Siemens SIMATIC CP 341 Manuel utilisateur
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.
CAUTION
without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.
NOTICE
indicates that an unintended result or situation can occur if the corresponding information is not taken into
account.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The device/system may only be set up and used in conjunction with this documentation. Commissioning and
operation of a device/system may only be performed by qualified personnel. Within the context of the safety notes
in this documentation qualified persons are defined as persons who are authorized to commission, ground and
label devices, systems and circuits in accordance with established safety practices and standards.
Prescribed Usage
Note the following:
WARNING
This device may only be used for the applications described in the catalog or the technical description and only
in connection with devices or components from other manufacturers which have been approved or
recommended by Siemens. Correct, reliable operation of the product requires proper transport, storage,
positioning and assembly as well as careful operation and maintenance.
Trademarks
All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this
publication may be trademarks whose use by third parties for their own purposes could violate the rights of the
owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Industry Sector
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E02291899-01
Ⓟ 08/2008
Copyright © Siemens AG 2008.
Technical data subject to change
该文档是极速PDF编辑器生成，
如果想去掉该提示,请访问并下载：
http://www.jisupdfeditor.com/
长沙工控帮教育科技有限公司
www.gkbpx.com
CP 341 - First Steps in Commissioning
Getting Started, 09/2008, A5E02291899-01 3
Table of contents
1 First Steps in Commissioning ..................................................................................................................... 5
该文档是极速PDF编辑器生成，
如果想去掉该提示,请访问并下载：
http://www.jisupdfeditor.com/
长沙工控帮教育科技有限公司
www.gkbpx.com
CP 341 - First Steps in Commissioning
Getting Started, 09/2008, A5E02291899-01 5
First Steps in Commissioning 1
Introduction
This guide uses a real-life example to take you through the four steps required to set up a
working application that will enable you to transfer data via the serial interface and to
familiarize yourself with and test the basic functions of your CP 341 as regards both
hardware and software. The references to the manual should give you an initial overview of
the information included within it.
It will take you between 1 and 2 hours to work your way through the example, depending on
your prior experience.
Requirements
The following requirements must be met:
● You have an S7-300 station, consisting of a power supply module and a CPU.
● STEP 7 (≥V5.3) is correctly installed on your programming device.
● You have set up a project for the S7-300 station.
● The programming device is connected to the CPU.
● You have a CP 341 module complete with the associated configuration package and
required connecting cable.
● You have prepared your connection partner for serial data transfer. If you are using a
CP 341 with RS232/V.24 interface, your programming device running the "Hyper
Terminal" program can function as the connection partner. You will find the "Hyper
Terminal" program in Windows under Start > Programs > Accessories > Communication
> Hyper Terminal. The procedure for starting the program is described below.
Installing the Configuration Package on your Programming Device
The configuration package consists of a parameter assignment tool for the CP 341, a library
containing function blocks, and a demo program.
● Start the installation program on the CD by double-clicking the file called SETUP.EXE.
● Follow the instructions issued by the installation program.
该文档是极速PDF编辑器生成，
如果想去掉该提示,请访问并下载：
http://www.jisupdfeditor.com/
长沙工控帮教育科技有限公司
www.gkbpx.com
First Steps in Commissioning
CP 341 - First Steps in Commissioning
6 Getting Started, 09/2008, A5E02291899-01
Installing the CP 341, Connecting to the Communication Partner
● Plug the bus connection supplied with the CP 341 into the CPU's bus port.
● Hook the CP 341 over the rail, lower the bottom edge into position and install the
securing screws.
● Connect the connections L+ and M of your power supply with the respective connections
on the CP.
● Use the connecting cable to interconnect the CP 341 and your connection partner. The
pin assignment of the interface adapter is detailed in the manual.
Test: Apply line voltage to the power supply module. When the initialization phase
completes, the SF LED on the CP 341 is on.
Assigning parameters for the CP 341
● Open your project in SIMATIC Manager.
● In your project, call the "HW Config" configuration table.
● In the hardware catalog, select the CP 341 with the correct order number and drag it to
the appropriate slot.
● Double-click the CP 341 to open the "Properties CP 341" form.
● Note the module address under "Address" (in the demo this address is 256 → 100 Hex).
You will need this value when you set up the link to your user program.
● Click the Parameters button and select the "ASCII" protocol. Double-click the Envelope.
● Click the OK button to accept the parameter assignment defaults:
– 9600 bps,
– 8 data bits,
– 1 stop bit,
– Even parity.
● Select File > Save to save your parameter assignment settings and exit the form with File
> Exit. In the "Properties CP 341" form, click the OK button.
● Save the configuration in your project by selecting Station > Save and Compile.
● Transfer the configuration with the CPU in STOP mode by selecting PLC > Load to
module. The data is transferred directly to the CPU and the CP 341. The SF LED goes
out to indicate that loading was successful.
● Select Station > Exit to close "HW Config".
该文档是极速PDF编辑器生成，
如果想去掉该提示,请访问并下载：
http://www.jisupdfeditor.com/
长沙工控帮教育科技有限公司
www.gkbpx.com
First Steps in Commissioning
CP 341 - First Steps in Commissioning
Getting Started, 09/2008, A5E02291899-01 7
Linking to the user program
The sample project ""zXX21_01_PtP_Com_CP34x" was installed in the
"\Siemens\STEP7\Examples" catalog when you installed the configuration package.
