Securitytronix ST-D4203.6B Manuel utilisateur

INSTALLATION MANUAL

ST-D4203.6B

ST-D4202.8B

Plastic Dome Color Camera

PACKAGE CONTENTS

This package contains:

One ST-D4203.6B or ST-D4202.8B plastic dome color camera

One installation manual

Note: The ST-D54203.6B / ST-D4202.8B requires a minimum12VDC 150mA power supply such

as the ST-PS12VDC1A or ST-PS12VDC2A.

PRODUCT DESCRIPTION

The ST-D420 series is an indoor plastic dome color camera designed around a 1/3” Color SONY

CCD with 420TVL of resolution. The ST-D4203.6B’s 3.6mm lens and the ST-D4202.8B’s 2.8mm

lens, size and packaging allow these cameras to be easily and discretely installed. Their rich color,

high definition, stability and resistance to jamming make them attractive for CCTV security

applications.

SPECIFICATIONS

ST-D4203.6B / ST-D4202.8B

Specifications (Typical)

1. Image Sensor

1/3” SONY CCD

2. Pixels (HxV)

510x492

3. Scanning System

NTSC

4. Horizontal Resolution

420TV Lines

5. Synchronization

Internal, Negative Synch

6. Minimum Illumination

0.5Lux

7. Scanning System

2 :1 interface

8. Auto Electronic Shutter

1/60~1/100,000 Seconds

9. Lens

3.6mm/F2 Board Lens / 2.8mm/F2 Board Lens

10. S/N Ratio

>48dB

11. Gamma Correction

0.45

12. Video Output

1.0Vp-p/75Ω

13. Operation Temperature

14°- 113°F

14. Power Supply

DC12V 150mA

15. Dimensions

4.6”x2.9”

16. Weight

12.3 ozs

INSTALLATION AND OPERATION

CAUTION: To reduce the risk of electrical shock do not remove the cover or back of this

unit. No user serviceable parts are inside.

CAUTION: To prevent electric shocks and risk of fire hazards, do not use other than

specified power source.

1. UNPACKING and HANDLING

Each unit is shipped assembled and factory tested.

Ensure that all accessories are removed from the container before discarding packing material

2. MECHANICAL INSPECTION

Inspect the front and rear of the equipment for shipping damage. Make sure the equipment is

clean, and no connectors are broken, damaged, or loose. If equipment appears to be

damaged or defective please contact your distributor or SecurityTronix at 1-610-429-1511 for

assistance.

3. SPECIAL ATTENTION

a. The installer must comply with electrical safety standards. There must be sufficient

space between the camera’s power supply and video line and any high voltage

equipment and/or cables.

b. To help ensure the camera’s life and proper operation do not point the camera

towards the sun or strong light.

c. Do not install the camera in an environment where the temperature is above 113°F.

The camera should be installed in a cool and spacious environment.

d. Do not install the camera near a magnetic field or a high-power motor.

e. Do not mount the camera near a radiator or heater.

f. Only use a dry cloth to clean the camera. If there is dirt that is difficult to remove wipe

gently with a mild detergent. Never use strong or abrasive detergents.

g. A minimum 12VDC 150mA power supply must be used. AC power cannot be applied.

Using an AC or other incorrect power supply will damage the camera.

h. Only qualified installers are allowed to install, test and disassemble the camera.

i. The camera is a low voltage product. If installed outdoors proper safety and lightening

grounding are required.

This symbol is intended to alert the user to the presence of important operating and

maintenance (servicing) instructions.

This symbol is intended to alert the user to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a

risk of electrical shock.

4. WIRING CONNECTIONS

a. Connect the power supply’s DC plug to the camera’s power outlet.

b. Connect the camera to the monitor with a 75Ωcoaxial video cable.

c. Connect power supply’s AC plug to a suitable AC power outlet.

d. Adjust the lens direction according to the required surveillance area and environment.

5. TROUBLESHOOTING

a. No picture after applying power –(i) check all plugs and cables are securely

connected to the proper connectors; (ii) ensure your power supply is providing the

correct voltage and current.

b. The picture has ripples –(i) check to see if the power supply is experiencing AC ripple,

if so a filter may be required; (ii) determine if the monitor is faulty; (iii) determine if

other peripheral equipment is causing ripple and if so make the necessary

adjustments.

c. The picture background continuously changes color –a fluorescent lamp’s magnetic

field may cause color roll, therefore, reduce the number of fluorescent lamps or

increase the distance between the camera and the lamps.

d. The picture appears smeared –(i) the power supply voltage level may be unstable,

therefore, try another power supply; (ii) ensure the cables are correctly connected

and/or the cables are of the correct impedance.

e. Other interference may require a SecurityTronix ground loop isolation filter.

f. Additional troubleshooting assistance can be found on-line at www.securitytronix.com

in addition to support from SecurityTronix sales engineers at 1-610-429-1511.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Securitytronix Caméra de sécurité

Securitytronix

Securitytronix ST-DWD650IRVP2812-B/W Manuel utilisateur

Securitytronix

Securitytronix ST-D600IR2812-HB Manuel utilisateur

Securitytronix

Securitytronix ST-DLI420IR6-B Manuel utilisateur

Securitytronix

Securitytronix ST-D650IRVP-B Manuel utilisateur

Securitytronix

Securitytronix ST-BT800P-W Manuel utilisateur

Securitytronix

Securitytronix HD-COAXINATORTVI ST-HDC2VFTD-MZ Manuel utilisateur

Securitytronix

Securitytronix ST-WD600PTZMINI Manuel utilisateur

Securitytronix

Securitytronix ST-PTZ480-22 Manuel utilisateur

Securitytronix

Securitytronix ST-IP4FWD Manuel utilisateur

Securitytronix

Securitytronix ST-D6003.6 –B Manuel utilisateur

Securitytronix

Securitytronix ST-IP-BT3.6-1 Manuel utilisateur

Securitytronix

Securitytronix ST-DWD600IRVP2812-B Manuel utilisateur

Securitytronix

Securitytronix ST-PTZIR480-22X Manuel utilisateur

Securitytronix

Securitytronix ST-IP2VFD Manuel utilisateur

Securitytronix

Securitytronix ST-HD-D2812M-2MP Manuel utilisateur

Securitytronix

Securitytronix ST-IP-MD36-1 Manuel utilisateur

Securitytronix

Securitytronix ST-BT650IRVFDV –B Manuel utilisateur

Securitytronix

Securitytronix ST-HD-BT3.6-1MP Manuel utilisateur

Securitytronix

Securitytronix ST-PTZ650FM-23X Manuel utilisateur

Securitytronix

Securitytronix HD-COAXINATOR ST-HD-PTZ-2MP Manuel utilisateur

Securitytronix

Securitytronix ST-DWDIRVF2812-720B Manuel utilisateur

Securitytronix

Securitytronix ST-DWD650IR-B Manuel utilisateur

Securitytronix

Securitytronix ST-BTLI540IRVFDV Manuel utilisateur

Securitytronix

Securitytronix ST-DWD700-3.6-B Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur