RIOTEC ILS6302ABQ Manuel utilisateur

1

Programming Quick Guide

-iLS6302ABQ/iLS6302ABM

Connecting the Scanner

Be sure that PC is turned OFF, before Connect scanner cable to the

PC USB port on the PC as below described, Ensure that all connections

are ready, and turn on your PC.

1. Please switch ON and charge scanner for 4~5 hours at first time

before use. Scanner switch shown on Fig. 2.

2. After switch ON, the Orange LED will flash following with 3

beep-sounds. The RED LED will be OFF while it links to cradle

within 2.4GHz radio range.

3. If RED LED is continual ON, please re-plug USB cable, then, scan

the 3 barcodes on the bottom of cradle sequentially. (Shown on

Fig. 3 From 1 to 3).

4. Charging issue: Cradle works as charger when putting scanner on

it. Even if the scanner's battery is full, the cradle will continue to

supply power to the scanner. We suggest you to remove scanner

from cradle when scanner is charged fully

*Note: Please install PL-2303 driver for iLS6302ABM

LED Indicator Information

Orange LED ON Full charged

Orange LED Flashing Charging / Low battery

Red LED ON Off line / out of service

Green LED ON Good read

Orange LED ON Good read (Batch mode)

Remark:

*When the battery power is too low, the Orange LED will flash

and beep once. Scanner should be charged immediately.

*If scanner shuts down it is recommended to charge it fully

before turning it back on.

*Under power-saving mode, there will not be LED indication when

charging.

Reset Configuration to Defaults

(scan from A1 to A2 for iLS6302ABQ or B1 to B3 for iLS6302ABM)

iLS6302ABQ iLS6302ABM

A1 B1

A2 B3

*Note: Please install PL-2303 driver for iLS6302ABM

There are two operating modes on the scanner

1.Data Transmission mode (Default)

It is a necessary to scan “clean memory data" when

switching between these two modes.

Within 2.4GHz radio ran

Beyond 2.4GHz radio ran

Data

read Transmit data to PC/terminal

directly

Save data into scanner’s memory,

scanner will transmit data to PC/

terminal automatically when back to

2.4GHz radio range.

Enter Data Stora

e mode

LED Green/ Oran

e LED flashes

followed by 3 beeps.

2.Data Stora

e mode (Batch Mode)

It is a necessary to scan “clean memory data" when switchin

between these two modes.

Data

read

Save data directly to scanner’s memory, It will transmit the data to PC/

terminal after you scan the Transmit memory data code. To delete

data please scan the Clean memory data code.

Enter Data Transmission mod

LED

reen/Oran

e LED flashes followed by 3 beeps.

Always Clean memory data before switchin

to Data Transmission

Mode.

Otherwise Red/ Orange LED will flash with one long beep and will not

switch modes.

Under Data storage Mode

The data can be keep or delete by option after transmit

Keep the data

(Default) Delete the data

ransmit memory data

Green/Oran

e LED Flashes followed by 3 beeps

Clean memory data

Green/Oran

e LED flashes followed by 3 beeps

The barcode data which is stored in the memory will be deleted.

2

Trigger Mode

Trigger always

(Trigger available at any time)

Trigger standard

(Trigger available, after data sent to the device)

(Default)

Transmission Speed

Transmission speed is dependent on your device. In order not to lose

data, please choose the correct speed. Middle-speed is the Default.

High-speed Ultra Slow-speed

transmission

1transmission

Middle-speed Ultra Slow-speed

Transmission

(Default)

2transmission

Slow-speed Ultra Slow-speed

Transmission 3transmission

Wireless Auto-connection

Wireless Auto-connection ON:

When out of range, it will keep trying to

connect to device, scanner will not enter

power-saving mode.

Wireless Auto-connection OFF:

When you are out of BT signal range, scanner

will stop sending auto-connection signal to

device after 2 minutes. During this time, it will

not enter power-saving mode.

Once you are back within range, press trigger to

connect to the device. (Default)

Keyboard Country (For USB HID only)

Scan the appropriate country code as below to program the keyboard

layout for your country or language. As a general rule, the following

characters are supported, but need special care for countries other

than the United States: @ | $ # { } [ ] = / ‘ \ < > ~

USA

(Original setting) Italian

Norway France

Germany

ietnam

Sweden Spain

Denmar

Portu

Switzerland Hun

ary

Power-saving Mode

Power-saving mode OFF

Powe

-saving mode ON (Default):

Enter power-saving mode after 3-minute inactivity.

This function converses battery power. When you

press "SCAN/Power ON" button, it will wake up and

begin to scan.

Powe

-saving mode ON (Default):

Enter power-saving mode after 10-minute

inactivity. This function converses battery power.

When you press "SCAN/Power ON" button, it will

wake up and begin to scan.

*When charging, the scanner will not enter power-saving mode automatically.

How to append a “prefix” or a “suffix” to the

barcode data

prefix suffix

1. Scan above configuration code for Prefix or Suffix

2. Enter the required values (right, numeric barcode) for Prefix or

Suffix using the hex values for the desired HEX values from “Prefix

& Suffix TABLE (blew page)”

3. Then, end by scanning Code X (below, right)

*The max. of special characters is 5.

*When you append 1~4 required values for Prefix or Suffix, it must

end with Code X.

*It doesn’t need Code X, if you append 5 values to barcode data.

How to delete Prefix or Suffix

1. Scan above configuration code for Prefix or Suffix

2. Enter the “0” “0” (above, right)

3. Then end by scanning Code X (below, right)

Numeric barcode for settings

1 7

2 8

3 9

3

Prefix & Suffix TABLE

HEX HID

(SPP) HEX HID

(SPP) HEX HEX HEX HEX

01 CTRL A

(SOH) 19 CTRL Y

(EM) 20 SPACE 38 8 50 P 68 h

02 CTRL B

(STX) 1A CTRL

Z(SUB) 21 ! 39 9 51 Q69 i

03 CTRL C

(ETX) 1B ESC

(ESC) 22 " 3A : 52 R 6A j

04 CTRL D

(EOT) 1C CTRL \

(FS) 23 # 3B ; 53 S6B k

05 CTRL E

(ENQ) 1D CTRL ]

(GS) 24 $ 3C < 54 T 6C l

06 CTRL F

(ACK) 1E CTRL ^

(RS) 25 % 3D = 55 U6D m

07 CTRL G

(BEL) 1F CTRL _

(US) 26 & 3E > 56 V 6E n

08 Backspace

(BS) 27 ' 3F ? 57 W6F o

09 Tab

(HT) 28 ( 40 @ 58 X 70 p

0A CTRL J

(LF) 29 ) 41 A 59 Y71 q

0B CTRL K

(VT) 2A * 42 B 5A Z 72 r

0C CTRL L

(FF) 2B + 43 C 5B [73 s

0D Enter

(CR) 2C , 44 D 5C \ 74 t

0E CTRL N

(SO) 2D - 45 E 5D ]75 u

0F CTRL O

(SI) 2E . 46 F 5E ^ 76 v

10 CTRL P

(DLE) 2F / 47 G 5F _77 w

11 CTRL Q

(DC1) 30 0 48 H 60 ` 78 x

12 CTRL R

(DC2) 31 1 49 I 61 a79 y

13 CTRL S

(DC3) 32 2 4A J 62 b 7A z

14 CTRL T

(DC4) 33 3 4B K 63 c7B {

15 CTRL U

(NAK) 34 4 4C L 64 d 7C |

16 CTRL V

(SYN) 35 5 4D M 65 e7D }

17 CTRL W

(ETB) 36 6 4E N 66 f 7E ~

18 CTRL X

(CAN) 37 7 4F O 67 g

Redundancy Level

This scanner offers two levels of decode redundancy. Select higher

redundancy levels for decreasing levels of bar code quality.

As redundancy levels increase, the decoder’s aggressiveness

decreases.

Select the redundancy level appropriate for the bar code quality.

Redundancy Level 1

barcode must be successfully read twice

before being decoded

Redundancy Level 2

barcode must be successfully read three times

before being decoded:

1D Symbologies -1

ENABLE UPC-A DISABLE

ENABLE UPC-E DISABLE

ENABLE EAN-8 DISABLE

ENABLE EAN-13 DISABLE

ENABLE CODABAR DISABLE

1D Symbologies -2

ENABLE Code 39 DISABLE

ENABLE Code 39

FULL ASCII DISABLE

ENABLE

rioptic

Code 39 DISABLE

ENABLE Code 32 DISABLE

ENABLE CODE 93 DISABLE

ENABLE CODE 11 DISABLE

ENABLE Interleaved 25 DISABLE

ENABLE Discrete 25 DISABLE

ENABLE MSI DISABLE

4

1D Symbologies -3

ENABLE GS1 DataBar DISABLE

ENABLE GS1 DataBar

Limited DISABLE

ENABLE GS1 DataBar

Expanded DISABLE

ENABLE Composite

CC-C DISABLE

ENABLE Composite

CC-A/B DISABLE

ENABLE Composite

TLC 39 DISABLE

1D Symbologies -4

ENABLE Code 128 DISABLE

ENABLE ISBT 128 DISABLE

ENABLE Matrix 25 DISABLE

ENABLE Chinese 25 DISABLE

Quick guide is subject to change without notice. R_151103_05

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels RIOTEC Lecteur de codes-barres

RIOTEC

RIOTEC iLS6307LB Manuel utilisateur

RIOTEC

RIOTEC iDC9507A Manuel utilisateur

RIOTEC

RIOTEC RIOSCAN Manuel utilisateur

RIOTEC

RIOTEC iCR6300CBQ Manuel utilisateur

RIOTEC

RIOTEC DC9257LP Manuel utilisateur

RIOTEC

RIOTEC iLS6302NBU Manuel utilisateur

RIOTEC

RIOTEC DC9257AN Manuel utilisateur

RIOTEC

RIOTEC DC9250 Manuel utilisateur

RIOTEC

RIOTEC CR6307A Manuel utilisateur

RIOTEC

RIOTEC LS6320E Manuel utilisateur

RIOTEC

RIOTEC LS6300F Manuel utilisateur

RIOTEC

RIOTEC LS6308J Manuel utilisateur

RIOTEC

RIOTEC RIOSCAN iLS6308KS Manuel utilisateur

RIOTEC

RIOTEC iDC9273A Manuel utilisateur

RIOTEC

RIOTEC iLS6307JBQ Manuel utilisateur

RIOTEC

RIOTEC iDC9600K Manuel utilisateur

RIOTEC

RIOTEC OM7220L Manuel utilisateur

RIOTEC

RIOTEC OM7220J Manuel utilisateur

RIOTEC

RIOTEC LS6302A Manuel utilisateur

RIOTEC

RIOTEC iDC9278K Manuel utilisateur

RIOTEC

RIOTEC LS6300 Manuel utilisateur

RIOTEC

RIOTEC iLS6303XBU Manuel utilisateur

RIOTEC

RIOTEC iDC9607L Manuel utilisateur

RIOTEC

RIOTEC iLS6300VBU Manuel utilisateur

Manuels Lecteur de codes-barres populaires d'autres marques

POSMicro

POSMicro Datalogic PowerScan D7100 Manuel utilisateur

Marson

Marson MT780 Guide de configuration rapide

NCR

NCR RealPOS Manuel utilisateur

Motorola

Motorola SE3300 Guide de configuration rapide

Element

Element P130BT Manuel utilisateur

Motorola

Motorola Symbol LS3008 Manuel d'installation et d'exploitation

Meec tools

Meec tools OBD-II / VAG Manuel utilisateur

SICK

SICK CLP 100 Manuel utilisateur

Royal Tag SA

Royal Tag SA I-Read Manuel utilisateur

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuel utilisateur

Meteor

Meteor 8310 Manuel utilisateur

Denso

Denso BHT-500B Manuel utilisateur

Datalogic

Datalogic Heron HD3130 Manuel utilisateur

Motorola

Motorola MP6000 Instructions de montage

Newland

Newland NLS-HR15-BT Manuel utilisateur

ARTDEV

ARTDEV AS-1310 Manuel utilisateur

Aopos

Aopos AS290 Manuel utilisateur

ENS

ENS 367-5455 Manuel utilisateur

RIOTEC iLS6302ABQ Manuel utilisateur

Manuels Lecteur de codes-barres populaires d'autres marques