Siemens RDD10.1DHW Manuel utilisateur

Operating Instructions RDD10.1DHW

RDD10.1DHW is a temperature controller that allows you to set the ideal room temperature at the

time you want and with independent control of DHW (Domestic Hot Water). There are 3 operating

modes available. You can either rely on the factory settings or make settings that suit your

personal needs.

Display Operation and settings

Warmer / colder

setting the

temperature setpoints

DHW ON/OFF

Changing the

operating mode

between normal

operation, energy

saving and frost

protection mode

Room temperature or setpoint

Batteries

3033Z05en

1.5V

'AA'

1.5V

'AA'

Normal operation

Energy saving mode

Heating ON

Room temperature

Replace batteries

DHW equipment ON

Frost protection mode

Commissioning

The controller is supplied with factory-set temperatures and operating mode. To commission

it, proceed as follows:

1,5 V

"AA"

1,5 V

"AA"

Remove the black transit tabs from the 2 batteries. Check to see if the battery holder

is in its correct position. The controller switches itself on.

Do you want to change the operating mode?

By pressing , you can change the operating

mode. The sequence is started from normal operation,

energy saving mode and frost protection, or vice versa.

Then, the setpoint of the selected operating mode will

be maintained.

In normal operation, the display shows , in energy

saving mode, the display shows , and in frost

protection mode, the display shows .

Default operating mode is “Normal operation”.

When the unit is first powered up,

the display shows .

Are your rooms too warm or too cold?

To increase or decrease the room temperature

setpoint in increments of 0.5 °C, proceed as follows:

•Press to select the operating mode

corresponding to the set point that you want to

change

•Press

+or once

The setpoint display starts flashing

•Press these buttons again to change the

temperature setpoint in the range 5 ... 35 °C

5 seconds after the last push, the new temperature

setpoint will automatically be saved. The display stops

flashing and shows the room temperature currently

measured.

Note:

The setpoint in energy saving mode can be set to

0 °C. This means OFF or, in other words, the

controller is not active in energy saving mode and

symbol will not appear on the display.

Risk of frost!

If you want to have frost protection, press to

select frost protection mode, the display shows

and default value is 5 °C. If the room temperature falls

below the preset frost protection level, it will

automatically activate the heating output.

CE1B3033en / 18.11.2005 Subject to alteration Building Technologies / HVAC Products

Energy saving tips without sacrificing comfort

•Never allow room temperatures to exceed 21 °C

•Press to change to energy saving or frost protection mode, even if

you are absent for short periods of time only

•Air out the rooms for short periods of time only, but properly, with the

windows wide open

Do you want to switch on DHW heating?

•Press to switch on DHW heating

•When DHW heating is switched ON, the display shows the symbol

•When pressing once again, DHW heating will be switched OFF and the

displays will not show the symbol

Does the symbol appear on the display?

1.5V

'AA'

1.5V

'AA'

When this symbol appears, you need to replace the batteries within the following

2 weeks.

Do you want to change the batteries?

•Get 2 new alkaline batteries type AA, 1.5 V

•Remove the battery holder, then the batteries, insert the new batteries and

replace the battery holder

•Make certain the old batteries are disposed of properly, in compliance with

environmental requirements

Recalibrating the sensor

If the room temperature displayed by the controller does

not match the temperature effectively measured, the

temperature sensor can be recalibrated.

Follow the steps below to recalibrate the sensor:

1. In normal operation, press the “+” and operating mode

changeover buttons simultaneously for more

than 3 seconds, switching the system to calibration

mode.

2. The display format in calibration mode is the same as in

normal or energy saving mode, but with the temperature

digits flashing at 1Hz. You can adjust the temperature to

the desired value with the “+” or “-” button at 0.5 K per

step. The maximum adjustable range is +/- 3 K.

3033Z01

3. If no button is pressed for 5 seconds, the system will

return to the initial operating mode and the temperature

is set to the new value.

Note that the operating mode changeover and DHW

buttons are deactivated in calibration mode.

CE1B3033en / 18.11.2005 Subject to alteration Building Technologies / HVAC Products

Autres manuels Siemens Régulateurs de température

Siemens

Siemens RLE132 Manuel utilisateur

Siemens

Siemens RDD310 Manuel utilisateur

Siemens

Siemens RDUxxx Series Manuel utilisateur

Siemens

Siemens QAA910 Manuel utilisateur

Siemens

Siemens RLA162 Manuel utilisateur

Siemens

Siemens QAA24 Manuel utilisateur

Siemens

Siemens AVS13.399 Manuel utilisateur

Siemens

Siemens SITRANS T Series Guide de l'administrateur

Siemens

Siemens TALON Manuel utilisateur

Siemens

Siemens RCC10U Manuel du propriétaire

Siemens

Siemens SITRANS TS100 Guide de l'administrateur

Siemens

Siemens REV24 Manuel utilisateur

Siemens

Siemens SITRANS TS100 Guide de l'administrateur

Siemens

Siemens 24RFDC/SET Manuel utilisateur

Siemens

Siemens QAX32.1 Manuel utilisateur

Siemens

Siemens Polygyr-Compact Manuel du propriétaire

Siemens

Siemens SIMATIC Manuel utilisateur

Siemens

Siemens Landis & Staefa RAV12 Series Manuel utilisateur

Siemens

Siemens RLM162 Manuel utilisateur

Siemens

Siemens RDD10 Series Manuel utilisateur

Siemens

Siemens RDF30U Manuel du propriétaire

Siemens

Siemens SITRANS TS100 Guide de l'administrateur

Siemens

Siemens REV23 Manuel utilisateur

Siemens

Siemens RDH10RF Manuel utilisateur

Manuels Régulateurs de température populaires d'autres marques

Swegon

Swegon LUNAd MB Manuel utilisateur

Lucky Reptile

Lucky Reptile Thermo Control II Manuel utilisateur

SENSORMETRIX

SENSORMETRIX Argon 100 Manuel utilisateur

Fuji Electric

Fuji Electric PXE4 Manuel utilisateur

Yuyao gongyi

Yuyao gongyi XMT-808 series Manuel utilisateur

Selec

Selec TC544C Manuel utilisateur

P.W. KEY

P.W. KEY rt-208gt Manuel utilisateur

Future Design

Future Design FDC-9200 Manuel utilisateur

BH Thermal

BH Thermal BriskONE Manuel utilisateur

Omron

Omron E5EX-H Manuel utilisateur

West Control Solutions

West Control Solutions KS 45 Guide de démarrage rapide

MCS

MCS RITC-15B Manuel utilisateur

SMC Networks

SMC Networks Thermo-con INR-244-639 Manuel utilisateur

eltherm

eltherm Ex-TC It Series Manuel utilisateur

Omron

Omron C200H-TV Series Manuel utilisateur

industrie technik

industrie technik CA1 Manuel utilisateur

KRAL

KRAL EET 32 Manuel utilisateur

dixell

dixell XR420C Schéma de câblage