Siemens NIM-1M Manuel utilisateur

P/N 315-099105-6

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Canada Limited

Building Technologies Division

2 Kenview Boulevard

Brampton, Ontario L6T 5E4 Canada

Installation Instructions

Model NIM-1M

Network Interface Modem Module

OPERATION

The Model NIM-1M plug-in modem board from

Siemens Industry, Inc., mounts to and is connected to

the NIM-1W board to provide modem communication

capability for an MXL System XNET network.

The modem transmission line connected to the

NIM-1M can only be Style 4 and can be made using

standard 18 AWG shielded twisted pair or data

grade phone lines.

Note: A pair of NIM-1W / NIM-1M board sets is

referred to as a “bridge” in this document.

INSTALLATION

Remove all system power before installation,

first battery and then AC. To power up, connect AC

first, then the battery.

Setting the Switches

Before mounting the NIM-1M modem module on the

NIM-1W, set all the switches and configuration

jumpers on both modules. Refer to the NIM-1W

Installation Instructions, P/N 315-099165 for infor-

mation on setting the switches on the NIM-1W.

NIM-1M SETTINGS

The NIM-1M has three configuration headers (refer

to Figure 1). The NIM-1Ms are always connected in

board sets, or pairs, with NIM-1Ws to form the

bridge. Designate one board set as NIM-1M LOCAL

and the other as NIM-1M REMOTE. Program the

NIM-1Ms as shown in Table 1.

1ELBAT

sM1-MINEHTGNIMMARGORP

LACOLM1-MINETOMERM1-MIN

1PJ NO 1PJ NO

2PJ NO 2PJ FFO

3PJ FFO 3PJ NO

Mounting

The NIM-1M is mounted on the NIM-1W with 4 nylon

spacers.

1. Snap the 4 nylon spacers into place in the holes

on the underside of the NIM-1M board in the

positions indicated in Figure 2.

2. Position the 4 spacers on the NIM-1M over the 4

holes on the component side of the NIM-1W.

Refer to Figure 3 for representative location of

the NIM-1M on the NIM-1W. Press the spacers

firmly into place in the NIM-1W one at a time.

Cable Connections from NIM-1M to NIM-1W

The NIM-1M has a cable attached to the underside

of the board that connects to JP1 of the NIM-1W.

The cable plug is polarized and connects one way

only. Refer to Figure 3 for the location of JP1. Refer to

the NIM-1W installation instructions, P/N 315-

099106, for installing MXL WAN.

Figure 1

NIM-1M Module Board

NOTES:

1. "ON" IS WHEN THE JUMPER IS IN THE PROPER POSITION

OVER PLUGS JP1, JP2, OR JP3.

2. THE CABLE THAT CONNECTS THE NIM-1M TO THE NIM-1W

IS ATTACHED TO THE UNDERSIDE OF THE NIM-1M.

JP1

NIM-1M

TB1

SHIELD*

RING

TIP

LOCAL EARTH

GROUND

*TIE SHIELD TO EARTH GROUND AT ONE END ONLY

RTSRICDRXDTXDDTRDSRCTSPWR

JP2

JP3

Modem board

ELECTRICAL CONNECTIONS

Note: All connections to the NIM-1W / NIM-1M board

set are power limited to NFPA 70 per NEC

760. All connections are also supervised.

NIM-1M Modem Connections

Modem connection to the NIM-1M can be made

through the standard RJ11 jack (P2) or through TB1

(refer to Figure 2). If TB1 is used, connect TB1-1 TIP

Local to TB1-1 TIP Remote and TB1-2 RING Local

to TB1-2 RING Remote. P1 is for factory use only.

TB1 terminal assignments are as follows:

TB1-1 TIP

TB1-2 RING

TB1-3 LOCAL EARTH GROUND

TB1-3 must be connected to local earth ground. If

shielded cable is used, connect shield to local earth

ground at one side of modem connection only.

Note: When an MXL XNET network using the model

NIM-1W with model NIM-1M board set is

Figure 2

Installing the Spacers on the NIM-1M Module Board

JP2

JP3

JP1

NIM-1M

TB1

INSERT 4 NYLON SPACERS

IN HOLES

IN POSITIONS INDICATED BY ARROWS

ON UNDERSIDE OF

BOARD

NIM-1W

JP4

JP2

JP1

D4 D5

SW1

SW2

87654321

–

ANY

TRBL

ANY

ENABLE XMIT

JP2

JP3

JP1

NIM-1M

TB1

Figure 3

Mounting the NIM-1M Module Board on the NIM-1M Module Board

brought on line, there may be some delay in

network communications while the modems

on the model NIM-1M board establish com-

munications. This may cause a temporary

system trouble which can be cleared once

communications are established.

Refer to the NIM-1W Installation Instructions, P/N

315-099165, to continue with the installation of the

NIM-1W / NIM-1M board set.

ELECTRICAL RATINGS

P/N 315-099105-6

FSK @ 19.2kbps

Transmit level: 10 Dbm

Receive level: 43 Dbm

tnerruCeludoMCDV5evitcAAm0

tnerruCeludoMCDV42evitcAAm07

tnerruCeludoMCDV42ybdnatSAm07

NOTE: SHORT TO EARTH GROUND ON TB1, TERMINALS 1 OR 2 WILLCAUSE GROUND FAULT.

Table des matières

Autres manuels Siemens Unité de contrôle

Siemens

Siemens SIMOTICS CONNECT 400 Manuel utilisateur

Siemens

Siemens 3VL93 Series Manuel utilisateur

Siemens

Siemens SIRIUS 3RA2711 C Series Manuel utilisateur

Siemens

Siemens SINAMICS S120 Manuel de la liste des pièces

Siemens

Siemens SITRANS AW 7MP3112 Series Manuel utilisateur

Siemens

Siemens Simatic S7-1500 CPU 1512C-1 PN Manuel utilisateur

Siemens

Siemens SIMATIC ET 200AL Manuel utilisateur

Siemens

Siemens SIMATIC IM 153-2 Manuel utilisateur

Siemens

Siemens MICROMASTER 420 Manuel utilisateur

Siemens

Siemens SIRIUS 3RA2712 Document technique

Siemens

Siemens CB15 Manuel utilisateur

Siemens

Siemens SIMATIC ET 200SP Manuel utilisateur

Siemens

Siemens SIMOCODE pro Manuel utilisateur

Siemens

Siemens SINAMICS S120 Guide de démarrage rapide

Siemens

Siemens ZIC-4AC Manuel utilisateur

Siemens

Siemens SINUMERIK 840DE SL Guide de démarrage rapide

Siemens

Siemens FCI1802-A2 Manuel utilisateur

Siemens

Siemens IM 328-N Instructions d'utilisation et d'installation

Siemens

Siemens P1 BIM Manuel utilisateur

Siemens

Siemens SITRANS PCS 7 Manuel de la liste des pièces

Siemens

Siemens SIWAREX JB Manuel utilisateur

Siemens

Siemens SITOP DC UPS 6EP1931-2DC21 Manuel utilisateur

Siemens

Siemens SIMOTION D425-2 Manuel utilisateur

Siemens

Siemens 4AI RTD Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur