Samson 3347-1 Manuel de service
Translation of original instructions
EB 8097 EN
Type3347-7, cast body with welding
ends
Type3347-7, bar stock body with
threaded connections
Edition May 2016
Type3347-1 and Type3347-7 Pneumatic Control Valves
Note on these mounting and operating instructions
These mounting and operating instructions assist you in mounting and operating the device
safely. The instructions are binding for handling SAMSON devices.
ÎFor the safe and proper use of these instructions, read them carefully and keep them for
later reference.
ÎIf you have any questions about these instructions, contact SAMSON‘s After-sales Service
Department (aftersalesser[email protected]).
The mounting and operating instructions for the devices are included in
the scope of delivery. The latest documentation is available on our website
at www.samson.de > Service & Support > Downloads > Documentation.
Denition of signal words
Hazardous situations which, if not avoided,
will result in death or serious injury
Hazardous situations which, if not avoided,
could result in death or serious injury
Property damage message or malfunction
Additional information
Recommended action
DANGER
!
WARNING
!
NOTICE
!
Note
Tip
2 EB 8097 EN
Contents
EB 8097 EN 3
1 General safety instructions.............................................................................4
2 Design and principle of operation ..................................................................6
3 Assembling valve and actuator ......................................................................9
3.1 Assembly and adjustment ...............................................................................9
3.2 Option of preloading springs for "actuator stem extends"................................10
3.3 Different rated travels of valve and actuator ...................................................10
4 Installation..................................................................................................11
4.1 Notes on installation ....................................................................................11
4.2 Signal pressure line ......................................................................................11
5 Operation...................................................................................................11
6 Maintenance ...............................................................................................12
6.1 Replacing sealing parts and plug ..................................................................12
7 Description of nameplates............................................................................14
8 Inquiries .....................................................................................................15
4 EB 8097 EN
General safety instructions
1 General safety instructions
−The control valve must be mounted, started up, or serviced by fully trained
and qualied personnel only; the accepted industry codes and practices
are to be observed. Make sure employees or third persons are not ex-
posed to any danger. All safety instructions and warnings given in these
mounting and operating instructions, particularly those concerning installa-
tion, start-up and maintenance, must be strictly observed.
−The control valves comply with the requirements of the European Pressure
Equipment Directive 2014/68/EU. Valves with a CE marking have a
declaration of conformity which includes information about the applied
conformity assessment procedure.
The declaration of conformity can be viewed and downloaded at
http://www.samson.de.
−To ensure appropriate use, only use the valve in applications where the op-
erating pressure and temperatures do not exceed the specications used
for sizing the valve at the ordering stage. The manufacturer does not as-
sume any responsibility for damage caused by external forces or any other
external factors.
−Any hazards that could be caused in the valve by the process medium, the
operating pressure, the signal pressure or by moving parts are to be pre-
vented by taking appropriate precautions.
−Proper shipping and storage are assumed.
−For installation and maintenance, make sure the relevant section of the
pipeline is depressurized and, depending on the process medium, drained
as well. Depending on the eld of application, allow the valve to cool
down or heat up to reach ambient temperature before starting any work
on it.
−When working on the valve, make sure that the pneumatic air supply as
well as the control signal are disconnected to prevent any hazards caused
by moving parts.
−Be particularly careful if the actuator springs are preloaded. Such actua-
tors are labeled correspondingly and can also be identied by three long
bolts protruding from the bottom of the actuator. Before starting any work
on the valve, relieve the compression from the preloaded springs.
EB 8097 EN 5
General safety instructions
According to the ignition risk assessment performed in accordance with EN13463-1:2009,
section 5.2, the non-electrical control valves do not have their own potential ignition source
even in the rare incident of an operating fault. As a result, they do not fall within the scope of
Directive 2014/34/EU.
ÎFor connection to the equipotential bonding system, observe the requirements specied in
section 6.4 of EN60079-14 (VDE0165 Part 1).
