Siemens RDH10RF/SET Manuel utilisateur

CE1B3070en / 01.03.2010 Subject to alteration Siemens Building Technologies / HVAC Products

Operating instructions RDH10RF/SET

RDH10RF/SET consists of a RDH10RF wireless temperature controller and a RCR10/433 receiver. The RDH10RF

allows you to set the desired room temperature (setpoint) at the time you want. The unit features an ergonomic

setting knob for ease of temperature control.

Display

Actual room temperature in ºC

The unit is controlling to the selected

comfort temperature

Indicates when there is demand for

heat

Replace batteries

TEST

Appears on the screen when the

transmitter is being tested.

Setting knob

Warmer/colder knob for

selecting the temperature

setpoint

Battery compartment

Two alkaline batteries type AA, 1.5 V

Commissioning before start-up

Commissioning

•Remove the black transit tabs from the alkaline batteries.

•Check to see if the battery holder is in the correct position.

•If no batteries are inserted, fit 2 alkaline batteries type AA in the battery compartment.

Initial power-up

Once batteries are fitted, all symbols will appear on

the display as shown for about two seconds.

Selecting the required temperature

•Turn the setting knob counter clockwise to

decrease the setpoint, or clockwise to increase the

setpoint in increments of 0.5 °C

•The required temperature is displayed next to

the comfort temperature symbol

Changing the batteries

1. Get two new batteries of type AA alkaline, 1.5 volts.

2. Remove the battery holder, then the batteries, insert new batteries and

replace the battery holder.

The old, set values must be checked!

3. Make certain the old batteries are disposed of properly, in

compliance with environmental requirements.

Energy saving tips without sacrificing comfort

●Never allow room temperatures to exceed 21˚C.

●Air out rooms: Air out rooms for short periods with open windows and

doors.

CE1B3070en / 01.03.2010 Subject to alteration Siemens Building Technologies / HVAC Products

NOTE:

You can press the OVERRIDE button on the receiver to manually switch ON/OFF for a faulty

room unit or transmission protocol.

NOTE:

You must re-execute the workflow for commissioning the set to reestablish a connection between

the room controller and receiver .

Front View Receiver

LED Signal Indicator LED Relay Indicator

Orange LED indicates relay is on.

The signal is good when the

LED flashes green.

A flashing red LED indicates

that there is no signal. OVERRIDE Button

Press this button to overwrite transmitter

values.

RESET: Press the LEARN & OVERRIDE

button for 4 seconds to delete all transmitter

addresses.

LEARN Button

Rear View Room Unit

(Transmitter)

Press the button to learn a transmitter

address.

Learn Button TEST Button

Release learn telegram Used for testing transmission.

Front View Receiver

Configuration instructions for the Siemens RDH10RF/SET

The Transmitter RDH10RF and the receiver RCR10/433 are set to communicate (bonded) with each

other at the factory. If they fail it is necessary to re bond the units due to loss of communication please

follow the following instructions.

1. Reset receiver by simultaneously pressing the LEARN & OVERRIDE button for 4 seconds.

2. Press and release the LEARN button. This set the receiver to learn mode.

3. Press and release the LEARN button on the back of the transmitter.

4. A green flashing or solid LED indicates a good signal, a red flashing or solid LED indicates no

signal.

5. To test transmission, press the TEST button on the transmitter, switches the relay on in

the receiver regardless of temperature. The RF TEST symbol appears on the thermostat display.

6. An orange LED indicates that the relay is on.

Autres manuels pour RDH10RF/SET

Autres manuels Siemens Régulateurs de température

Siemens

Siemens RDE10.1DHW Manuel utilisateur

Siemens

Siemens RCU50U Manuel du propriétaire

Siemens

Siemens QAA73 Manuel utilisateur

Siemens

Siemens DT-11 Instructions d'installation et d'utilisation

Siemens

Siemens REV34 Manuel utilisateur

Siemens

Siemens BPS242RF Manuel utilisateur

Siemens

Siemens REV23RF16A Manuel utilisateur

Siemens

Siemens QAA70 Manuel utilisateur

Siemens

Siemens REV23 Manuel utilisateur

Siemens

Siemens SITRANS TS100 Guide de l'administrateur

Siemens

Siemens REA23 Manuel utilisateur

Siemens

Siemens RDU50U Manuel du propriétaire

Siemens

Siemens RDJ10RF/SET Manuel utilisateur

Siemens

Siemens RDE10.1DHW Manuel utilisateur

Siemens

Siemens QMX3.P37 Manuel utilisateur

Siemens

Siemens Expert Series Guide de démarrage rapide

Siemens

Siemens QAX30.1 Manuel utilisateur

Siemens

Siemens REV23.03RF Manuel utilisateur

Siemens

Siemens RDH10RF/SET Manuel utilisateur

Siemens

Siemens SITRANS TS100 Guide de l'administrateur

Siemens

Siemens SITRANS Series Guide de l'administrateur

Siemens

Siemens 1000 series Manuel utilisateur

Siemens

Siemens TALON Manuel utilisateur

Siemens

Siemens RVL470 Manuel de l'opérateur

Manuels Régulateurs de température populaires d'autres marques

Swegon

Swegon LUNAd MB Manuel utilisateur

Lucky Reptile

Lucky Reptile Thermo Control II Manuel utilisateur

SENSORMETRIX

SENSORMETRIX Argon 100 Manuel utilisateur

Fuji Electric

Fuji Electric PXE4 Manuel utilisateur

Yuyao gongyi

Yuyao gongyi XMT-808 series Manuel utilisateur

Selec

Selec TC544C Manuel utilisateur

P.W. KEY

P.W. KEY rt-208gt Manuel utilisateur

Future Design

Future Design FDC-9200 Manuel utilisateur

BH Thermal

BH Thermal BriskONE Manuel utilisateur

Omron

Omron E5EX-H Manuel utilisateur

West Control Solutions

West Control Solutions KS 45 Guide de démarrage rapide

MCS

MCS RITC-15B Manuel utilisateur

SMC Networks

SMC Networks Thermo-con INR-244-639 Manuel utilisateur

eltherm

eltherm Ex-TC It Series Manuel utilisateur

Omron

Omron C200H-TV Series Manuel utilisateur

industrie technik

industrie technik CA1 Manuel utilisateur

KRAL

KRAL EET 32 Manuel utilisateur

dixell

dixell XR420C Schéma de câblage