Securitytronix ST-DWD650IRVP2812-B/W Manuel utilisateur

INSTALLATION MANUAL

ST-DWD650IRVP2812-B/W

Vandal-Proof Infrared Color Camera

V1.0 5/8/131

PACKAGE CONTENTS

This package contains:

One ST-DWD650IRVP2812-B/W Vandal-Proof Dome Infrared Color camera

One installation manual

Note: The ST-DWD650IRVP2812-B/W requires a 12VDC 500mA power supply such as

the ST-PS12VDC1A or ST-PS12VDC2A.

PRODUCT DESCRIPTION

The ST-DWD650IRVP2812-B/W is a vandal-proof infrared camera designed around a 1/3” Color

SONY Super HAD CCD with 650TVL of resolution, 36 infrared LEDs providing infrared capability

up to 90 feet and a 2.8mm –12mm manual zoom lens. The ball style dome camera provides the

installer with the ability to easily adjust the camera’s viewing area. The ST-DWD650IRVP2812-

B/W is a cost effective surveillance solution for any budget.

SPECIFICATIONS

ST-DWD650IRVP2812-B/W

Specifications (Typical)

Image Sensor

1/3” SONY Super HAD CCD

Pixels (HxV)

811x508

Scanning System

NTSC

Horizontal Resolution

650TV Lines

Synchronization

Internal, negative sync

Minimum Illumination

0.001Lux, 0Lux (IR LED on)

Scanning System

2 :1 interface

Auto Electronic Shutter

1/60 ~1/100,000 Seconds

S/N Ratio

>48dB

10. Lens

2.8mm –12mm manual zoom

11.

Auto Gain Control

Auto

12. IR LED

φ5x36PCS

13.

IR Viewing Distance

Up to 90 feet

14.

Gamma Correction

0.45

15.

Video Output

1.0Vp-p/75Ω

16.

Operation Temperature

14- 113F

17.

Relative Humidity

95% maximum

18.

Dimensions

5.2”x3.7”

19.

Weight

1.8 lbs.

20.Power Supply

DC12V 500mA

V1.0 5/8/132

INSTALLATION AND OPERATION

1. UNPACKING and HANDLING

Each unit is shipped assembled and factory tested.

Ensure that all accessories are removed from the container before discarding packing material

2. MECHANICAL INSPECTION

Inspect the front and rear of the equipment for shipping damage. Make sure the equipment is

clean, and no connectors are broken, damaged, or loose. If equipment appears to be

damaged or defective please contact your distributor or Security Tronix at 1-610-429-1511 for

assistance.

3. SPECIAL ATTENTION

a. The installer must comply with electrical safety standards. There must be sufficient

space between the camera’s power supply and video line and any high voltage

equipment and/or cables.

b. To help ensure the camera’s life and proper operation do not point the camera

towards the sun or strong light.

c. Do not install the camera in an environment where the temperature is above 113F.

The camera should be installed in a cool and spacious environment.

d. Do not install the camera near a magnetic field or a high-power motor.

e. Only use a dry cloth to clean the camera. If there is dirt that is difficult to remove wipe

gently with a mild detergent. Never use strong or abrasive detergents.

f. A 12VDC 500mA power supply must be used. AC power cannot be applied. Using a

power supply other than 12VDC 500mA will damage the camera.

g. Only qualified installers are allowed to install, test and disassemble the camera.

h. The IR LED angle and lens viewing range are adjusted at the factory. Any change to

the camera’s lens will affect image quality.

i. The camera is a low voltage product. If installed outdoors proper safety and

lightening grounding are required.

4. WIRING CONNECTIONS

a. Connect the power supply’s DC plug to the camera’s power outlet.

b. Connect the camera to the monitor with a 75Ωcoaxial video cable.

c. Connect power supply’s AC plug to a suitable AC power outlet.

d. Adjust the lens direction according to the required surveillance area and environment.

V1.0 5/8/133

5. OSD SETTINGS

Accessing the camera’s OSD menu and making menu selections is

accomplished using the attached “cursor pad”: UP, DOWN, LEFT, RIGHT

and PUSH center for entering the selection.

V1.0 5/8/134

V1.0 5/8/135

6. TROUBLESHOOTING

a. No picture after applying power –(i) check all plugs and cables are securely

connected to the proper connectors; (ii) ensure your power supply is providing the

correct voltage and current.

b. The picture has ripples –(i) check to see if the power supply is experiencing AC

ripple, if so a filter may be required; (ii) determine if the monitor is faulty; (iii)

determine if other peripheral equipment is causing ripple and if so make the

necessary adjustments.

c. The picture background continuously changes color –a fluorescent lamp’s magnetic

field may cause color roll, therefore, reduce the number of fluorescent lamps or

increase the distance between the camera and the lamps.

d. The picture appears smeared –(i) the power supply voltage level may be unstable,

therefore, try another power supply; (ii) ensure the cables are correctly connected

and/or the cables are of the correct impedance.

e. Other interference may require a Security Tronix ground loop isolation filter.

f. Additional troubleshooting assistance can be found on-line at www.securitytronix.com

in addition to support from Security Tronix sales engineers at 1-610-429-1511.

V1.0 5/8/136

Table des matières

Autres manuels Securitytronix Caméra de sécurité

Securitytronix

Securitytronix ST-IP2VFD Manuel utilisateur

Securitytronix

Securitytronix ST-DWD600IRVP2812-B Manuel utilisateur

Securitytronix

Securitytronix ST-DLI420IR6-B Manuel utilisateur

Securitytronix

Securitytronix ST-D600IR2812-DSHB Manuel utilisateur

Securitytronix

Securitytronix ST-D420IR6-B Manuel utilisateur

Securitytronix

Securitytronix ST-D650IRVP-B Manuel utilisateur

Securitytronix

Securitytronix ST-IP2FWD Manuel utilisateur

Securitytronix

Securitytronix ST-HD-D2812M-2MP Manuel utilisateur

Securitytronix

Securitytronix ST-D600IRVP2812 Manuel utilisateur

Securitytronix

Securitytronix ST-D700IR2812-B/W Manuel utilisateur

Securitytronix

Securitytronix ST-D1000P-W Manuel utilisateur

Securitytronix

Securitytronix ST-PTZIR480-22X Manuel utilisateur

Securitytronix

Securitytronix ST-CVTMD520-WPIR-W Manuel utilisateur

Securitytronix

Securitytronix ST-IP4FWD Manuel utilisateur

Securitytronix

Securitytronix ST-IP2VFB Manuel utilisateur

Securitytronix

Securitytronix ST-CVTMD420-WPIR-W Manuel utilisateur

Securitytronix

Securitytronix ST-HD-BT3.6-1MP Manuel utilisateur

Securitytronix

Securitytronix ST-DLI600VP3.6-B-W Manuel utilisateur

Securitytronix

Securitytronix ST-DWDVF2812-720B/W Manuel utilisateur

Securitytronix

Securitytronix ST-DWDIRVF2812-720B Manuel utilisateur

Securitytronix

Securitytronix ST-IP2FB Manuel utilisateur

Securitytronix

Securitytronix ST-PTZIR530-36 Manuel utilisateur

Securitytronix

Securitytronix ST-IP6FE Manuel utilisateur

Securitytronix

Securitytronix ST-BT6003.6-W2 Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur