Siemens CM 1542-5 Manuel utilisateur

___________________

SIMATIC NET

S7-1500 - PROFIBUS

CM 1542-5

Operating Instructions

11/2018

C79000

-G8976-C290-04

Preface

Guide to the documentation

Product overview, functions

Installation, connecting up,

commissioning, operation

Configuration, programming

Diagnostics and upkeep

Technical specifications

Approvals

Siemens AG

Division Process Industries and Drives

Postfach 48 48

90026 NÜRNBERG

GERMANY

C79000-G8976-C290-04

Ⓟ

11/2018 Subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

CM 1542-5

Operating Instructions, 11/2018, C79000-G8976-C290-04 3

Preface

Purpose of the documentation

This device manual supplements the system manual of the automation system S7-1500 and

the function manuals. All functions that go beyond the system are described in the system

manual.

With the information in this manual and the system manual, you will be able to commission

the CM 1542-5 communications module.

Abbreviations and names

●

In this document, the term "CM" (communications module) is used instead of the full

product name "CM 1542-5".

●

STEP 7

The name STEP 7 is used to mean the STEP 7 Professional configuration tool.

New in this edition

●New ATEX/IECEx approval

Replaced edition

Edition 10/2016

Current manual edition on the Internet

You will also find the current version of this manual on the Internet pages of Siemens

Industry Online Support:

Link: (https://support.industry.siemens.com/cs/ww/en/ps/15671/man)

Sources of information and other documentation

See section Guide to the documentation (Page 9).

Preface

CM 1542-5

4Operating Instructions, 11/2018, C79000-G8976-C290-04

License conditions

Note

Open source software

The product contains open

source software. Read the license conditions for open source

software carefully before using the product.

You will find license conditions in the following document on the supplied data medium:

●OSS_CM15425_86.pdf

Firmware

The firmware is signed and encrypted. This ensures that only firmware created by Siemens

can be downloaded to the device.

Security information

Siemens provides products and solutions with industrial security functions that support the

secure operation of plants, systems, machines and networks.

In order to protect plants, systems, machines and networks against cyber threats, it is

necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial

security concept. Siemens’ products and solutions constitute one element of such a concept.

Customers are responsible for preventing unauthorized access to their plants, systems,

machines and networks. Such systems, machines and components should only be

connected to an enterprise network or the internet if and to the extent such a connection is

necessary and only when appropriate security measures (e.g. firewalls and/or network

segmentation) are in place.

For additional information on industrial security measures that may be implemented, please

visit

Link: (http://www.siemens.com/industrialsecurity)

Siemens’ products and solutions undergo continuous development to make them more

secure. Siemens strongly recommends that product updates are applied as soon as they are

available and that the latest product versions are used. Use of product versions that are no

longer supported, and failure to apply the latest updates may increase customers’ exposure

to cyber threats.

To stay informed about product updates, subscribe to the Siemens Industrial Security RSS

Feed under

Link: (http://www.siemens.com/industrialsecurity)

Observe the following security recommendations to prevent unauthorized access to the

system.

●Evaluate your plant as a whole in terms of security. Use a cell protection concept with

suitable products.

●Keep the firmware up to date. Check regularly for security updates of the firmware and

use them.

Preface

CM 1542-5

Operating Instructions, 11/2018, C79000-G8976-C290-04 5

●Restrict physical access to the device to qualified personnel.

●Configure a protection level of the CPU.

Recycling and disposal

The product is low in pollutants, can be recycled and meets the requirements of the WEEE

directive 2012/19/EU "Waste Electrical and Electronic Equipment".

Do not dispose of the product at public disposal sites. For environmentally friendly recycling

and the disposal of your old device contact a certified disposal company for electronic scrap

or your Siemens contact.

Keep to the local regulations.

You will find information on returning the product on the Internet pages of Siemens Industry

Online Support:

Link: (https://support.industry.siemens.com/cs/ww/en/view/109479891)

SIMATIC NET glossary

Explanations of many of the specialist terms used in this documentation can be found in the

SIMATIC NET glossary.

You will find the SIMATIC NET glossary on the Internet at the following address:

Link: (https://support.industry.siemens.com/cs/ww/en/view/50305045)

Preface

CM 1542-5

6Operating Instructions, 11/2018, C79000-G8976-C290-04

CM 1542-5

Operating Instructions, 11/2018, C79000-G8976-C290-04 7

Table of contents

Preface ................................................................................................................................................... 3

1 Guide to the documentation .................................................................................................................... 9

2 Product overview, functions................................................................................................................... 11

2.1 Product data............................................................................................................................11

2.2 Application ..............................................................................................................................12

2.3 Further functions .....................................................................................................................13

2.4 Configuration limits and performance data .............................................................................14

2.4.1 Configuration limits - number of CMs .....................................................................................14

2.4.2 Transmission speeds supported.............................................................................................15

2.4.3 Characteristic data of the DP interface ...................................................................................15

2.4.4 Characteristic data of FDL communication.............................................................................16

2.4.5 Characteristics of S7 communication .....................................................................................17

2.4.6 Performance data / operation .................................................................................................17

2.5 Requirements for use..............................................................................................................18

2.5.1 Project engineering .................................................................................................................18

2.5.2 Programming ..........................................................................................................................18

2.6 LEDs .......................................................................................................................................19

2.7 PROFIBUS interface...............................................................................................................20

3 Installation, connecting up, commissioning, operation ........................................................................... 21

3.1 Important notes on using the device.......................................................................................21

3.1.1 Notes on use in hazardous areas ...........................................................................................21

3.1.2 Notes on use in hazardous areas according to ATEX / IECEx ..............................................22

3.1.3 Notes on use in hazardous areas according to UL HazLoc ...................................................22

3.1.4 Notes on use in hazardous areas according to FM ................................................................23

3.2 Installing and commissioning the CM 1542-5.........................................................................23

3.3 Pin assignment PROFIBUS....................................................................................................24

3.4 Mode of the CPU - effect on the CM.......................................................................................25

4 Configuration, programming .................................................................................................................. 27

4.1 Configuration in STEP 7 .........................................................................................................27

4.2 Program blocks for communication and distributed I/O..........................................................27

4.3 Program blocks for FDL..........................................................................................................28

5 Diagnostics and upkeep ........................................................................................................................ 35

5.1 Diagnostics options.................................................................................................................35

5.2 DP slave diagnostics...............................................................................................................36

5.3 Standard diagnostics ..............................................................................................................37

Table of contents

CM 1542-5

8Operating Instructions, 11/2018, C79000-G8976-C290-04

5.4 Device-specific diagnostics in DP-V1 .................................................................................... 39

5.5 DP diagnostics frames when the CPU is in STOP ................................................................ 42

5.6 Replacing a module without a programming device.............................................................. 42

6 Technical specifications ........................................................................................................................ 43

7 Approvals ............................................................................................................................................. 45

Index .................................................................................................................................................... 51

CM 1542-5

Operating Instructions, 11/2018, C79000-G8976-C290-04 9

Guide to the documentation

Introduction

The documentation of the SIMATIC products has a modular structure and covers topics

relating to your automation system.

The complete documentation for the S7-1500 system consists of a system manual, function

manuals and device manuals.

The STEP 7 information system (online help) also supports you in configuring and

programming your automation system.

Overview of the documentation on communication with S7-1500

The following table lists additional documents, which supplement this description of

CM 1542-5 and are available in the Internet.

Table 1- 1 Documentation for the CM 1542-5

Topic

Documentation

Most important contents

System descrip-

tion

System manual: S7-1500 Automation System

(https://support.industry.siemens.com/cs/ww/e

n/view/59191792)

•Application planning

•Installation

•Connecting

•Commissioning

Module properties Device manual: Power supplies

(https://support.industry.siemens.com/cs/ww/e

n/ps/13721/man)

•Connecting

•Parameter assignment/

addressing

•Interrupts, error messages,

diagnostics and system

alarms

•Technical specifications

•Dimensional drawing

Device manual: Signal modules

(https://support.industry.siemens.com/cs/ww/e

n/ps/13743/man)

System diagnos-

tics

Function manual: System diagnostics

(https://support.industry.siemens.com/cs/ww/e

n/view/59192926)