● In the SIMATIC Manager open the example project with File > Open ... > Projects and
double click on the subproject "CP341 Protocol 3964" (also applicable for ASCII
protocols).
● Open the S7 program of the CPU in this project. Double click on the "Blocks" container.
● Apart from the system data, copy all the blocks into your project under SIMATIC 300-
Station > CPU3xx > S7 Program > Blocks.
FC21 FC with SEND
FC22 FC with RECEIVE
DB21, DB22 Instance DBs for the standard FBs
DB40, DB41 Instance DBs for the standard FBs
DB42 DB, from which is being sent
DB43 DB, in which the received data is stored
OB1 cyclic OB
OB100 Restart (warm start) OB
VAT1 Variable table
FB7, FB8 Standard FBs for RECEIVE, SEND
SFC 58, 59 SFCs for the standard FBs
● By double clicking, open the FC22 in your project and in the first line of network 1 change
the the "LADDR" module address from "272" to 256". Save the blocks with File > Save.
● End the editing process of the FCs with File > Exit.
● With SIMATIC Manager, select SIMATIC 300 Station > CPU3xx > S7 Program > Blocks.
With PLC > Download load all the S7 blocks contained here into your CPU (CPU in
STOP state).
● Switch the CPU to RUN.
The CP341 will start to cyclically send data via the serial interface (LED "TxD" flashes). If
you are sending data from your communication partner, this will probably be received by
CP 341 in the DB 43. The destination specifications are entered in the parameters
"DB_NO", "DBB_NO" of the FB7 (P_RCV_RK) in the FC22.
该文档是极速PDF编辑器生成，
如果想去掉该提示,请访问并下载：
http://www.jisupdfeditor.com/
长沙工控帮教育科技有限公司
www.gkbpx.com
First Steps in Commissioning
CP 341 - First Steps in Commissioning
8 Getting Started, 09/2008, A5E02291899-01
Test
Double-clicking VAT1 in the "Blocks" directory in your project allows you to monitor the data
transfer:
● Select PLC > Connect to > Configured CPU to go online.
● Select Variable > Monitor to switch to monitoring mode.
You can view the number of transmissions at the operand "DB42.DBW0" (Send counter).
You can see if you have received data with the "DB41.DBW18" (Receive counter).
If you are using your programming device as a connection partner, you can receive data
from and send data to the CP 341 with the "Hyper Terminal" program. Double-clicking the
"Getting.ht" file (stored in \Siemens\STEP7\s7ftptp\Terminal\...) starts "HyperTerminal" with
the appropriate settings. The data sent by the CP 341 are displayed. The corresponding
characters are sent to the CP 341 by pressing a key on your keyboard.
Diagnostics
Errors can occur in the case of incorrect operation, incorrect wiring of the serial interface or
inconsistent parameter assignment. The manual describes how to diagnose such errors and
messages.
该文档是极速PDF编辑器生成，
如果想去掉该提示,请访问并下载：
http://www.jisupdfeditor.com/
长沙工控帮教育科技有限公司
www.gkbpx.com
Table des matières
Autres manuels Siemens Matériel informatique
Siemens
Siemens Metro 21 M216KASPC Manuel utilisateur
Siemens
Siemens Simatic S7-300 CP 341 Manuel utilisateur
Siemens
Siemens SIMATIC NET CP 443-5 Extended Manuel utilisateur
Siemens
Siemens Simatic S7-300 31xC Series Manuel utilisateur
Siemens
Siemens Simatic M7-400 Manuel utilisateur
Siemens
Siemens SIMATIC S7-1200 Manuel utilisateur
Siemens
Siemens SIMATIC 317TF-2 DP Manuel utilisateur
Siemens
Siemens SIMATIC NET 6GK7 443-5FX02-0XE0 Manuel utilisateur
Siemens
Siemens SIMATIC NET CP 1623 Manuel utilisateur
Siemens
Siemens SIMEAS-Hub 7KE6000-8AD /CC Manuel utilisateur
Siemens
Siemens XMS-SP Manuel utilisateur
Siemens
Siemens SIMATIC S7 400 Guide de l'utilisateur
Siemens
Siemens Simatic VS 710 Manuel utilisateur
Siemens
Siemens SIMATIC NET CP 5613 A2 Manuel utilisateur
Siemens
Siemens SIMATIC CP 541 Manuel utilisateur
Siemens
Siemens Open Processor Manuel utilisateur
Siemens
Siemens SPCN910 Manuel utilisateur
Siemens
Siemens SIMATIC S7-400 CP 440 Manuel utilisateur
Siemens
Siemens EB1 Manuel utilisateur
Siemens
Siemens SIMATIC NET CP 5603 Manuel utilisateur
Manuels Matériel informatique populaires d'autres marques
EMC2
EMC2 VNX Series Manuel du propriétaire
Panasonic
Panasonic DV0PM20105 Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuel utilisateur
Raidon
Raidon iT2300 Manuel utilisateur
National Instruments
National Instruments PXI-8186 Manuel utilisateur
