Samson 2405 Series Manuel de service

Mounting and

Operating Instructions

EB 2520 EN

Translation of original instructions

Edition June 2017

Self-operated Pressure Regulators

Type2405 Pressure Reducing Valve

2 EB 2520 EN

Note on these mounting and operating instructions

These mounting and operating instructions assist you in mounting and operating the device

safely. The instructions are binding for handling SAMSON devices.

ÎFor the safe and proper use of these instructions, read them carefully and keep them for

later reference.

ÎIf you have any questions about these instructions, contact SAMSON‘s After-sales Service

Department (aftersalesser[email protected]).

The mounting and operating instructions for the devices are included in

the scope of delivery. The latest documentation is available on our website

(www.samson.de) > Product documentation. You can enter the document

number or type number in the [Find:] eld to look for a document.

Denition of signal words

Hazardous situations which, if not avoided,

will result in death or serious injury

Hazardous situations which, if not avoided,

could result in death or serious injury

Property damage message or malfunction

Additional information

Recommended action

DANGER

WARNING

NOTICE

Note

Tip

Contents

EB 2520 EN 3

1 Safety instructions and measures ...................................................................5

1.1 Notes on possible severe personal injury .........................................................7

1.2 Notes on possible personal injury ...................................................................7

1.3 Notes on possible property damage................................................................8

2 Markings on the device .................................................................................9

3 Design and principle of operation ................................................................10

3.1 Versions ......................................................................................................11

3.2 Technical data .............................................................................................12

4 Measures for preparation............................................................................16

4.1 Unpacking ..................................................................................................16

4.2 Transporting and lifting ................................................................................16

4.3 Storage.......................................................................................................16

4.4 Preparation for installation............................................................................17

5 Mounting and start-up.................................................................................18

5.1 Installing the valve into the pipeline ...............................................................18

5.1.1 Installation conditions...................................................................................18

5.1.2 Mounting position........................................................................................18

5.1.3 Additional ttings.........................................................................................19

5.2 Quick check ................................................................................................20

5.3 Putting the regulator into operation................................................................21

5.4 Adjusting the set point..................................................................................21

6 Servicing.....................................................................................................22

6.1 Preparation for return shipment.....................................................................22

6.2 Ordering spare parts and operating supplies .................................................23

7 Malfunctions ...............................................................................................24

7.1 Troubleshooting ...........................................................................................24

8 Decommissioning and disassembly ..............................................................25

8.1 Decommissioning.........................................................................................25

8.2 Removing the valve from the pipeline.............................................................25

8.3 Disposal......................................................................................................25

4 EB 2520 EN

Contents

9 Annex.........................................................................................................26

9.1 After-sales service........................................................................................26

9.2 Certicates ..................................................................................................26

EB 2520 EN 5

Safety instructions and measures

1 Safety instructions and measures

Intended use

The Type2405 Pressure Reducing Valve is used to control the pressure of ammable gases

used as a source of energy, e.g. in boilers, driers, vaporizers, heat exchangers or industrial

ovens. Alternatively, it can control the compressed air supply in process engineering applica-

tions.

The device is designed to operate under exactly dened conditions (e.g. operating pressure,

process medium, temperature). Therefore, operators must ensure that the device is only used

in applications that meet the specications used for sizing the device at the ordering stage. In

case operators intend to use the device in other applications or conditions than specied,

contact SAMSON.

SAMSON does not assume any liability for damage resulting from the failure to use the de-

vice for its intended purpose or for damage caused by external forces or any other external

factors.

ÎRefer to the technical data and nameplate for limits and elds of application as well as

possible uses.

Reasonably foreseeable misuse

The device is not suitable for use outside the limits dened during sizing and in the technical

data. Furthermore, the following activities do not comply with the intended use:

−Use as safety valve

−Use of non-original spare parts

−Performing service and repair work not described in these instructions

Qualications of operating personnel

The device must be mounted, started up, serviced, and repaired by fully trained and quali-

ed personnel only; the accepted industry codes and practices are to be observed. Accord-

ing to these mounting and operating instructions, trained personnel refers to individuals who

are able to judge the work they are assigned to and recognize possible hazards due to their

specialized training, their knowledge and experience as well as their knowledge of the appli-

cable standards.

6 EB 2520 EN

Safety instructions and measures

Personal protective equipment

We recommend wearing the following protective equipment depending on the process medi-

um:

−Protective clothing, gloves, and eyewear in applications with hot, cold, and/or corrosive

media

ÎCheck with the plant operator for details on further protective equipment.

Revisions and other modications

Revisions, conversions or other modications to the product are not authorized by SAMSON.

They are performed at the user's own risk and may lead to safety hazards, for example. Fur-

thermore, the product may no longer meet the requirements for its intended use.

Warning against residual hazards

To avoid personal injury or property damage, operators and operating personnel must pre-

vent hazards that could be caused in the device by the process medium and operating pres-

sure by taking appropriate precautions. They must observe all hazard statements, warning

and caution notes in these mounting and operating instructions, especially for installation,

start-up, and service work.

Responsibilities of the operator

The operator is responsible for proper operation and compliance with the safety regulations.

Operators are obliged to provide these mounting and operating instructions as well as the

referenced documents to the operating personnel and to instruct them in proper operation.

Furthermore, the operator must ensure that operating personnel or third persons are not ex-

posed to any danger.

Responsibilities of operating personnel

Operating personnel must read and understand these mounting and operating instructions as

well as the referenced documents and observe the hazard statements, warning and caution

notes specied in them. Furthermore, the operating personnel must be familiar with the ap-

plicable health, safety and accident prevention regulations and comply with them.