•Overview

•Diagnostics evaluation for

hardware/software

Communication Function manual: Communication

(https://support.industry.siemens.com/cs/ww/e

n/view/59192925)

•Overview

Function manual PROFINET with STEP 7

(https://support.industry.siemens.com/cs/ww/e

n/view/49948856)

•PROFINET basics

•PROFINET functions

•PROFINET diagnostics

Guide to the documentation

CM 1542-5

10 Operating Instructions, 11/2018, C79000-G8976-C290-04

Topic

Documentation

Most important contents

Function manual PROFIBUS with STEP 7

(https://support.industry.siemens.com/cs/ww/e

n/view/59193579)

•PROFIBUS basics

•PROFIBUS functions

•PROFIBUS diagnostics

Function manual: Web Server

(https://support.industry.siemens.com/cs/ww/e

n/view/59193560)

•Function

•Operation

Interference-free

installation of

control systems

Function Manual: Interference-free installation

of control systems

(https://support.industry.siemens.com/cs/ww/e

n/view/59193566)

•Basics

•Electromagnetic compatibil-

ity

•Lightning protection

•Housing selection

Memory concept Function manual: Structure and Use of the

CPU Memory

(https://support.industry.siemens.com/cs/ww/e

n/view/59193101)

•Design

•Principle of operation

•Use

Cycle and re-

sponse times

Function manual: Cycle and Response Times

(https://support.industry.siemens.com/cs/ww/e

n/view/59193566)

•Basics

•Calculations

Analog value

processing

Function manual: Analog value processing

(https://support.industry.siemens.com/cs/ww/e

n/view/67989094)

•Wiring options

•Tables of measured values

SIMATIC manuals

All current manuals for SIMATIC products are available for download free of charge from the

Internet:

Link: (http://www.siemens.com/automation/service&support)

CP/CM documentation in the SIMATIC NET Manual Collection (article number A5E00069051)

The "SIMATIC NET Manual Collection" DVD contains the device manuals and descriptions

of all SIMATIC NET products current at the time it was created. It is updated at regular

intervals.

Version History / current downloads for the SIMATIC NET S7-CPs/CMs

The "Version History/Current Downloads for SIMATIC NET S7 CPs (PROFIBUS)" provides

information on all CPs available up to now for SIMATIC S7 (PROFIBUS). You will find the

document on the Internet:

Link: (https://support.industry.siemens.com/cs/ww/en/view/67225941)

Autres manuels pour CM 1542-5

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Siemens Unité de contrôle

Siemens

Siemens OLM/P11 V4.0 Manuel utilisateur

Siemens

Siemens SOAM Manuel utilisateur

Siemens

Siemens CUA20 Manuel utilisateur

Siemens

Siemens PN16 Manuel utilisateur

Siemens

Siemens acvatix MVS661 N Series Manuel utilisateur

Siemens

Siemens SINAMICS V90 Guide de l'utilisateur

Siemens

Siemens SINAMICS S120 Manuel de la liste des pièces

Siemens

Siemens FCA2018-U1 Manuel utilisateur

Siemens

Siemens SIMATIC ET 200SP Document technique

Siemens

Siemens SIMATIC ET 200SP Manuel utilisateur

Siemens

Siemens SCALANCE S623 Manuel utilisateur

Siemens

Siemens HOTEL SOLUTION HTC3.2 Series Manuel utilisateur

Siemens

Siemens WFZ661 Manuel d'installation et d'exploitation

Siemens

Siemens SINAMICS G130 Manuel utilisateur

Siemens

Siemens SIRIUS ACT 3SU1803-3NB00-1AE1 Manuel utilisateur

Siemens

Siemens VGD4 series Manuel utilisateur

Siemens

Siemens SIMATIC Manuel utilisateur

Siemens

Siemens SIPROTEC4 7SJ61 Manuel utilisateur

Siemens

Siemens SZE-4X Manuel utilisateur

Siemens

Siemens LVM Manuel utilisateur

Siemens

Siemens FDCIO223 Manuel utilisateur

Siemens

Siemens FDCI223 Manuel utilisateur

Siemens

Siemens simovert masterdrives Manuel utilisateur

Siemens

Siemens Cerberus Pyrotronics NIM-1M Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur