Siemens Simatic S7-1500 Manuel utilisateur
support.industry.siemens.com
5/2022
SIMATIC
S7-1500 / ET 200MP
Communucation module IO-Link Master CM 8xIO-Link
6ES7547-1JF00-0AB0
MANUAL
Edition
S7-1500/ET 200MP
Documentation Guide 1
Product overview 2
Connecting 3
Parameters / address space 4
Diagnostic alarms 5
Technical specifications 6
Dimensional drawing 7
Parameter data record A
SIMATIC
S7-1500/ET 200MP
Communication module IO-Link
Master CM 8xIO-Link
(6ES7547-1JF00-0AB0)
Equipment Manual
08/2022
A5E45488510-AB
Siemens AG
Digital Industries
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E45488510-AB
Ⓟ 07/2022 Subject to change
Copyright © SiemensAG 2019 - 2022.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qual
ified personnel are those who, based on their training and experience, are capable of identifying risks and avoiding
potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical doc
umentation. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and mainten
ance are required to ensure that the products operate safely and without any problems. The permissible ambient
conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of SiemensAG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent edi
tions.
Communication module IO-Link Master CM 8xIO-Link (6ES7547-1JF00-0AB0)
Equipment Manual, 08/2022, A5E45488510-AB
4
Preface
Purpose of the documentation
This manual supplements the ET200MP Distributed I/O System
(https://support.industry.siemens.com/cs/ww/en/view/59191792) system manual. It describes
functions that generally affect the ET200MP distributed I/O system.
The information provided in the present manual, the system manual and the function
manuals enables you to commission the ET200MP distributed I/O system.
Conventions
Please also observe notes marked as follows:
NOTE
A note contains important information on the product described in the documentation, on
the handling of the product or on the section of the documentation to which particular atten
tion should be paid.
Recycling and disposal
For environmentally friendly recycling and disposal of your old equipment, contact a certified
electronic waste disposal company and dispose of the equipment according to the applicable
regulations in your country.
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. Such systems, machines and components should only be connected
to an enterprise network or the internet if and to the extent such a connection is necessary
and only when appropriate security measures (e.g. firewalls and/or network segmentation)
are in place.
For additional information on industrial security measures that may be implemented, please
visit (https://www.siemens.com/industrialsecurity).
Siemens' products and solutions undergo continuous development to make them more
secure. Siemens strongly recommends that product updates are applied as soon as they are
available and that the latest product versions are used. Use of product versions that are no
longer supported, and failure to apply the latest updates may increase customers' exposure to
cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed visit (https://www.siemens.com/industrialsecurity).
Open Source Software
Open-source software is used in the firmware of the I/O modules. Open Source Software is
provided free of charge. We are liable for the product described, including the open-source
software contained in it, pursuant to the conditions applicable to the product. Siemens
accepts no liability for the use of the open source software over and above the intended
program sequence, or for any faults caused by modifications to the software.
For legal reasons, we are obliged to publish the original text of the license conditions and
copyright notices. Please read the information relating to this on the Internet
(https://support.industry.siemens.com/cs/ww/en/view/109757558).
Communication module IO-Link Master CM 8xIO-Link (6ES7547-1JF00-0AB0)
Equipment Manual, 08/2022, A5E45488510-AB 5
Preface
6
1 S7-1500/ET 200MP Documentation Guide.......................................................................................... 7
1.1 S7-1500 / ET 200MP Documentation Guide....................................................................... 7
1.2 SIMATIC Technical Documentation.................................................................................... 8
1.3 Tool support..................................................................................................................... 10
2 Product overview................................................................................................................................ 12
2.1 Properties......................................................................................................................... 12
2.2 Functions......................................................................................................................... 13
2.3 Replacing the IO-Link Master CM 8xIO-Link communication module.................................. 14
2.4 Reset communication module to factory settings............................................................... 14
3 Connecting......................................................................................................................................... 16
3.1 Wiring and block diagram................................................................................................. 16
4 Parameters / address space................................................................................................................ 19
4.1 Parameters....................................................................................................................... 19
4.2 Declaration of parameters................................................................................................. 20
4.3 Address space................................................................................................................... 22
5 Diagnostic alarms............................................................................................................................... 26
5.1 Status and error displays................................................................................................... 26
5.2 Diagnostic alarms............................................................................................................. 28
6 Technical specifications...................................................................................................................... 30
7 Dimensional drawing.......................................................................................................................... 33
7.1 Dimensional drawing........................................................................................................ 33
A Parameter data record........................................................................................................................ 35
A.1 Parameter assignment and structure of parameter data set............................................... 35
Communication module IO-Link Master CM 8xIO-Link (6ES7547-1JF00-0AB0)
Equipment Manual, 08/2022, A5E45488510-AB
Table of contents
S7-1500/ET 200MP Documentation Guide 1
1.1 S7-1500 / ET 200MP Documentation Guide
The documentation for the SIMATIC S7-1500 automation system and the ET200MP
distributed I/O system is arranged into three areas.
This arrangement enables you to access the specific content you require. Changes and
supplements to the manuals are documented in a Product Information.
You can download the documentation free of charge from the Internet
(https://support.industry.siemens.com/cs/ww/en/view/109742691).
Basic information
The System Manual and Getting Started describe in detail the configuration, installation,
wiring and commissioning of the SIMATIC S7-1500 and ET200MP systems.
The STEP7 online help supports you in the configuration and programming.
Examples:
•Getting Started S7-1500
•S7-1500/ET 200MP System Manual
•Online help TIA Portal
Device information
Equipment manuals contain a compact description of the module-specific information, such
as properties, wiring diagrams, characteristics and technical specifications.
Examples:
•Equipment Manuals CPUs
•Equipment Manuals Interface Modules
•Equipment Manuals Digital Modules
•Equipment Manuals Analog Modules
•Equipment Manuals Communications Modules
•Equipment Manuals Technology Modules
•Equipment Manuals Power Supply Modules
7
Communication module IO-Link Master CM 8xIO-Link (6ES7547-1JF00-0AB0)
Equipment Manual, 08/2022, A5E45488510-AB
General information
The function manuals contain detailed descriptions on general topics relating to the SIMATIC
S7-1500 and ET200MPsystems.
Examples:
•Function Manual Diagnostics
•Function Manual Communication
•Function Manual Motion Control
•Function Manual Web Server
•Function Manual Cycle and Response Times
•PROFINET Function Manual
•PROFIBUS Function Manual
Product Information
Changes and supplements to the manuals are documented in a Product Information. The
Product Information takes precedence over the device and system manuals.
You can find the latest Product Information on the S7-1500 and ET200MP systems on the
Internet (https://support.industry.siemens.com/cs/de/en/view/68052815).
Manual Collection S7-1500/ET200MP
The Manual Collection contains the complete documentation on the SIMATIC S7‑1500
automation system and the ET200MP distributed I/O system gathered together in one file.
You can find the Manual Collection on the Internet.
(https://support.industry.siemens.com/cs/ww/en/view/86140384)
SIMATIC S7-1500 comparison list for programming languages
The comparison list contains an overview of which instructions and functions you can use for
which controller families.
You can find the comparison list on the Internet
(https://support.industry.siemens.com/cs/ww/en/view/86630375).
1.2 SIMATIC Technical Documentation
Additional SIMATIC documents will complete your information. You can find these
documents and their use at the following links and QR codes.
The Industry Online Support gives you the option to get information on all topics. Application
examples support you in solving your automation tasks.
8Communication module IO-Link Master CM 8xIO-Link (6ES7547-1JF00-0AB0)
Equipment Manual, 08/2022, A5E45488510-AB
S7-1500/ET 200MP Documentation Guide
1.2 SIMATIC Technical Documentation
Overview of the SIMATIC Technical Documentation
Here you will find an overview of the SIMATIC documentation available in SIOS:
Industry Online Support International
(https://support.industry.siemens.com/cs/ww/en/view/109742705)
Watch this short video to find out where you can find the overview directly in SIOS and how
to use SIOS on your mobile device:
Quick introduction to the technical documentation of automation products per
video (https://support.industry.siemens.com/cs/us/en/view/109780491)
YouTube video: Siemens Automation Products - Technical Documentation at a
Glance (https://youtu.be/TwLSxxRQQsA)
mySupport
With "mySupport" you can get the most out of your Industry Online Support.
Registration You must register once to use the full functionality of "mySupport". After registration,
you can create filters, favorites and tabs in your personal workspace.
Support
requests
Your data is already filled out in support requests, and you can get an overview of
your current requests at any time.
Documentation In the Documentation area you can build your personal library.
Favorites You can use the "Add to mySupport favorites" to flag especially interesting or fre
quently needed content. Under "Favorites", you will find a list of your flagged entries.
Recently viewed
articles
The most recently viewed pages in mySupport are available under "Recently viewed
articles".
CAx data The CAx data area gives you access to the latest product data for your CAx or CAe sys
tem. You configure your own download package with a few clicks:
• Product images, 2D dimension drawings, 3D models, internal circuit diagrams,
EPLAN macro files
• Manuals, characteristics, operating manuals, certificates
• Product master data
You can find "mySupport" on the Internet. (https://support.industry.siemens.com/My/ww/en)
Application examples
The application examples support you with various tools and examples for solving your
automation tasks. Solutions are shown in interplay with multiple components in the system -
separated from the focus on individual products.
You can find the application examples on the Internet.
(https://support.industry.siemens.com/cs/ww/en/ps/ae)
9
S7-1500/ET 200MP Documentation Guide
1.2 SIMATIC Technical Documentation
Communication module IO-Link Master CM 8xIO-Link (6ES7547-1JF00-0AB0)
Equipment Manual, 08/2022, A5E45488510-AB
1.3 Tool support
The tools described below support you in all steps: from planning, over commissioning, all
the way to analysis of your system.
TIA Selection Tool
The TIA Selection Tool tool supports you in the selection, configuration, and ordering of
devices for Totally Integrated Automation (TIA).
As successor of the SIMATIC Selection Tools , it assembles the configuration editors for
automation technology already familiar into a single tool.
With the TIA Selection Tool , you can generate a complete order list from your product
selection or product configuration.
You can find the TIA Selection Tool on the Internet.
(https://support.industry.siemens.com/cs/ww/en/view/109767888)
SIMATIC Automation Tool
You can use the SIMATIC Automation Tool to perform commissioning and maintenance
activities on various SIMATIC S7 stations as bulk operations independent of TIA Portal.
The SIMATIC Automation Tool offers a wide range of functions:
•Scanning of a PROFINET/Ethernet system network and identification of all connected CPUs
•Assignment of addresses (IP, subnet, Gateway) and device name (PROFINET device) to a
CPU
•Transfer of the date and the programming device/PC time converted to UTC time to the
module
•Program download to CPU
•RUN/STOP mode switchover
•CPU localization through LED flashing
•Reading out of CPU error information
•Reading the CPU diagnostic buffer
•Reset to factory settings
•Firmware update of the CPU and connected modules
You can find the SIMATIC Automation Tool on the Internet.
(https://support.industry.siemens.com/cs/ww/en/view/98161300)
PRONETA
SIEMENS PRONETA (PROFINET network analysis) is a commissioning and diagnostic tool for
PROFINET networks. PRONETA Basic has two core functions:
•The "Network analysis" offers a quick overview of the PROFINET topology. It is possible to
make simple parameter changes (for example, to the names and IP addresses of the
devices). In addition, a quick and convenient comparison of the real configuration with a
reference system is also possible.
•The "IO test" is a simple and rapid test of the wiring and the module configuration of a
plant, including documentation of the test results.
You can find SIEMENS PRONETA Basic on the Internet:
(https://support.industry.siemens.com/cs/ww/en/view/67460624)
10 Communication module IO-Link Master CM 8xIO-Link (6ES7547-1JF00-0AB0)
Equipment Manual, 08/2022, A5E45488510-AB
S7-1500/ET 200MP Documentation Guide
1.3 Tool support
Autres manuels pour Simatic S7-1500
77
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Siemens Unité de contrôle
Siemens
Siemens SIMATIC ET 200SP Manuel utilisateur
Siemens
Siemens ZIC-4A Manuel de service
Siemens
Siemens SINUMERIK 840D sl Manuel utilisateur
Siemens
Siemens SINUMERIK 840D sl Manuel utilisateur
Siemens
Siemens Desigo PXC4.E16 Manuel utilisateur
Siemens
Siemens SIMATIC ET 200S Manuel utilisateur
Siemens
Siemens VAG61 Series Manuel utilisateur
Siemens
Siemens SINUMERIK 828D Turning Manuel utilisateur
Siemens
Siemens RDM-MXL Manuel utilisateur
Siemens
Siemens 3UF51 Manuel utilisateur
Siemens
Siemens XC1003-A Mode d’emploi
Siemens
Siemens SED2-LONI/F Manuel utilisateur
Siemens
Siemens LAL Series Manuel utilisateur
Siemens
Siemens SIMOCODE pro Manuel utilisateur
Siemens
Siemens VKF46 Series Manuel utilisateur
Siemens
Siemens SIMOTION D425 Manuel utilisateur
Siemens
Siemens MVS661 N Series Manuel utilisateur
Siemens
Siemens SIPROTEC Manuel utilisateur
Siemens
Siemens ACVATIX VPF53 Series Manuel utilisateur
Siemens
Siemens Simatic S7-1500 Manuel utilisateur
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
