RIOTEC ILS6303XBU Manuel utilisateur

Programming Quick Guide

iLS6303XBU/iLS6303XB

Connecting the Scanner

Be sure that PC is turned OFF, before Connect scanner cable to

the PC USB port on the PC as below described, Ensure that all

connections are ready, turn on your PC

1. Please switch ON and charge scanner for 4~5 hours at first time

before use. Scanner switch shown on Fig. 2.

2. After switch ON, the Orange LED will flash following with 3

beep-sounds. The RED LED will be OFF while it links to cradle

within 2.4GHz radio range.

3. If RED LED is continual ON, please re-plug USB cable, then, scan

the 3 barcodes on the bottom of cradle sequentially. (Shown on

Fig. 3 from 1 to 3). If you are unable to complete this setting within

1 minute, please re-plug USB cable & re-start the scanner, and try

again.

4. Charging issue: Cradle works as charger when putting scanner on

it. Even if the scanner's battery is full, the cradle will continue to

supply power to the scanner. We suggest you to remove scanner

from cradle when scanner is charged fully

*Note: Please install PL-2303 driver for iLS6303XB

LED Indicator Information

Orange LED ON Full charged

Orange LED Flashing Charging / Low battery

Red LED ON Off line / out of service

Green LED ON Good read

Remark:

*When the battery power is too low, the Orange LED will flash

and beep once. Scanner should be charged immediately.

*If scanner shuts down it is recommended to charge it fully

before turning it back on.

*Under power-saving mode, there will not be LED indication

when charging.

Reset Configuration to Defaults

(scan from A1 to A2 for iLS6303XBU or B1 to B3 for iLS6303XB)

iLS6303XBU iLS6303XB

A1 B1



A2 B3

*Note: Please install PL-2303 driver for iLS6303XB

Trigger Mode

Trigger always

(Trigger available at any time)

Trigger standard (Default)

(Trigger available, after data sent to the

device)

Transmission Speed

Transmission speed is dependent on your device. In order not to lose

data, please choose the correct speed. Middle-speed is the Default.

High-speed Ultra Slow-speed

transmission

1transmission

Middle-speed Ultra Slow-speed

Transmission

(Default)

2transmission

Slow-speed Ultra Slow-speed

Transmission 3transmission

Wireless Auto-connection

Wireless Auto-connection ON:

When out of range, it will keep trying to

connect to device, scanner will not enter

power-saving mode.

Wireless Auto-connection OFF:

When you are out of BT signal range, scanner will

stop sending auto-connection signal to device

after 2 minutes. During this time, it will not enter

power-saving mode.

Once you are back within range, press trigger to

connect to the device. (Default)

1

Keyboard Country(For USB HID only)

Scan the appropriate country code as below to program the keyboard for

your country or language. As a general rule, the following characters are

not supported by the scanner for countries other than the United States:

@ | $ # { } [ ] = / ‘ \ < > ~

USA

(Original setting)

Italian

Norway

France

Germany

Vietnam

Sweden

Spain

Denmark

Portugal

Switzerland Hungary

Power-saving Mode

Power-saving mode OFF

Power-saving mode ON (Default):

Enter power-saving mode after 3-minute

inactivity. This function converses battery power.

When you press "SCAN/Power ON" button, it will

wake up and begin to scan.

Power-saving mode ON (Default):

Enter power-saving mode after 10-minute

inactivity. This function converses battery power.

When you press "SCAN/Power ON" button, it will

wake up and begin to scan.

*When charging, the scanner will not enter power-saving mode

automatically.

How to append a “prefix” or a “suffix” to the

barcode data

prefix suffix

1. scan above configuration code for Prefix or Suffix

2. enter the required values (right, numeric barcode) for Prefix or

Suffix using the hex values for the desired HEX values from “Prefix

& Suffix TABLE (blew page)”

3. then, end by scanning Code X (below, right)

*The max. of special characters is 5.

*When you append 1~4 required values for Prefix or Suffix, it must

end with Code X.

*It doesn’t need Code X, if you append 5 values to barcode data.

How to delete Prefix or Suffix

1. scan above configuration code for Prefix or Suffix

2. enter the “0” “0” (above, right)

3. then end by scanning Code X (below, right)

Numeric barcode for settings

1 7

2 8

3 9

Prefix & Suffix TABLE

HEX HID

(SPP) HEX HID

(SPP) HEX HEX HEX HEX

01 CTRL A

(SOH) 19 CTRL Y

(EM) 20 SPACE 38 8 50 P 68 h

02 CTRL B

(STX) 1A CTRL

Z(SUB) 21 ! 39 951 Q 69 i

03 CTRL C

(ETX) 1B ESC

(ESC) 22 " 3A : 52 R 6A j

04 CTRL D

(EOT) 1C CTRL \

(FS) 23 # 3B ;53 S 6B k

05 CTRL E

(ENQ) 1D CTRL ]

(GS) 24 $ 3C < 54 T 6C l

06 CTRL F

(ACK) 1E CTRL ^

(RS) 25 % 3D =55 U 6D m

07 CTRL G

(BEL) 1F CTRL _

(US) 26 & 3E > 56 V 6E n

08 Backspace

(BS) 27 ' 3F ?57 W 6F o

09 Tab

(HT) 28 ( 40 @ 58 X 70 p

0A CTRL J

(LF) 29 ) 41 A59 Y 71 q

0B CTRL K

(VT) 2A * 42 B 5A Z 72 r

0C CTRL L

(FF) 2B + 43 C5B [ 73 s

0D Enter

(CR) 2C , 44 D 5C \ 74 t

0E CTRL N

(SO) 2D - 45 E5D ] 75 u

0F CTRL O

(SI) 2E . 46 F 5E ^ 76 v

10 CTRL P

(DLE) 2F / 47 G5F _ 77 w

11 CTRL Q

(DC1) 30 0 48 H 60 ` 78 x

12 CTRL R

(DC2) 31 1 49 I61 a 79 y

13 CTRL S

(DC3) 32 2 4A J 62 b 7A z

14 CTRL T

(DC4) 33 3 4B K63 c 7B {

15 CTRL U

(NAK) 34 4 4C L 64 d 7C |

16 CTRL V

(SYN) 35 5 4D M65 e 7D }

17 CTRL W

(ETB) 36 6 4E N 66 f 7E ~

18 CTRL X

(CAN) 37 7 4F O67 g

2

Reading Techniques

The view finder projects an aiming

beam that should be centered over the

bar code, but it can be positioned in

any direction for a good read.

*Hold the scanner over the bar code, pull the trigger, and center the

aiming beam on the bar code.

*The aiming beam is smaller when the scanner is closer to the code

and larger when it is farther from the code.

1D Symbologies On/OFF -1

ENABLE

Codabar DISABLE

ENABLE

Code 39 DISABLE

ENABLE Code 39

Full ASCII DISABLE

ENABLE Interleaved

2 of 5 DISABLE

3

ENABLE

NEC 2 of 5 DISABLE

1D Symbologies On/OFF -2

ENABLE Straight 2 of 5

Industrial DISABLE

ENABLE Straight 2 of 5

IATA DISABLE

ENABLE Matrix

2 of 5 DISABLE

ENABLE

Code 128 DISABLE

ENABLE

GS1-128 DISABLE

ENABLE

UPC-A DISABLE

ENABLE

UPC-E DISABLE

ENABLE

Code 11 DISABLE

ENABLE

Code 93 DISABLE

1D Symbologies On/OFF -3

ENABLE

Telepen DISABLE

ENABLE GS1 DataBar

Omnidirectional DISABLE

ENABLE GS1 DataBar

Limited DISABLE

ENABLE GS1 DataBar

Expanded DISABLE

ENABLE

MSI DISABLE

ENABLE Trioptic

Code DISABLE

ENABLE

EAN-13 DISABLE

ENABLE

EAN-8 DISABLE

ENABLE

Code 32 DISABLE

*If you are going to scan Code 32, Trioptic Code must be off.

4

2D Symbologies On/OFF

ENABLE

Codablock A DISABLE

ENABLE

Codablock F DISABLE

ENABLE

PDF 417 DISABLE

ENABLE Micro

PDF 417 DISABLE

ENABLE

QR Code DISABLE

ENABLE

Data Matrix DISABLE

ENABLE

MaxiCOde DISABLE

ENABLE

Aztec Code DISABLE

ENABLE Chinese Sensible

(Han Xin) Code DISABLE

Quick guide is subject to change without notice. Q_140902_06

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels RIOTEC Lecteur de codes-barres

RIOTEC

RIOTEC iLS6300VBQ Manuel utilisateur

RIOTEC

RIOTEC RIOSCAN iLS6303AS Manuel utilisateur

RIOTEC

RIOTEC iLS6302ABU Manuel utilisateur

RIOTEC

RIOTEC iDC9608K Manuel utilisateur

RIOTEC

RIOTEC iDC9600K Manuel utilisateur

RIOTEC

RIOTEC FS5102N Manuel utilisateur

RIOTEC

RIOTEC OM7220J Manuel utilisateur

RIOTEC

RIOTEC OM7320 Manuel utilisateur

RIOTEC

RIOTEC iCR6300CBQ Manuel utilisateur

RIOTEC

RIOTEC iLS6300DBQ Manuel utilisateur

RIOTEC

RIOTEC iLS6308KBU Manuel utilisateur

RIOTEC

RIOTEC iLS6300JBQ Manuel utilisateur

RIOTEC

RIOTEC iLS6300FBQ Manuel utilisateur

RIOTEC

RIOTEC DC9250 Manuel utilisateur

RIOTEC

RIOTEC iCR6307AB Manuel utilisateur

RIOTEC

RIOTEC FS5020E Manuel utilisateur

RIOTEC

RIOTEC RIOSCAN iLS6308KS Manuel utilisateur

RIOTEC

RIOTEC DC9257LP Manuel utilisateur

RIOTEC

RIOTEC iLS6300VBU Manuel utilisateur

RIOTEC

RIOTEC iDC9270D Manuel utilisateur

RIOTEC

RIOTEC iLS6303ABQ Manuel utilisateur

RIOTEC

RIOTEC DC9270D Manuel utilisateur

RIOTEC

RIOTEC iDC9502K Manuel utilisateur

RIOTEC

RIOTEC CR6327A Manuel utilisateur

Manuels Lecteur de codes-barres populaires d'autres marques

POSMicro

POSMicro Datalogic PowerScan D7100 Manuel utilisateur

Marson

Marson MT780 Guide de configuration rapide

NCR

NCR RealPOS Manuel utilisateur

Motorola

Motorola SE3300 Guide de configuration rapide

Element

Element P130BT Manuel utilisateur

Motorola

Motorola Symbol LS3008 Manuel d'installation et d'exploitation

Meec tools

Meec tools OBD-II / VAG Manuel utilisateur

SICK

SICK CLP 100 Manuel utilisateur

Royal Tag SA

Royal Tag SA I-Read Manuel utilisateur

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuel utilisateur

Meteor

Meteor 8310 Manuel utilisateur

Denso

Denso BHT-500B Manuel utilisateur

Datalogic

Datalogic Heron HD3130 Manuel utilisateur

Motorola

Motorola MP6000 Instructions de montage

Newland

Newland NLS-HR15-BT Manuel utilisateur

ARTDEV

ARTDEV AS-1310 Manuel utilisateur

Aopos

Aopos AS290 Manuel utilisateur

ENS

ENS 367-5455 Manuel utilisateur

RIOTEC iLS6303XBU Manuel utilisateur

Manuels Lecteur de codes-barres populaires d'autres marques