6 EB 8097 EN
Design and principle of operation
2 Design and principle of oper-
ation
The Type3347 Angle Valve can be com-
bined with either a Type3271 Pneumatic
Actuator or a Type3277 Pneumatic Actuator
with integral positioner attachment.
The standard valve body is designed for
welding into pipelines. Other versions can
be equipped with threaded or anged ends,
or clamp connections.
The control valve is tted with an easily de-
tachable clamp connection between valve
body and bonnet. The body free of dead
space is suitable for CIP (Cleaning-In-Place).
The control valves are mainly designed for
use as control or on/off valves in the food
industry.
The medium ows through the valve in the
direction indicated by the arrow. The plug
(3) is moved by changing the signal pressure
acting on the diaphragm of the actuator.
The plug stem (6) with plug (3) and actuator
stem (8.1) are connected by the stem con-
nector (7) and sealed by a PTFE seals (5.1
and 5.3).
In the special version with steam line connec-
tion, an additional spring-loaded PTFE ring
packing (4.2) is used. In this case, the plug
stem can be cleaned through the connection
of a steam line.
Fail-safe position
Depending on how the compression
springs(8.3) are arranged in the actuator,
the valve has two different fail-safe positions:
−Actuator stem extends: when the signal
pressure is reduced or the air supply
fails, the springs move the actuator stem
downward and close the valve.
The valve opens when the signal pressure
is increased enough to overcome the
force exerted by the springs.
−Actuator stem retracts: when the signal
pressure is reduced or the air supply
fails, the springs move the actuator stem
upward and open the valve.
The valve closes when the signal pressure
is increased enough to overcome the
force exerted by the springs.
Legend for Fig.1
1 Valve body
1.1 Centering ring
1.2 Body gasket
1.3 Compensating ring
3 Plug
4.1 Spring (special version)
4.2 Packing (special version)
4.3 Washers (special version)
5 Valve bonnet
5.1 Stem seal
5.2 Body and stem seal
5.3 Wiper ring
5.4 Clamp
5.5 Travel indicator scale
6 Plug stem
6.1 Stem connector nut
6.2 Lock nut
7 Stem connector
8 Actuator
8.1 Actuator stem
8.2 Ring nut
8.3 Compression springs
9Signal pressure
connection
10 Compression-type tting
EB 8097 EN 7
Design and principle of operation
6.1
6.2
6
1.3
8
8.3
8.2
8.1
5.5
7
5
5.3
5.4
5.2
3
1
9
8
8.1
5
8.2
10
4.2
5.1
5.4
1.2
1.1
4.3
6.2
6
5.3
4.1
4.3
3
1
Special version with steam line connection
Version with cast body
Type3277 ActuatorType3271 Actuator
Fig.1: Sectional drawings
8 EB 8097 EN
Design and principle of operation
Compliance
The Type3347 Valve bears the EAC mark of
conformity:
EB 8097 EN 9
Assembling valve and actuator
3 Assembling valve and actua-
tor
The basic pneumatic actuator can be re-
placed by a pneumatic actuator with addi-
tional handwheel or by an electric actuator.
The standard pneumatic actuator can be re-
placed by a smaller or larger actuator for all
nominal valve sizes.
If the travel range of the actuator is larger
than the travel of the valve, the springs in the
actuator are preloaded by SAMSON so that
the travel ranges match.
3.1 Assembly and adjustment
Proceed as follows if the valve and actuator
have not been assembled by SAMSON or if
the actuator is to be replaced by an actuator
of another type or size:
1. Loosen the lock nut (6.2) and stem con-
nector nut (6.1) on the valve. Firmly
press the plug together with the plug
stem into the seat. Thread down the lock
nut and stem connector nut.
2. Remove the clamps of the stem connector
(7) and the ring nut (8.2) from the actua-
tor (8).
3. Slide the ring nut over the plug stem.
4. Place the actuator onto the valve bonnet
(5) and secure it with the ring nut (8.2).
