SMC Networks Barricade SMC7401BRA Manuel utilisateur

Re-Burn FLASH with USB connection/Reset to factory Defaults

1Power off the CPE, remove case and short the jumper J4. Jumper J4 is

right beside the USB connector.

2Power up the CPE and connect the USB to a host PC running in pure

DOS environment.

3Change directory to where you place the USB FLASH burner utility, for

example,C:\SMC7401BRA1.10.

4Execute the batch file FLASH.BAT

5Wait for a couple of seconds to complete the FLASH programming. DO

NOT power off the CPE while programming is still on going. If it fails due to

this, just redo it.Note: During the FLASH programming you will be asked

for a Start and End MAC address. Just leave both blank and press enter.

6After the FLASH programming has completed power OFF CPE. Remove

J4 and power ON.Note: Do not unplug the USB cable for the minute.

7After power ON leave the CPE for 2 minutes. After 2 minutes unplug USB

cable. You will see the USB LED go out and hear a clicking sound. The

CPE is now updated to the latest firmware & reset to factory defaults.

Notes: If you run FLASH.BAT and the USB fails to initialise try on another

USB port. If this does not work the FLASH utility is not compatible with the

USB controller on the PC. Try another brand PC.

The FLASH.BAT utility is designed to work on a FAT partition. If you execute

from an NTFS partition you may have problems.

Autres manuels pour Barricade SMC7401BRA

5

Ce manuel convient aux modèles suivants

1

Table des matières

Autres manuels SMC Networks Routeur réseau

SMC Networks

SMC Networks TIGERSWITCH 10/100 Manuel de programmation

SMC Networks

SMC Networks SMC6752AL2 Manuel utilisateur

SMC Networks

SMC Networks 7901BRA2 Manuel utilisateur

SMC Networks

SMC Networks Barricade SMC7904BRA Manuel utilisateur

SMC Networks

SMC Networks FS8 - FICHE TECHNIQUE Instructions d'utilisation et de sécurité

SMC Networks

SMC Networks GS1601 Manuel utilisateur

SMC Networks

SMC Networks EZ Switch SMCGS5 Manuel utilisateur

SMC Networks

SMC Networks 7004VBR Manuel utilisateur

SMC Networks

SMC Networks Barricade ADSL2/2+ Modem Router SMC7901BRA2 Manuel utilisateur

SMC Networks

SMC Networks GS1601 Manuel utilisateur

SMC Networks

SMC Networks Barricade SMC7004ABR Manuel utilisateur

SMC Networks

SMC Networks BR21VPN - annexe 1 Manuel utilisateur

SMC Networks

SMC Networks ADSL2 Barricade SMC7904BRA3 Instructions d'utilisation et de sécurité

SMC Networks

SMC Networks EZ Connect SMC7003ADSL Manuel utilisateur

SMC Networks

SMC Networks EZ Connect SMC2870W Manuel utilisateur

SMC Networks

SMC Networks Barricade Plus SMC7004FW Manuel utilisateur

SMC Networks

SMC Networks 7004VBR Manuel utilisateur

SMC Networks

SMC Networks SMC7901BRA5 Manuel utilisateur

SMC Networks

SMC Networks SMCWBR14-3GN Manuel utilisateur

SMC Networks

SMC Networks EZ Switch SMC-EZ1024DT Manuel utilisateur

SMC Networks

SMC Networks Barricade SMC7004VBR Manuel utilisateur

SMC Networks

SMC Networks 7004FW - annexe 2 Manuel utilisateur

SMC Networks

SMC Networks SMCWEBT-G Manuel utilisateur

SMC Networks

SMC Networks FS1601 Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité