Ruijie RG-WLAN Series Manuel utilisateur

RG-WLAN Series Access Point

RGOS Configuration Guide, Release 11.1(5)B8

Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup, modification,

transmission, translation or commercial use of this document or any portion of this document, in any form or by any means,

without the prior written consent of Ruijie Networks is prohibited.

, , , , ,

, , , ,

, , are registered trademarks of Ruijie Networks.

Counterfeit is strictly prohibited.

Exemption Statement

This document is provided “as is”. The contents of this document are subject to change without any notice. Please obtain

the latest information through the Ruijie Networks website. Ruijie Networks endeavors to ensure content accuracy and will

not shoulder any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.

Preface

Thank you for using our products. This manual matches the RGOS Release 11.1(5)B8.

Audience

This manual is intended for:

Network engineers

Technical support and servicing engineers

Network administrators

Obtaining Technical Assistance

Ruijie Networks website: http://www.ruijienetworks.com/

Ruijie service portal: http://case.ruijienetworks.com

Related Documents

Documents

Description

Command Reference

Describes the related configuration commands, including command modes,

parameter descriptions, usage guides, and related examples.

Hardware Installation and Reference

Guide

Describes the functional and physical features and provides the device

installation steps, hardware troubleshooting, module technical specifications,

and specifications and usage guidelines for cables and connectors.

Conventions

This manual uses the following conventions:

Convention

Description

boldface font

Commands, command options, and keywords are in boldface.

italic font

Arguments for which you supply values are in italics.

[ ]

Elements in square brackets are optional.

{ x | y | z }

Alternative keywords are grouped in braces and separated by vertical bars.

[ x | y | z ]

Optional alternative keywords are grouped in brackets and separated by

vertical bars.

Symbols

Means reader take note. Notes contain helpful suggestions or references.

Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of

data.

RG-WLAN Series Access Point

RGOS Configuration Guide,

Release 11.1(5)B8

WLAN Basic Configuration

1. Configuring AP Management

2. Configuring STA Management

3. Configuring Ethernet Management

4. Configuring Data Plane

5. Configuring WLAN Log

Configuration Guide Configuring AP Management

1 Configuring AP Management

1.1 Overview

N/A

1.2 Application

N/A

1.3 Features

Basic Concepts

AP

AP is an access point used by wireless terminals to access a wired network. It is equivalent to a bridge for communication

between wireless terminals and a wired network.

1.4 Configuration

Configuration

Description and Command

Configuring the Fit or Fat AP

Mode

(Optional) The AP mode can be switched between the fit AP mode and the fat AP mode

according to requirements.

switch2fat

Switches the mode of a specified AP to the fat AP mode in

AC configuration mode on the AC device.

ap-mode

Configures the fit or fat AP mode in global configuration

mode on the AP device.

1.4.1 Configuring the Fit or Fat AP Mode

Configuration Effect

On the AC device, run the switch2fat command in AC configuration mode to switch the mode of an online AP to the fat

AP mode.

On the AC device, run the ap-mode command in global configuration mode to switch between the fit AP mode and the

fat AP mode.

Configuration Guide Configuring AP Management

Notes

N/A

Configuration Steps



On the AP device, run the ap-mode command in global configuration mode to switch between the fit AP mode and the

fat AP mode.

Command

ap-mode { fit | fat [ dhcp ] }

Parameter

Description

fit: indicates that the AP mode is switched to the fit AP mode.

fat: indicates that the AP mode is switched to the fat AP mode.

dhcp: If the ap-mode fat command contains this parameter, the AP obtains the IP address through DHCP

by default after the AP mode is switched to the fat AP mode; otherwise, the AP uses the static IP address by

default after the AP mode is switched to the fat AP mode.

Defaults

None

Command

Mode

AP global configuration mode

Usage Guide

After the AP mode is switched between the fit and fat AP modes, the AP must be restarted to ensure the

configuration consistency.

For WALL-APs supplied by Ruijie Networks, when the fat AP mode is used, the default IP address of

the rear wired network interface (connected to the PoE switching device) is

192.168.110.1/255.255.255.0, and the default IP address of the front wired network interface (Ethernet

interface) is 192.168.111.1/255.255.255.0.

If ap-mode fat dhcp is configured, when the AP mode is switched to the fat AP mode, the IP address

is obtained through DHCP by default. After the AP is restarted, if related configuration is not available,

the IP address is still obtained through DHCP by default. In addition, the following two issues should

also be noted:

1. If ap-mode fat dhcp is configured for the WALL-AP, only the IP address of the rear wired network

interface is obtained through DHCP, and the front wired network interface uses the static IP address by

default. 2. In fat AP mode, the ap-mode fat dhcp and ap-mode fat commands cannot be mutually

switched, and must be switched to the fit AP mode first.

Verification

On the AP, run the show ap-mode command to check the current mode of the AP.

Configuration Example

Switching the mode of the AP to the fit AP mode on the AP

Configuration

Enter the global configuration mode.

Configuration Guide Configuring AP Management

Steps

Run the ap-mode command.

Ruijie(config)#ap-mode fit

Verification

On the AP, run the show ap-mode command to check the current mode of the AP.

Ruijie#show ap-mode

current mode: fit

Common Errors

None

1.5 Monitoring

Displaying

Description

Command

Displays the fit or fat mode of the AP

show ap-mode

Configuration Guide Configuring STA Management

2 Configuring STA Management

2.1 Overview

STA Management (STAMG) implements station (STA) management, including STA access control management and STA

event notification. Event notification is mainly used to serve other function modules. Applications of the STAMG functions are

as follows:

The dynamic blacklist is used on a security-sensitive network to prevent user attacks.

The STA limit is used when the number of STAs exceeds the AP capacity.

Load balancing is used when STAs need to be evenly distributed to multiple APs.

Association control is used in the E-bag scenario.

Protocols and Standards

N/A

2.2 Applications

N/A

2.3 Features

Overview

Feature

Description

Association Control

Associates secondary STAs with APs in the same control zone if the primary STA is associated with

these APs.

2.3.1 Association Control

Association control is a method for controlling association behaviors of wireless STAs. STAs are divided into two groups. In

each group, only one STA is defined as the primary STA, and the other STAs are defined as secondary STAs. The

secondary STAs must follow the association behaviors of the primary STA. That is, the primary and secondary STAs must be

associated with the same wireless network. In this way, association behaviors of wireless STAs can be properly controlled.

Working Principle

The coverage area of a wireless network is divided into several association control zones. One or several APs are deployed

in each zone, and wireless terminals are divided into groups. The control zones that can be associated with the terminals are

strictly controlled. For example, a school has many classrooms, and a wireless AP is deployed in each classroom. Radio

Configuration Guide Configuring STA Management

signals travel in the space.When E-bags are used in two adjacent classrooms at the same time, the ideal condition is that all

the teacher and student terminals are associated with the AP of their own classrooms so that the two classrooms will not

interfere with each other. In this case, a classroom must be defined as an association control zone and all the teacher and

student terminals in a classroom must be associated with the AP of the classroom.

Association control aims to prevent terminals from associating with a wireless network at random when multiple wireless

networks are available for selection. The following are prerequisites for network configurations:

Based on the pre-configured association control zones and package information, the AC pushes the information about

primary STAs in all packages to all APs in the association control zones and generates a whitelist of primary STAs on

these APs.

The information about primary STAs in all packages is available in the AP whitelist. Therefore, before the association

control function is enabled, the primary STA must associate itself with the corresponding SSID in the specified control

zone. After that, the AC pushes all corresponding secondary STAs to all APs in the association control zone and

generates a whitelist according to the configuration of the primary STA package to allow the secondary STAs to

associate themselves with the control zone.

When the primary STA is de-associated from the control zone, all the secondary STAs will also be de-associated and

deleted from the AP whitelist.

The above process can be summarized as follows: The secondary STAs must follow the primary STA to associate

themselves with an AP in the same control zone, with which the primary STA is associated. Only the APs of this control

zone have a whitelist of the corresponding secondary STAs. This ensures that STAs are not randomly associated with

APs.

2.4 Configuration

Configuration

Description and Command

Configuring Association

Control

(Mandatory) It is used to enable the association control function.

package

Configures a package.

primary-sta

Configures the primary STA in the

package.

secondary-sta

Configures the secondary STA in the

package.

control-zone

Configures an association control zone.

Configures the AP information.

assoc-control

Enables association control.

2.4.1 Configuring Association Control

Configuration Effect

Secondary STAs must be associated with APs in the same group as the primary STA when being associated.

Autres manuels pour RG-WLAN Series

Table des matières

Autres manuels Ruijie Point d'accès sans fil

Ruijie

Ruijie Reyee RG-RAP2260(G) Manuel d'installation et d'exploitation

Ruijie

Ruijie RG-AP680-O Manuel utilisateur

Ruijie

Ruijie RG-AP720-L Series Manuel d'installation et d'exploitation

Ruijie

Ruijie RG-AP840-L Manuel d'installation et d'exploitation

Ruijie

Ruijie AP630 Series Guide d'installation

Ruijie

Ruijie RG-AP680-IO Manuel d'installation et d'exploitation

Ruijie

Ruijie RG-SAP825-SP Manuel d'installation et d'exploitation

Ruijie

Ruijie RG-AP820(AR) Manuel d'installation et d'exploitation

Ruijie

Ruijie Reyee RG-RAP Series Manuel utilisateur

Ruijie

Ruijie RG-AP820-L(V2) Series Manuel d'installation et d'exploitation

Ruijie

Ruijie RG-AP220 Series Manuel utilisateur

Ruijie

Ruijie RG-AP820-I Manuel d'installation et d'exploitation

Ruijie

Ruijie RG-AP680 CD Series Manuel d'installation et d'exploitation

Ruijie

Ruijie RG-AP840-I (V2) Manuel d'installation et d'exploitation

Ruijie

Ruijie Reyee RG-RAP2200 Manuel d'installation et d'exploitation

Ruijie

Ruijie RG-SAP150-SP-W Manuel d'installation et d'exploitation

Ruijie

Ruijie RG-AP630 Directional Manuel d'installation et d'exploitation

Ruijie

Ruijie RG-WLAN Series Manuel d'installation

Ruijie

Ruijie Reyee RG-RAP6202(G) Manuel d'installation et d'exploitation

Ruijie

Ruijie RG-AP680-CD Manuel d'installation et d'exploitation

Ruijie

Ruijie Reyee RG-RAP2200 Manuel d'installation et d'exploitation

Ruijie

Ruijie RG-AP720-I Manuel utilisateur

Ruijie

Ruijie Reyee RG-RAP1201 Manuel d'installation et d'exploitation

Ruijie

Ruijie RG-SAP825-SP Manuel d'installation et d'exploitation

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur