SMC Networks GS1601 Manuel utilisateur

EZ Connect N

Draft 11n Wireless USB2.0 Adapter

EZ Switch™

16/24-Port Gigabit Ethernet Switch

SMCGS1601/SMCGS2401

SMCGS1601 /SMCGS2401

USER MANUAL

V1.0



Specifications are subject to change without notice

is a registered

trademark of SMC TECHNOLOGIES CO, LTD. Other brands and product names are

trademarks or registered trademarks of their respective holders.

No part of the specifications may be reproduced in any form or by any means or

used to make any derivative such as translation, transformation, or adaptation

http://www.smc.com

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference

in which case the user will be required to correct the interference at his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may

cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

CE Mark Warning

This is a class A product. In a domestic environment, this product may cause radio

interference, in which case the user may be required to take adequate measures.

III

CONTENTS

Package Contents..................................................................................................................... 1

Chapter 1 Product Introduction ............................................................................................. 2

1.1 Product Overview............................................................................................... 2

1.2 Features ................................................................................................................ 2

Chapter 2 Identifying External Components....................................................................... 3

2.1 Front Panel............................................................................................................. 3

2.2 Rear Panel ............................................................................................................. 3

Chapter 3 Installation .............................................................................................................. 4

3.1 Precautions ............................................................................................................ 4

3.2 Installation .............................................................................................................. 4

3.2.1 Desktop Installation ...................................................................................... 5

3.2.2 Rack Installation............................................................................................ 5

3.3 Connect to Ground ............................................................................................... 6

3.4 Power on ................................................................................................................ 8

Appendix A: Specifications ................................................................................................... 9

Appendix B: Troubleshooting..............................................................................................11

Appendix C: Contact Information .......................................................................................11

Package Contents

The following contents should be found in your package:

¾One SMCGS1601 /SMCGS2401 Switch

¾Two power cords (For EU+UK Use)

¾This User Guide

¾Mounting screws and two “L” planks

¾Quick Installation Guide

¾SMC Warranty Card

¾Four rubber foot pads

Note:

Make sure that the package contains the above items. If any of the listed items are

damaged or missing, please contact with your distributor.

Chapter 1 Product Introduction

This chapter describes the features of the SMCGS1601/SMCGS2401 Switch.

1.1 Product Overview

The SMCGS1601/SMCGS2401 Switch provides you with a high-performance,

low-cost, easy-to-use, seamless and standard upgrade to boost your old network to

1000Mbps. Increase the speed of your network server and backbone connections

make Gigabit a reality. Power users in the home, ofﬁce, workgroup, or creative

production environment can now move large, bandwidth-intensive ﬁles faster.

Transfer graphics, CGI, CAD, or multimedia ﬁles and other applications that have

to move large ﬁles across the network almost instantly.

The SMC SMCGS1601/SMCGS2401 Switch features a non-blocking switching

architecture that forwards and filters packets at full wire-speed for maximum

throughput, MAC address auto-learning and auto-aging, IEEE802.3x ﬂow control

for full-duplex mode and backpressure for half-duplex mode. It is compatible with

all 10,100 and 1000Mbps Ethernet devices because it is standard-based. It

protects your existing network investments while providing you with a

straightforward migration path to faster Gigabit speeds.

The SMCGS1601/SMCGS2401 Switch is plug-and-play and no configuration is

required. Auto MDI/MDI-X cable detection on all ports eliminate the need for

crossover cable or Uplink port. Each port can be used as general ports or Uplink

ports, and any port can be simply plugged into a server, a hub, a router or a switch,

using the straight cable or crossover cable. Diagnostic LEDs which display link

status and activity, allowing you to quickly detect and correct problems on the

network.

1.2 Features

¾Complies with IEEE802.3, IEEE802.3u, IEEE802.3ab standards

¾16/24 10/100/1000Mbps Auto-Sense RJ45 ports supporting Auto-MDI/MDIX

¾All ports Support Full/Half Duplex transfer mode for 10/100Mbps and Full

Duplex transfer mode for 1000Mbps

¾Supports IEEE802.3x ﬂow control for full-duplex mode and backpressure for

half-duplex transfer mode

¾Non-blocking switching architecture that forwards and filters packets at full

wire-speed for maximum throughput

¾Supports MAC address auto-learning and auto-aging

¾LED indicators for monitoring power, link, speed and activity

¾Desktop and rack-mountable steel case

¾Internal power supply

Chapter 2 Identifying External Components

This Chapter describes the front panel, rear panel and LED indicators of the Switch.

SMCGS1601 and SMCGS2401 just differ in the number of LED indicators and

ports and all ﬁgures in this guide are of SMCGS2401.

2.1 Front Panel

The front panel of SMCGS2401 consists of switch model, switch LED indicators,

and 24 10/100/1000Mbps RJ-45 ports.

Figure 2-1 SMCGS2401 Switch Front Panel sketch

The LED indicators include Power, Link/Act LED indicators, which are used for

monitoring and pre-troubleshooting of the Switch. The following section shows the

LED indicators of the Switch along with an explanation of each indicator.

¾POWER LED: This indicator will light solid green when the Switch powers up.

If the LED is not lit, please check the power supply and connection.