Referenced standards and regulations

The devices comply with the requirements of the European Pressure Equipment Directive

2014/68/EU. Devices with a CE marking have an EU declaration of conformity, which in-

cludes information about the applied conformity assessment procedure. This declaration of

conformity is included in the Appendix of these instructions (see section9.2).

EB 2520 EN 7

Safety instructions and measures

Non-electric valve versions whose bodies are not lined with an insulating material coating do

not have their own potential ignition source according to the risk assessment stipulated in

EN13463-1:2009, section5.2, even in the rare incident of an operating fault. Therefore,

such valve versions do not fall within the scope of Directive 2014/34/EU.

ÎFor connection to the equipotential bonding system, observe the requirements specied in

section 6.4 of EN60079-14 (VDE0165 Part 1).

1.1 Notes on possible severe personal injury

DANGER

Risk of bursting in pressure equipment.

Control valves and pipelines are pressure equipment. Improper opening can lead to

valve components bursting.

ÎBefore starting any work on the control valve, depressurize all plant sections con-

cerned as well as the valve.

ÎTo prevent uncontrolled excess pressure, make sure that suitable overpressure pro-

tection is installed on site in the plant section.

ÎDrain the process medium from all the plant sections concerned as well as the

valve.

ÎWear personal protective equipment.

1.2 Notes on possible personal injury

WARNING

Risk of personal injury due to residual process medium in the valve.

While working on the valve, residual process medium can escape and, depending on

its properties, may lead to personal injury, e.g. (chemical) burns.

ÎIf possible, drain the process medium from all the plant sections concerned and the

valve.

ÎWear protective clothing, safety gloves, and eyewear.

8 EB 2520 EN

Safety instructions and measures

WARNING

Risk of burn injuries due to hot or cold components and pipelines.

Depending on the process medium, valve components, and pipelines may get very hot

or cold and cause burn injuries.

ÎAllow components and pipelines to cool down or heat up.

ÎWear protective clothing and safety gloves.

Damage to health relating to the REACH regulation.

If a SAMSON device contains a substance which is listed as being a substance of very

high concern on the candidate list of the REACH regulation, this circumstance is indi-

cated on the SAMSON delivery note.

ÎInformation on safe use of the part affected, see uhttp://www.samson.de/reach-

en.html.

1.3 Notes on possible property damage

NOTICE

Risk of valve damage due to contamination (e.g. solid particles) in the pipeline.

The plant operator is responsible for cleaning the pipelines in the plant.

ÎFlush the pipelines before start-up.

ÎObserve the maximum permissible pressure for valve and plant.

Risk of valve damage due to unsuitable medium properties.

The valve is designed for a process medium with dened properties.

ÎOnly use the process medium specied for sizing the valve.

EB 2520 EN 9

Safety instructions and measures

NOTICE

Risk of leakage and valve damage due to excessively high or low tightening

torques.

Observe the specied torques on tightening valve components.

Excessively tightened torques lead to parts wearing out quicker. Parts that are too loose

may cause leakage.

ÎObserve the specied tightening torques.

Risk of regulator damage due to incorrectly attached lifting equipment.

ÎDo not attach lifting equipment to mounting parts (e.g. adjusting screw or control

line).

Conversion from chromate coating to iridescent passivation

We at SAMSON are converting the surface treatment of passivated steel parts in our produc-

tion. As a result, you may receive a device assembled from parts that have been subjected to

different surface treatment methods. This means that the surfaces of some parts show differ-

ent reections. Parts can have an iridescent yellow or silver color. This has no effect on corro-

sion protection. For further information go to uwww.samson.de/chrome-en.html.

Note

10 EB 2520 EN

Markings on the device

2 Markings on the device

SAMSON

231

789 11

10 Made in Germany

2009

xxxx

1 Type designation (2405)

2 Max. perm. operating pressure at the

actuator pmax

3Conguration ID

4 Order number or date

5 KVS coefcient

7 Set point range/spring force

8 Nominal size

9 Nominal pressure

10 Permissible differential pressure (across

the valve)

11 Perm. temperature

12 Body material

The CE marking only exists for versions in nominal sizes DN32 to 50.

Fig.1: Nameplate

Note

Autres manuels pour 2405 Series

Table des matières

Autres manuels Samson Unité de contrôle

Samson

Samson 44-6 B Manuel de service

Samson

Samson 3241-1-Gas Manuel de service

Samson

Samson 3347-1 Manuel de service

Samson

Samson 2488/5 Series Manuel de service

Samson

Samson 1065 Manuel d'utilisation

Samson

Samson 3351 Manuel de service

Samson

Samson EB 8139 EN Manuel de service

Samson

Samson 3214 Manuel de service

Samson

Samson 2422 series Manuel de service

Samson

Samson EB 14b Manuel de service

Samson

Samson 3331/BR 31a Manuel de service

Samson

Samson 3241 Manuel utilisateur

Samson

Samson 3321CT Manuel de service

Samson

Samson 3281 Manuel de service

Samson

Samson Pfeiffer BR Series Manuel utilisateur

Samson

Samson Media 5 Manuel de service

Samson

Samson 42-36 E Manuel de service

Samson

Samson BR 26l Manuel utilisateur

Samson

Samson 2488 N Manuel de service

Samson

Samson 3354 Manuel de service

Samson

Samson 33-7 Manuel de service

Samson

Samson 3251 Manuel de service

Samson

Samson 3310/AT Manuel de service

Samson

Samson TROVIS 5100 Manuel de service

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur