to IEC 60950. The conditions are only maintained if the
equipment to which it is connected also operates under SELV conditions.
France and Peru only
This unit cannot be powered from IT†supplies. If your supplies are of IT type,
this unit must be powered by 230 V (2P+T) via an isolation transformer ratio
1:1, with the secondary connection point labelled Neutral, connected directly to
earth (ground).
†Impédance à la terre
I
MPORTANT
!
Before making connections, make sure you have the correct cord
set. Check it (read the label on the cable) against the following:
Autres manuels pour 8028L2
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels SMC Networks Changer
SMC Networks
SMC Networks IS3000-02 Manuel
SMC Networks
SMC Networks D 7K Series Manuel utilisateur
SMC Networks
SMC Networks ISE70G-N02-L2 Manuel utilisateur
SMC Networks
SMC Networks ISE70G L2 Series Manuel utilisateur
SMC Networks
SMC Networks TigerSwitch 10 Manuel utilisateur
SMC Networks
SMC Networks PFM3 Series Manuel utilisateur
SMC Networks
SMC Networks TigerSwitch SMC6709L2 Manuel utilisateur
SMC Networks
SMC Networks 6152PL2 FICHE Manuel de programmation
SMC Networks
SMC Networks EZ Networking SMC-EZ108FDT Manuel utilisateur
SMC Networks
SMC Networks 8024L2 - FICHE TECHNIQUE Guide d'installation
SMC Networks
SMC Networks D-F6# Series Manuel utilisateur
SMC Networks
SMC Networks EZ HUB 10/100 5608DS Manuel utilisateur
SMC Networks
SMC Networks ISE40A Manuel utilisateur
SMC Networks
SMC Networks TigerSwitch SMC6624M Manuel de programmation
SMC Networks
SMC Networks ZSE3 Series Manuel utilisateur
SMC Networks
SMC Networks ZSE1 Series Manuel utilisateur
SMC Networks
SMC Networks SMC8724-10BT Manuel utilisateur
SMC Networks
SMC Networks SMC6724L3 Manuel utilisateur
SMC Networks
SMC Networks TigerAccess EE SMC7816M/VSW Manuel utilisateur
SMC Networks
SMC Networks IS1000 Series Manuel utilisateur