5. Read the bench range (e.g.0.2 to 1bar)
and the actuator's fail-safe action (e.g.
"actuator stem extends") from the actua-
tor's nameplate.
The fail-safe action "actuator stem ex-
tends" or "actuator stem retracts" is
marked by FA or FE on the Type3271
Actuator, and by a corresponding sym-
bol on the nameplate of the Type3277
Actuator.
The lower value corresponds to the lower
bench range value to be adjusted,
whereas the upper value corresponds the
upper bench range value.
During assembly, make sure that the stem
seal (5.1) is not damaged.
The maximum possible actuator travel must
not exceed the maximum permissible valve
travel (see adhesive label on the yoke).
6. For actuators with "actuator stem ex-
tends" fail-safe action, apply a signal
pressure that corresponds to the lower
bench range value (e.g. 0.2 or 0.4bar)
to the connection on the bottom dia-
phragm chamber.
For actuators with "actuator stem re-
tracts" fail-safe action, apply a signal
pressure that corresponds to the upper
bench range value (e.g. 1bar) to the
connection on the top diaphragm cham-
ber.
7. Screw on the stem connector nut (6.1) by
hand until it touches the actuator stem
(8.1). Turn it a further ¼turn and secure
this position with the lock nut (6.2)
8. Position clamps of the stem connector (7)
and screw them tight.
NOTICE
!
10 EB 8097 EN
Assembling valve and actuator
9. Align travel indicator scale (5.5) with the
tip of the stem connector; for actuators
with fail-safe action "actuator stem ex-
tends" align it with lower marking (valve
closed) and for actuators with fail-safe
action "actuator stem retracts" align it
with top marking (valve open).
Note on removing an actuator
When removing an actuator with "stem ex-
tends" fail-safe action from a valve and es-
pecially an actuator with preloaded springs,
apply a signal pressure that is slightly higher
than the lower bench range value (see actu-
ator nameplate) to the lower signal pressure
connection to allow the ring nut (8) to be
loosened.
3.2 Option of preloading
springs for "actuator stem
extends"
To achieve a greater positioning force, the
springs of the actuators can be preloaded by
up to 25% of their travel or their bench
range.
When a preload of, e.g. 0.1bar, is desired
for a bench range of0.2 to 1bar, the lower
bench range value is shifted by 0.1bar to
0.3bar (0.1bar correspond to a preload of
12.5%).
When adjusting the valve, set the lower
bench range value to 0.3bar. Write the new
bench range with preloaded springs of 0.3
to 1.1bar on the nameplate.
3.3 Different rated travels of
valve and actuator
Actuators that have already been preloaded
by the manufacturer without mounting the
valve are labeled correspondingly. Addition-
ally, they can be identied by three longer
bolts with nuts protruding from the bottom
diaphragm case.
Always use actuators with preloaded springs
when the valve's rated travel is smaller than
the rated travel of the actuator.
GEFAHR
!WARNING
!
NOTICE
!
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Samson Unité de contrôle
Samson
Samson 3522 Manuel de service
Samson
Samson 3251 Manuel de service
Samson
Samson 42-10 RS Manuel de service
Samson
Samson 763 Manuel du propriétaire
Samson
Samson 2406 Manuel de service
Samson
Samson TROVIS I/O Manuel utilisateur
Samson
Samson EB 3963 EN Manuel de service
Samson
Samson 3251 Manuel de service
Samson
Samson 2357-1 Manuel de service
Samson
Samson BR14b Manuel utilisateur
Samson
Samson 3244 Manuel de service
Samson
Samson 3251-E Manuel de service
Samson
Samson 36-3 Guide de configuration
Samson
Samson 2335 Manuel de service
Samson
Samson 3323 Manuel de service
Samson
Samson 3254 Manuel de service
Samson
Samson 3711 Manuel de service
Samson
Samson 3241-1-Gas Manuel de service
Samson
Samson 41-23 Series Manuel de service
Samson
Samson 2489/58 Series Manuel de service
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
