Sanuvox Bio-Wall MAX Manuel utilisateur
Troubleshooting guide for the Bio-Wall MAX Screen
Disconnect all power sources before servicing or touching any internal components.
Sanuvox Technologies, Montréal
www.sanuvox.com
April 2017
WARNING
Table&of&content&
Internal parts of the screen .................................................................................. Erreur ! Signet non défini.
Troubleshooting ................................................................................................... Erreur ! Signet non défini.
step by step .......................................................................................................... Erreur ! Signet non défini.
&
&
Internal&parts&of&the&screen&
If necessary, open the cover and identify all the components.
&
Memory
card
Flat cable and connector
Troubleshooting&&
Problems
Possible causes:
Try the following:
Screen is black
• Power to the screen is limited
• No power supplied to the screen
• Verify that power supply is
5VDC/1.5A
• Verify that the power cord is not
damaged or cut.
• Test the outlet to make sure there
is power by using another
electrical appliance.
Screen displays Drive not mounted
• The memory card is missing or
defective.
• Remove the screen cover and
make sure that the memory card is
correctly positioned and
connected.
Screen displays Check the
communication cable or No data
transfer detected
• Ethernet cable is disconnected
• There is no power to the Biowall
• Ethernet cable is too long
• Ethernet cable is damaged
• Wrong type of Ethernet cable is
used
• Too much interference near the
Ethernet cable
• Disconnect power to the screen,
wait 5 seconds before
reconnecting.
• Verify that the Biowall is
connected and operating.
• Ethernet cable is not damaged and
is less than 100 feet
• Make sure you have the correct
type of Ethernet cable
• Verify that Ethernet cable is not
too close to an electric motor,
microwave, router, etc that may
cause interference
Screen not responding to touch
• Ethernet cable is disconnected
• Screen is defective
• Disconnect power to the screen,
wait 5 seconds before
reconnecting
• Contact Sanuvox
Screen displays a red X on black
background
• An error happened during the
memory card start up
• Disconnect power to the screen,
wait 5 seconds before
reconnecting
Screen displays LMPH as lamp type
• Wrong lamp type was
programmed
• Contact Sanuvox for instructions
The following icon appears for all lamps
• Access door is open
• No signal is received on the PLC
board
• Fans are not working in ballast box
• Make sure the access door is
closed tightly or that a cable is
hooked up on the SW
• Make sure that 24VDC is present
on the PLC or that the switch is on
BP mode
• Make sure the fans are hooked up
and that they can turn without any
restrictions
The following icon appears on one or
more lamps
• Lamp or ballast failure
• Change a working lamp with the
defective lamp to confirm a lamp
out or ballast out
The following icon appears
• Lamp has been on for more than 2
years
• Replace lamp and the press on icon
to select the lamp than
press on to reset the
counter
The following icon appears
• Both have are not working
• Both fans are not wired properly
• Make sure both fans can turn
without restrictions
• Both fans are defective
• Make sure the fans are wired
correctly
• Contact Sanuvox to order new fans
Non
Oui
Oui
Début
Est-ce que L’écran
affiche quelque chose ?
Est-ce que l’écran
affiche “Drive not
mounted”
Est-ce qu’une
alimentation 5 VDC
1.5A est correctement
branché ?
Non
Vérifier qu’une
alimentation adéquate
est présente
Appeler Sanuvox
Appelez Sanuvox
Oui
Est-ce que l’écran affiche “Check the
communication cable” ou “No data
transfert detected” ?
Non
Débrancher l’alimentation
de l’écran. Attendre 5
secondes avant de le
rebrancher
Est-ce que l’écran affiche “Check
the communication cable” ou “No
data transfert detected” ?
Est-ce qu’un cable ethernet
non-croisé (RJ45) est utilisé
entre l’écran et le Biowall ?
Est-ce que le cable est en bon
état et mesure moins de 30
mètres ?
Oui
Appeler Sanuvox
Oui
Non
Est-ce que l’écran tactile
répond au touché ?
Débrancher l’alimentation
de l’écran. Attendre 5
secondes avant de le
rebrancher
Est-ce que l’écran tactile
répond au touché ?
Appeler Sanuvox
Non
Est-ce que l’écran affiche une
croix rouge sur un fond noir ?
Oui
Non
Oui
Est-ce que l’écran affiche
“LMPH” pour identifier un type
de lampe ?
Non
Oui
Utiliser un cable ethernet
non-croisé (RJ45)
mesurant au maximum 30
mètres
Est-ce que le Biowall est
allumé ?
Oui
Allumer le Biowall
Non
Oui
Oui
Non
Fin
Non
Non
Non
&
Step&by&Step&
Autres manuels pour Bio-Wall MAX
2
Autres manuels Sanuvox écran tactile
Manuels écran tactile populaires d'autres marques
Elecro Engineering
Elecro Engineering Poolsmart Plus Instructions d'installation
Johnson Controls
Johnson Controls IQ4 HUB Manuel utilisateur
Elo TouchSystems
Elo TouchSystems ET2270L Manuel utilisateur
Elo TouchSystems
Elo TouchSystems ET1002L Manuel utilisateur
Elo TouchSystems
Elo TouchSystems 3201L Manuel utilisateur
Duratec
Duratec S15 Manuel utilisateur
