Satel CA-64 ADR-MOD Manuel utilisateur

CA-64 ADR-MOD

ADDRESSABLE MODULE

ca64adr_mod_en 09/15

The CA-64 ADR-MOD module makes it possible to convert the detector of NO or NC type

into the addressable detector. Addressable detectors are supported by the INT-ADR /

CA-64 ADR addressable zone expander. Compact size of the addressable module enables it

to be mounted inside the detector enclosure.

1. Description

Explanations to Fig. 1:

- white wire – common ground,

- black wire – data output,

- blue wire – detector status supervision input,

- red wire – power input (+12 V DC).

The DIP-switches are used for module address setting. A numerical value is assigned to

each switch. In the OFF position, the value is 0. Numerical values assigned to individual

switches in the ON position are shown in Table 1. The sum of numerical values assigned to

switches 1-6 denotes the address set in the module. Addresses from the 0-47 range should

be set. Modules with higher addresses are not supported. A different address must be set in

each module. Setting the same address in two modules will result in two addressable

detectors being assigned to the same zone.

DIP-switch number 1 2 3 4 5 6

Numerical value 1 2 4 8 16 32

Table 1.

For further information on addressing the modules and numbering the addressable zones,

please refer to the manual of INT-ADR / CA-64 ADR expanders.

2. Connecting

The maximum distance between the addressable detector and the expander may be up to

1000 m. The addressable modules and detectors should be powered from the POW output of

the expander. Use separate wires to connect the power common for addressable modules

and the power common for detectors. Connect to one of the detector alarm output terminals

the same common ground which is connected to the addressable module. Connect the other

terminal of alarm output to the module blue wire of the addressable module (detector status

supervision input). Black module wire (data output) connect to INT terminal of the expander.

Connection without tamper control

Program the addressable zone in the control panel as NO or NC (depending on the detector

type). Connect the detector tamper output (TMP) to a separate tamper circuit.

2 CA-64 ADR-MOD SATEL

Connection with tamper control

Program the addressable zone in the control panel as 2EOL/NO or 2EOL/NC (depending on

the detector type). Connect the detector tamper output (TMP) in series to the

CA-64 ADR-MOD module supply circuit.

3. Specifications

Supply voltage ................................................................................................... 12 V DC ±15%

Current consumption.......................................................................................................1.2 mA

Enclosure dimensions ....................................................................................... 37 x 17 x 8 mm

The declaration of conformity may be consulted at www.satel.eu/ce

SATEL sp. z o.o. • ul. Budowlanych 66 • 80-298 Gdańsk • POLAND

tel. + 48 58 320 94 00

www.satel.eu

Table des matières

Autres manuels Satel Unité de contrôle

Satel

Satel STAM-1 TRNK Manuel utilisateur

Satel

Satel GSM-4 Manuel utilisateur

Satel

Satel ETHM-A Manuel utilisateur

Satel

Satel ETHM-1 Manuel utilisateur

Satel

Satel GPRS-A Manuel utilisateur

Satel

Satel GSM LT-2 Manuel utilisateur

Satel

Satel ETHM-1 Plus Manuel utilisateur

Satel

Satel SATELLINE-M3-TR1 Manuel utilisateur

Satel

Satel GPRS-T6 Manuel utilisateur

Satel

Satel INT-VMG Manuel utilisateur

Satel

Satel MZ-1 Manuel utilisateur

Satel

Satel GSM-X Manuel utilisateur

Satel

Satel GSM LT-1S Manuel utilisateur

Satel

Satel ETHM-A Manuel utilisateur

Satel

Satel MST-1 Manuel utilisateur

Satel

Satel PK-01 Manuel utilisateur

Satel

Satel GPRS-T4 Manuel utilisateur

Satel

Satel GSM LT-1 Manuel utilisateur

Satel

Satel ETHM-1 Manuel utilisateur

Satel

Satel GSM-4S Manuel utilisateur

Satel

Satel ETHM-1 Plus Manuel utilisateur

Satel

Satel ETHM-2 Manuel utilisateur

Satel

Satel GSM-X Manuel utilisateur

Satel

Satel SATEL-LP8 Guide de démarrage rapide

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur