Siemens TALON Manuel utilisateur

Installation Instructions

Document No. 540-149

September 2, 2008

TALON™ Digital Room Temperature

Sensors

Page 1 of 4

Product Description

These sensors allow users to view and adjust points

in the controller using the sensor buttons and digital

display.

These sensors work with Siemens controllers, and

use a 10K Ωthermistor to detect temperature. The

effective sensing and set point range is 55 to 95°F

(13 to 35°C).

The 587-612B includes an integral fan speed switch

that allows users to override the ventilation fan.

These sensors can be mounted on electrical boxes,

stud-type mounting brackets, or drywall. Obtain the

necessary mounting hardware and follow the

appropriate mounting procedures for the type of

installation required.

Product Numbers

587-610B BACnet Digital Room Temperature

Sensor - white

587-612B BACnet Digital Room Temperature

Sensor with fan switch - white

Warning/Caution Notations

CAUTION Equipment damage, or loss of

data may occur if you do not

follow a procedure as

specified.

Required Tools

•Phillips sizes 1 and 2 screwdrivers

•Medium, flat-blade screwdriver

•Small, flat-blade screwdriver

•Medium-duty electric drill

•3/16-inch (4.8 mm) drill bit

•1-inch (25 mm) hole saw

•Small level

•Tape measure

•Marker or pencil

Item Number 540-149, Rev BA

If using non-terminated or damaged cables, you also

need:

•Room sensor connector tool (RJ-11

crimping tool)

•Room sensor connector kit

Expected Installation Time

20 minutes

Prerequisites

•Review these instructions before beginning.

•Installed: appropriate field wiring (standard

six-conductor room sensor cables, plenum),

within the maximum wiring run length for the

individual equipment controller. The

maximum recommended length is 100 feet

(30 m).

•All wiring must comply with National Electric

Code (NEC) and local regulations.

Figure 1. Room Temperature Sensor with Fan Speed.

Installation Instructions

Document No. 540-149

September 2, 2008

Mounting Information

Always mount the sensor vertically.

Locate the sensor:

•According to design specifications and local

regulations.

•Where the air circulates around it freely (not

in recessed areas or behind doors).

•Allowing a minimum of four inches (10 cm)

free space above and below for proper

airflow, the front cover removal tool, and the

computer communication cable.

•Away from drafts caused by doors, windows,

outside walls, air registers, pipes, return air

plenums, etc.

•Away from heat sources such as strong

lights, fireplaces, direct sunlight, etc.

•On an inside wall (preferably), about five

feet (1.5 m) above the finished floor.

While not recommended, if you need to mount the

sensor on exterior brick or cement-type walls, see

Accessories.

Drywall Mounting (No Rough-in), Typical

1. Mark the center (cable) hole and the mounting

hole locations, using the sensor base plate as a

template. See Figure 2.

CAUTION:

For drywall mounting, only use the top

and bottom holes.

TH0703R1

3/16 (4.8)

1 (25.4)

1-3/8

(34.9)

(25.4)

2-3/8

(60.3)

Figure 2. Mounting and Center Hole Locations

Dimensions in Inches (Millimeters).

2. Drill two 3/16-inch (4.8 mm) mounting holes.

3. Cut a one-inch (25 mm) center hole with a hole

saw.

4. If using screws to attach the sensor, insert two

plastic wall anchors.

5. Pull about three inches (75 mm) of the cable(s)

and/or fan switch wires through the mounting

hardware in the order shown.

Figure 3. Drywall Mounting (No Rough-in), Typical.

6. Mount the sensor base plate on the wall, noting

the UP arrow on the stabilizer plate:

a. Install either the two mounting screws

provided, the drive rivets provided, or

spring clips, but do not tighten.

CAUTION:

Pounding too hard or over-tightening may

cause the sensor base plate to crack or

bend.

b. Level the sensor base plate for

appearance.

c. Tighten the two mounting screws to the

sensor base plate.

7. Do one of the following:

•If the cable is terminated: Inspect the RJ-11

connector for damage.

Page 2 of 4 Siemens Building Technologies, Inc.

Installation Instructions

Document No. 540-149

September 2, 2008

•If the cable is non-terminated or if the RJ-11

was damaged: Cut the cable, leaving about

three inches (75 mm) on the sensor side of

the drywall, and attach an RJ-11 connector

with an RJ-11 crimping tool. On the RJ-11

connectors, ensure that pin Number 1

connects to the same wire at each end of

the cable. See Figure 4. Use the wire nuts

supplied to connect the fan switch wires or

cables.

CAUTION:

For retrofits: Before cutting the cable,

make sure it is disconnected from the

Room Temperature Sensor (RTS) port on

the controller cable end.

Figure 4. Terminating the RJ-11 Connector.

8. Plug the terminated cable into the RJ-11

connector on the back of the sensor's printed

circuit board (PCB).

9. Connect the fan switch to the appropriate

controller leads using the wire nuts supplied.

Feed the extra cables and/or back through the

hole in the rubber insulator.

10. Snap the sensor front to the sensor base plate

by first hooking the sensor front to the bottom

latches, and then pushing the top of the sensor

front into place until it latches.

11. Tighten the sensor front retaining screw. See

Figure 3.

12. Connect the sensor to the Room Temperature

Sensor (RTS) port on the controller. Connect the

fan switch cables (wires) to the appropriate

controller terminal.

The installation is now complete.

Electrical Box and Rough-in Mounting,

Typical

1. If a locator is attached to the rough-in device,

remove the locator by removing the two screws

and lightly rocking the locator to pull it free.

2. Untie the twist tie and pull about three inches

(75 mm) of the sensor cable(s) into the space.

3. If you have a single-sensor electrical box, install

the electrical box adapter plate. See Figure 5.

4. If you have a double-sensor electrical box, install

the required mounting plate(s).

5. If you use a universal adapter kit for a retrofit

job, install the multi-slotted plate in place of the

electrical box adapter plate. See Figure 5.

6. Pull the cable(s) through the required mounting

hardware in the order shown.

7. Install the two sensor mounting screws provided

but do not tighten.

8. Mount the sensor base plate on the wall, noting

the "UP" arrow on the stabilizer plate:

a. Level the sensor base plate for appearance

only.

b. Tighten the two mounting screws to the

sensor base plate.

CAUTION:

Over-tightening may cause the sensor

base plate to crack or bend.

7. Continue with Drywall Mounting (No Rough-in),

Typical, Steps 7 through 13.

The installation is now complete.

Figure 5. Electrical Box and Rough-in Mounting,

Typical.

Siemens Building Technologies, Inc. Page 3 of 4

Installation Instructions

Document No. 540-149

September 2, 2008

Information in this publication is based on current specifications. The company reserves the right to make changes in specifications and models as

design improvements are introduced. TALON is a registered trademark of Siemens Building Technologies, Inc. Other product or company names

Siemens Building Technologies, Inc.

1000 Deerfield Parkway

Buffalo Grove, IL 60089-4513

U.S.A.

Your feedback is important to us. If you have

comments about this document, please send them to

SBT_technical.editor.[email protected]

Document No. 540-149

Country of Origin: U.S.

Page 4 of 4

Accessories

Review Table 1 to verify that you have the appropriate mounting hardware.

For retrofit installations, normally follow the method used by the pre-existing device. You may need to replace existing

mounting hardware. Always mount the sensor vertically.

Table 1. Mounting Accessories.

P/N Description Used For Reference

182-621E Gym Guard Kit, satin

chrome gyms and similar environments requiring a guard.

(Incompatible with adapter bases and the extender

ring.)

155-222P25

(TB 193)

182-683 Metal (and Wood) Stud

Mounting Bracket (pkg. 5) Single-sensor rough-in installations. Kit includes

locator. 129-057

182-685 Spring Clips: Finished

Drywall Mounting Kit

(10 pack)

Drywall mounting. 129-073

192-506 Electrical Box Adapter Plate

Assembly Kit (pkg. 5) Electrical boxes mounted flush with the wall and for

gyms and similar environments requiring a guard.

(Also see 544-782.)

Figure 5

192-860 Finish Plate Kit 1 Gang 1

Sensor; stainless steel Single-sensor, low-cost mounting. Plate is 3.7 × 5.1

inches (9.5 × 12.9 cm) 155-252P25

(TB 238)

536-666 Mounting Strap Standard light switch plate (field-supplied) to mount

sensor on 2 × 4 electrical box 540-040

540-237

544-782B Single Adapter Base

Mounting Kit, white 2 × 4 boxes, all single sensor installations on walls

with oversized holes, paint lines, etc., that need to be

covered, and on exterior brick/cement-type walls. Kit

includes Electrical Box Adapter Plate Assembly

(192-495. Adapter base is 3-1/2 × 5 inches

(8.8 × 12.7 cm).

Figure 5

544-783B Double Adapter Base

Mounting Kit, white 4 × 6 boxes and all double sensor installations on

walls with oversized holes, paint lines, etc., that need

to be covered, and on exterior brick/cement-type

walls. Kit includes two mounting plates (192-720).

Adapter base is 5 × 7 inches (12.7 × 18 cm).

Figure 5

544-784 Non-conduit Rough-in Kit,

Double Double-sensor non-conduit rough-in installations. Kit

includes locator. 540-784

544-785B Extender Ring Kit, white Exterior brick or cement-type walls; fits to back of

sensor base plate —

544-800 Universal Adapter Kit Retrofitting a previous horizontal installation to a

vertical one, or when the screw spacing does not fit

the electrical box adapter plate. Kit includes multi-

slotted adapter plate.

Figure 5

981-344 Electrical Box Cover Plate

Kit 2 × 4 box rough-ins. Kit includes locator and

connector. —

Table des matières

Autres manuels Siemens Régulateurs de température

Siemens

Siemens QAA70 Manuel utilisateur

Siemens

Siemens RDD310 Manuel utilisateur

Siemens

Siemens RDX Series Manuel utilisateur

Siemens

Siemens QAX32.1 Manuel utilisateur

Siemens

Siemens RDH10RF Manuel utilisateur

Siemens

Siemens Synco 900 Mode d’emploi

Siemens

Siemens RDH10RF/SET Manuel utilisateur

Siemens

Siemens REV24RF Instructions d'installation

Siemens

Siemens REV23 Manuel utilisateur

Siemens

Siemens RLA162 Manuel utilisateur

Siemens

Siemens QAX30.1 Manuel utilisateur

Siemens

Siemens 5TC9774-4 Series Manuel utilisateur

Siemens

Siemens RCU50U Manuel du propriétaire

Siemens

Siemens REV23RF16A Manuel utilisateur

Siemens

Siemens RDU50U Manuel du propriétaire

Siemens

Siemens REV23 Manuel utilisateur

Siemens

Siemens BPS242RF Manuel utilisateur

Siemens

Siemens REA23 Manuel utilisateur

Siemens

Siemens REV34 Manuel utilisateur

Siemens

Siemens RDX42.22U Manuel du propriétaire

Siemens

Siemens SITRANS TS100 Guide de l'administrateur

Siemens

Siemens REV15 series Manuel utilisateur

Siemens

Siemens QAX910 Manuel utilisateur

Siemens

Siemens SITRANS TS100 Guide de l'administrateur

Manuels Régulateurs de température populaires d'autres marques

Swegon

Swegon LUNAd MB Manuel utilisateur

Lucky Reptile

Lucky Reptile Thermo Control II Manuel utilisateur

SENSORMETRIX

SENSORMETRIX Argon 100 Manuel utilisateur

Fuji Electric

Fuji Electric PXE4 Manuel utilisateur

Yuyao gongyi

Yuyao gongyi XMT-808 series Manuel utilisateur

Selec

Selec TC544C Manuel utilisateur

P.W. KEY

P.W. KEY rt-208gt Manuel utilisateur

Future Design

Future Design FDC-9200 Manuel utilisateur

BH Thermal

BH Thermal BriskONE Manuel utilisateur

Omron

Omron E5EX-H Manuel utilisateur

West Control Solutions

West Control Solutions KS 45 Guide de démarrage rapide

MCS

MCS RITC-15B Manuel utilisateur

SMC Networks

SMC Networks Thermo-con INR-244-639 Manuel utilisateur

eltherm

eltherm Ex-TC It Series Manuel utilisateur

Omron

Omron C200H-TV Series Manuel utilisateur

industrie technik

industrie technik CA1 Manuel utilisateur

KRAL

KRAL EET 32 Manuel utilisateur

dixell

dixell XR420C Schéma de câblage