Seiko ColorPainter V-64S Manuel utilisateur
Troubleshooting GuideTroubleshooting Guide
When you encounter“white lines”, “bleeding”,“stain”and
“dark lines”on the print...
U00118640201
Documents Number U00118640200, First Edition, February 2010
U00118640201, Second Edition, March 2010
Copyright © Seiko I Infotech Inc. 2010
All rights reserved
The content of this document may be changed without a prior notice.
1
How to utilize this Guide
How to utilize this Guide
In the Contents, look for a poor
image quality symptom that is
similar to that of your print.
Go to the designated page, and then
look for a more similar symptom
(pattern). Handle the issue according
to the “Solutions”.
“ P. ” in this Guide show the reference pages in the User’s Guide.
1
Step 2
Troubleshooting
* Some symptoms may have several causes.
Depending on the situation, apply a
combination of the solutions. If the symptom
persists, ink matching with media may not be
good. Change the media and print.
* For more details of each operation in this
Guide, refer to the User's Guide.
Step
2
White lines on the print
Contents
Choose a poor image quality symptom that is similar to that of your print
from below. Refer to the designated page.
Dark lines on the print
Go to page
Stain on the print
Bleeding on the print
3
9
14
19
Go to page
Go to page
Go to page
33
White lines
pattern 1
Go to page
White lineson the print
Main symptoms
[Basic image]
White lines
pattern 2
Go to page
White lines
pattern 3
Go to page
4 5
6
White lines
pattern 4
Go to page 7
White lines
pattern 5
Go to page 8
44
White lines pattern 1
Cause
The media advance is not properly adjusted.
Solution
Solution
Depending on the situation, perform a combination of the solutions below.
Change the pressure force using the Pressure roller up/down lever.
( P.2-34 How to switch the pressure)
Print the image and adjust the media advance value.
( P.4-32 Change during online printing)
HINT
Apply this solution when white lines appear at the same position on each of the six
color stripes printed at the edge of the media. If the white lines appear only on
one of these color stripes, apply the solution for White lines pattern 2.
–
White lines on the print..."White lines pattern 1"
White lines
Pattern 1
White lines
Pattern 2
55
White lines pattern 2
Cause
Clogged nozzles
Solution
Solution
Follow the procedures below.
Check that there is no dust on the platen, if any, remove it.
Perform the daily maintenance and conrm that the symptom is
improved. ( P.4-3 Regular Inspection / Maintenance (Daily maintenance))
Perform the Print head cleaning [NORMAL ALL]. Perform [NOZZLE PRINT]
and conrm that the symptom is improved.
( P.4-19 Print head cleaning, P.4-8 Performing the nozzle print)
Select [RESEAT PRINTHEAD] on the operation panel and move the
carriage. After cleaning the print head nozzle surface, perform [NOZZLE
PRINT] and conrm that the symptom is improved.
( P.5-23 Cleaning of Print head surface, P.4-8 Performing the nozzle print)
HINT
To clean the print head nozzle surface, wipe the print head surface back and
forth lightly, while visually checking, with a Cleaning swab soaked with cap
cleaning liquid.
When print continues with the color stripe [OFF], the above symptom may occur.
Normally, print with the color stripe [ON].
–
–
–
White lines on the print..."White lines pattern 2"
66
White lines pattern 3
Cause
Matching with the media is not good.
The ink dries fast.
Ink does not penetrate into the media.
Solution
Solution
Depending on the situation, perform a combination of the solutions below.
Print in the image improvement [MEDIUM] or [HIGH].
( P.3-34 IMAGE IMPROVEMENT)
Print the media advance adjustment pattern and adjust the media
advance value. ( P.4-28 Media advance value setting procedure)
Raise or lower the heater temperature.
( P.2-41 Changing temperature using the heater control menu)
Set the temperature of the front heater, print heater, and rear heater to be within
the range of ±5ºC of 45ºC, 40ºC and 45ºC, respectively. Be careful not to lose the
temperature balance.
Print in the print mode [QUALITY] ( P.3-25 PRINT MODE)
Set the print mode by the RIP software.
In the RIP software setting, choose the mode to increase paths (“High Quality”, “PASS”,“Quality”,
etc.) and then print.*
Print in the print direction [UNIDIR]. ( P.3-26 PRINT DIRECTION)
Set the print direction by the RIP software.
In the RIP software setting, choose the mode for unidirectional print ("Unidirectional",
"Outward", etc.) and then print.*
Print in the print mode [DENSITY] ( P.3-25 PRINT MODE)
Set the print mode by the RIP software.
In the RIP software setting, choose the mode to increase the ink amount ("Double", etc.) and
then print.*
*To change the settings, contact the RIP software sales agency.
Print using the known good media that has been used in the past.
–
–
–
White lines on the print..."White lines pattern 3"
77
White lines pattern 4
Cause
The media is slantingly advanced.
Solution
Solution
Depending on the situation, perform a combination of the solutions below.
Check that the media on the roll is straight. If is not, replace it.
Check that the media is traveling straight o the roll.
If not, adjust the position of the ange holder or shift the media right or left by raising
the Pressure roller up/down lever to set the media vertically. In addition, when using
the take-up reel unit, adjust the position of flange at the take-up side or re-set the
media.
Conrm that the media is loaded straight against the ange.
If the media is under the entire pressure roller, release the pressure force
of pressure roller. ( P.2-35 How to use the lifter)
HINT
If the media with the ange installed is stood on end, the
media alignment on the roll will become the source of a
possible problem.
–
White lines on the print..."White lines pattern 4"
Sag example
Skew (winding slippage) exampleSkew (winding slippage) example
Sag example
Media
Media
PrinterPrinter
NG OK MediaMedia
NG OK
MediaMedia
Flange Flange
Media
NG
Flange
Flange
88
White lines pattern 5
Cause
The media is coated unevenly.
Solution
Solution
Change to other media.
–
White lines on the print..."White lines pattern 5"
Table des matières
Autres manuels Seiko Imprimante
Seiko
Seiko IP-7900 Manuel utilisateur
Seiko
Seiko IP-4500 MKII Manuel utilisateur
Seiko
Seiko IP-7900 Manuel utilisateur
Seiko
Seiko DPU-414 Manuel utilisateur
Seiko
Seiko TM-T90 Manuel utilisateur
Seiko
Seiko SII RP-E10 Series Manuel utilisateur
Seiko
Seiko DPU-H245AP-A03A-E Manuel utilisateur
Seiko
Seiko MP-B30 Series Manuel utilisateur
Seiko
Seiko MTP Series Manuel d'utilisation et d'entretien
Seiko
Seiko DPU-3445 Manuel utilisateur
Seiko
Seiko LTP1245R-C384-E Manuel d'utilisation et d'entretien
Seiko
Seiko MP-B20 SERIES Manuel utilisateur
Seiko
Seiko SII RP-D10 Series Manuel utilisateur
Seiko
Seiko SII RP-F10 SERIES Manuel utilisateur
Seiko
Seiko IP-7900 Manuel utilisateur
Seiko
Seiko FB 390 Manuel utilisateur
Seiko
Seiko SII SLP721RT Manuel utilisateur
Seiko
Seiko LTPD247A Manuel d'utilisation et d'entretien
Seiko
Seiko RP-E10 Series Manuel utilisateur
Seiko
Seiko PRECISION FB 380 Manuel utilisateur