¾Link/Act LED: The LED indicates Link/Active status. The corresponding LED

indicator will light solid green when connected to a network device. It flashes

green when data is being transmitted or received on the working connection.

¾1000Mbps LED: The corresponding port LED indicator will light solid green

when it's working on 1000Mbps speed. Not lit indicates working on

10/100Mbps speed.

2.2 Rear Panel

The rear panel of SMCGS2401 features a power socket and a Grounding Terminal

(marked with ).

Figure 2-2 SMCGS2401 Switch Rear Panel sketch

¾Grounding Terminal: SMCGS2401 already comes with Lightning Protection

Mechanism. You can also ground the Switch through the PE (Protecting Earth)

cable of AC cord or with Ground Cable. For detail information, please refer to

section 3.3 Connect to Ground.

¾AC Power Socket: Connect the female connector of the power cord here, and

the male connector to the AC power outlet. Please make sure the voltage of the

power supply meets the requirement of the input voltage.

Chapter 3 Installation

3.1 Precautions

To ensure a long-term and stable performance of the Switch, please pay attention

to the following before the installation.

1) Safety Requirements

•Before cleaning the Switch, cut off the power supply. Do not clean it by the

waterish cloth, and never use any other liquid cleaning method.

•Take waterproof measures during storage, transportation and operation of

the equipment.

•Use only the power cord provided with the Switch.

•Make sure the voltage of the power supply meets the requirement of the

input voltage of the Switch.

•Do not push any objects into the openings of the Switch.

•Ensure the vent hole is well ventilated and unblocked.

•Do not open or remove the cover of the Switch.

2) Location Requirements

When you choose a location for the Switch, please follow these guidelines:

•Install the Switch on a flat and stable surface that can support the entire

weight of the Switch with all fittings.

•Locate the Switch far from strong electromagnetic field generators (such as

motors), vibration, dust, and direct exposure to sunlight.

•To ensure adequate air flow around the Switch. At least 10 cm (4 inches) of

space at the front and rear of the Switch is needed for ventilation.

•Make sure that the Switch will be accessible and that the cables can be

easily connected.

•Position the Switch away from water and moisture sources, be sure to

provide an acceptable temperature and humidity operating environment.

3.2 Installation

This Switch can be either installed on the standard 19-inch mountable rack or

located on the desktop.

Caution:

Please unplug the power cord before installing or removing the Switch.

3.2.1 Desktop Installation

To install the Switch on the desktop, please follow the steps:

1) Set the Switch on a flat surface strong enough to support the entire weight of

the Switch with all fittings.

2) Remove the adhesive backing papers from the rubber feet.

3) Turnover the Switch and attach the supplied rubber feet to the recessed areas

on the bottom at each corner of the Switch.

Figure 3-1 Attaching Rubber Feet

4) Upturn the Switch and connect it to the network devices while keep enough

ventilation space around.

5) Connect the Switch to power source with the provided power cord.

Caution:

Please avoid any heavy thing placed on the Switch.

3.2.2 Rack Installation

To install the Switch in an EIA standard-sized, 19-inch rack, follow the instructions

described below:

Autres manuels pour GS1601

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels SMC Networks Routeur réseau

SMC Networks

SMC Networks Barricade Manuel utilisateur

SMC Networks

SMC Networks SMC Barricade Plus SMC7004WFW Manuel utilisateur

SMC Networks

SMC Networks 7901BRA2 - annexe 2 Manuel utilisateur

SMC Networks

SMC Networks Barricade SMC7401BRA Manuel utilisateur

SMC Networks

SMC Networks Edge-corE NETWORKS BARRICADE SMCWGBR14-N2 Manuel utilisateur

SMC Networks

SMC Networks GS1601 Manuel utilisateur

SMC Networks

SMC Networks Barricade SMC2804WBR38 Manuel utilisateur

SMC Networks

SMC Networks 7904BRA3 - annexe 1 Manuel utilisateur

SMC Networks

SMC Networks EZ1026DT Manuel utilisateur

SMC Networks

SMC Networks BARRICADE SMC7301TA Manuel utilisateur

SMC Networks

SMC Networks SMCFS501 Manuel utilisateur

SMC Networks

SMC Networks SMCFS2601 Manuel utilisateur

SMC Networks

SMC Networks SMC6752AL2 Manuel de programmation

SMC Networks

SMC Networks SMC108DT Manuel utilisateur

SMC Networks

SMC Networks SMCWBR14-3GN Manuel utilisateur

SMC Networks

SMC Networks EZ Switch SMCGS1610 Manuel utilisateur

SMC Networks

SMC Networks TigerSwitch SMC6709FL2 Manuel de programmation

SMC Networks

SMC Networks Barricade SMC7004ABR Manuel utilisateur

SMC Networks

SMC Networks Barricade SMC7004VBR Manuel utilisateur

SMC Networks

SMC Networks Barricade SMC7204BRA Manuel utilisateur

SMC Networks

SMC Networks SMC7901BRA5 Manuel utilisateur

SMC Networks

SMC Networks SMC8606T Manuel de programmation

SMC Networks

SMC Networks TIGERSWITCH 10/100 Manuel de programmation

SMC Networks

SMC Networks Barricade Plus SMC7004FW Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité