Securitytronix ST-PTZIR480-22X Manuel utilisateur
INSTALLATION MANUAL©
ST-PTZIR480-22X
High-Speed Intelligent Dome
IR PTZ Color Camera
Copyright North American Cable Equipment, Inc.
PACKAGE CONTENTS
This package contains:
One ST-PTZIR480-22X high-speed intelligent dome color camera.
One mounting bracket.
One 24VAC 3A power supply.
One installation manual.
PRODUCT DESCRIPTION
The ST-PTZIR480-22X is a professional grade infrared intelligent dome color camera with pan, tilt and zoom (PTZ)
capability and 480TVL resolution. The camera’s non-volatile digital memory allows the saving of all settings. Its
200 preset positions provide versatility for cruise routes and tour functions. The ST-PTZIR480-22X’s mechanical
design permits continuous horizontal 360°rotation and 90°vertical flip. Temperature management is built-in.
Functions and Features
Non-volatile design ensures data will not be lost if power fails.
Recovery function allows the camera to continue previous functions after power is restored.
Support for 200 presets and 4 preset tours, each containing up to 32 presets.
4 patterns, each can be recorded for 1000 discrete PTZ controller moves.
Support for 4-auto scans.
Soft and hard ID settings can be edited on the DIP switch or via the OSD menu.
Integrated multi-protocol control: PELCO“P”, PELCO“D”.
2 ch alarm input; 2 ch alarm relay output.
Proportional zoom lens; P/T speed will decrease in proportion with depth of zoom.
Can be installed indoors or outdoors.
Horizontal pan speed 0.5º-82º/s.
Vertical tilt speed 0.5º-30º/s.
360º continuously horizontal rotation.
Complies with IP 66/CE standard.
Built-in surge protection circuitry.
Auto focus, manual priority.
Auto iris.
Auto shift from Color to B/W.
Built-in OSD makes it easy to configure all settings of the camera.
Built-in display for the internal dome temperature, preset status and compass direction.
330ft IR distance for long-range surveillance.
SPECIFICATIONS
ST-PTZIR480-22X
Specifications (Typical)
1. Image Sensor Samsung SDM-270 with ¼” SONY CCD
2. Resolution 480TVL
3. Lens Auto Iris; F=3.5 to 94.5mm; 22X Optical Zoom, 10X Digital Zoom
4. Illumination 0.1 Lux
5. Pan Range 360º continuous
6. Tilt Rotation Range 0º - 90º flip
7. Manual Speed Pan 0.1º - 82º/sec
8. Manual Speed Tilt 0.1º - 30º/sec
9. Preset Speed 82º/sec
10. Preset Accuracy ±0.10°
11. Preset Positions 200
12. Function Display Yes
14. Pan & Tilt Position Display Yes
15. MAX IR Distance 330ft
19. Patterns 4 programmable (pan/tilt/zoom and each tour is 120 seconds)
20. Sequences (Tours) 4 programmable (dwell time speed preset point)
21. Protocol Pelco-D, Pelco-P selectable
22. Auto Scan With programmable variable speed
23. High Efficient 3-Dimension Scan Yes
24. Long-Focus Speed Limited Yes
26. Home Position Yes
27. Camera Menu Operation Yes
28. IP66 for Outdoor Use Yes
29. Operating Humidity ≤95%
30. Heater Operation 42ºF on; 57ºF off
31. Operating Temperature -40ºF - 122ºF
32. Video Connection BNC coaxial
33. Power 24VAC @3A, 35W
34. Communication RS485
Dimensions
Wall Mount Dimension
Picture 2
6 ½”
7 ¾”
5 ¼” 5 ½”
6”
10 1/8”
4 1/8”
6”
4 1/8”
6 1/8”
3 ¾”
5 ½”
INSTALLATION AND OPERATION
CAUTION: To reduce the risk of electrical shock do not remove the cover or back of this unit. No user
serviceable parts are inside.
CAUTION: To prevent electric shocks and risk of fire hazards, do not use other than specified power
source.
1. UNPACKING and HANDLING
Each unit is shipped partially assembled factory tested.
Ensure that all accessories are removed from the container before discarding packing materials.
a. Use the mounting arm as a template to mark the holes for your mounting hardware.
This symbol is intended to alert the user to the presence of important operating and
maintenance (servicing) instructions.
This symbol is intended to alert the user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a
risk of electrical shock.
b. Feed the cable assembly up through the smaller end of the mount and out the rear opening.
c. Assemble the camera dome to the mounting arm using the 4 supplied allen-head cap screws and allen
wrench.
2. MECHANICAL INSPECTION
Inspect the entire camera for shipping damage. Make sure the equipment is clean, and no connectors are
broken, damaged, or loose. If equipment appears to be damaged or defective please contact your distributor
or SecurityTronix at 1-610-429-1511 for assistance.
3. SPECIAL ATTENTION
a. The installer must comply with electrical safety standards. There must be sufficient space between the
camera’s power supply and video line and any high voltage equipment and/or cables.
b. To help ensure the camera’s life and proper operation do not point the camera towards the sun or
strong light.
c. Do not install the camera in an environment where the temperature is above 122°F.
d. Do not install the camera near a magnetic field or a high-power motor.
e. Do not mount the camera near a radiator or heater.
f. The installation site and material must fully support the weight of the product.
g. Only use a dry cloth to clean the camera. If there is dirt that is difficult to remove wipe gently with a mild
detergent. Never use strong or abrasive detergents.
h. The included 24VAC at 3A power supply must be used. Using a DC or other incorrect power supply
will damage the camera.
i. Only qualified installers are allowed to install, test and disassemble the camera.
j. The camera is a low voltage product. If installed outdoors proper safety and lightning grounding are
required.
k. Before installing be sure the grounding, wiring, input power, voltage, DIP switches, communication
protocol and baud rate are correctly set prior to powering up and using.
4. CAMERA SETUP
BAUD RATE & PROTOCOL SETUP
DIP Switch Settings
Baud rate Setting SW2（B7~B8）
Protocol Setting SW2（B1~B2）
DOME ADDRESS SETUP
System Setup DIP Switch SW1 ON = 1 OFF = 0
V2.0 7-31-12
9
V2.0 7-31-12
10
5. WIRING CONNECTIONS
6. FUNCTIONS and OPERATION
Menu Operation
Several functions can be accessed directly without using the camera’s on screen menu display.
Note the following dedicated preset functions:
Special Use Preset Numbers
Call PRESET 95 ―― Enter into main OSD menu
Call PRESET 96 ―― Run pattern 1
Call PRESET 97 ―― Run Sequence 1
Call PRESET 92 ―― Set Left limit point for L/R scan
Call PRESET 93 ―― Set Right limit point for L/R scan
Call PRESET 99 ―― Run Left-right scan
•NOTE: If Left limit point and Right limit point are set to the same position, calling preset 99
will execute a 360° scan.
Call PRESET 33 ―― Swing 180°
Call PRESET 34 ―― Return to Zero point
The on screen menu provides access to all camera functions through the use of a standard RS485
connection and PTZ controller.
As shown above, use the PTZ controller to CALL PRESET 95 and the camera’s OSD menu will
appear overlaid upon the video output of the camera, as shown below.
Table des matières
Autres manuels Securitytronix Caméra de sécurité
Securitytronix
Securitytronix ST-D600IRVP2812 Manuel utilisateur
Securitytronix
Securitytronix ST-D540IRVP2812 Manuel utilisateur
Securitytronix
Securitytronix ST-HDC2FB Manuel utilisateur
Securitytronix
Securitytronix ST-D4203.6B Manuel utilisateur
Securitytronix
Securitytronix ST-BT6003.6-W2 Manuel utilisateur
Securitytronix
Securitytronix HD-COAXINATORTVI ST-HDC2FTD Manuel utilisateur
Securitytronix
Securitytronix ST-DLI420IR6-B Manuel utilisateur
Securitytronix
Securitytronix ST-D600VP3.6-B-W Manuel utilisateur
Securitytronix
Securitytronix ST-D420IR3.6 Manuel utilisateur
Securitytronix
Securitytronix ST-D540IRVP49-S Manuel utilisateur
Securitytronix
Securitytronix ST-IP4VFD-MZL Manuel utilisateur
Securitytronix
Securitytronix HD-COAXINATORTVI ST-HDC2PTZ Manuel utilisateur
Securitytronix
Securitytronix HD-COAXINATORTVI ST-HDC2FD Manuel utilisateur
Securitytronix
Securitytronix HD-CDAXINATORTVI ST-HDC2VFD-MZ Manuel utilisateur
Securitytronix
Securitytronix ST-DWDIRVF2812-720B Manuel utilisateur
Securitytronix
Securitytronix ST-PTZIR650-23 Manuel utilisateur
Securitytronix
Securitytronix ST-BT1000IR2812-G Manuel utilisateur
Securitytronix
Securitytronix ST-DWD600IRVP49-S Manuel utilisateur
Securitytronix
Securitytronix ST-PTZ480-22 Manuel utilisateur
Securitytronix
Securitytronix ST-IP2VFB Manuel utilisateur
