RIOTEC DC9257A Manuel utilisateur

Programming Quick Guide

-DC9257A:Docking Scanner

-DC9267A:Wearable Scanner

Docking Scanner:

Gently tap the trigger area at the middle of scanner, to enable the

scanner (for reading barcode)

Wearable Scanner:

Press the ring trigger to enable the scanner.

Up Side

Lower Side

The touch sensor area is around middle of the scanner as drawing shown.

Installation

They are Plug &Play USB (HID) devices. When plugged into your Android

OTG devices, it can be recognized as barcode scanner and begin to scan

the barcode. Before using scanner, make sure the smartphone or tablet

is fully charged. Open your APP, they can work as a keyboard input.

Reset Configuration to Defaults

If you are unsure of the scanner configuration or have scanned the

incorrect codes, please scan the “Default” barcode. This will reset the

scanner to its factory defaults. (scan from 1 to 7)

Barcode Configuration Method:

(Flow chart for setup procedure :)

Start

Configuration

End

Configuration

Keyboard Language (For USB HID only)

Scan the appropriate country code as below to program the keyboard

layout for your country or language. As a general rule, the following

characters are supported, but need special care for countries other

than the United States: @ | $ # { } [ ] = / ‘ \ < > ~

USA

(Original setting)

Japan

Denmark

Finland

France

Germany

Italy

Norway

1D Symbologies – 1

ENABLE

CODE 39

DISABLE

ENABLE

CODE 39 Transmit

Start/Stop Character

DISABLE

ENABLE

CODE 39

FULL ASCII

DISABLE

ENABLE

CODE 11

DISABLE

Trigger

Area

Barcode Configuration Method:

(Flow chart for setup procedure :)

Start

Configuration

End

Configuration

1D Symbologies – 2

ENABLE

MSI

DISABLE

ENABLE

EAN-8

DISABLE

ENABLE

EAN-13

DISABLE

ENABLE

UPC-E

DISABLE

1D Symbologies – 3

ENABLE

UPC-A

DISABLE

ENABLE

Interleaved

DISABLE

ENABLE

Matrix

DISABLE

ENABLE

Industrial 25

DISABLE

ENABLE

CODE 93

DISABLE

ENABLE

CODABAR

DISABLE

ENABLE

CODE 128

DISABLE

ENABLE

GS1-128

UCC/EAN-128

DISABLE

ENABLE

GS1-Databar

(RSS)

DISABLE

1D Symbologies – 4

ENABLE

GS1-Databar

(RSS-Limited)

DISABLE

ENABLE

GS1-Databar

(RSS-Expand)

DISABLE

ENABLE

ISSN

DISABLE

ENABLE

ISBN

DISABLE

Inter-Keystroke Delay (FOR USB HID Only)

This parameter specifies the delay between emulated keystrokes

No Delay

Short Delay

(5ms)

Medium Delay

(10ms)

Long Delay

(15ms)



Information in this document is subject to change without notice.

R_151117_01

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels RIOTEC Lecteur de codes-barres

RIOTEC

RIOTEC LS6300J Manuel utilisateur

RIOTEC

RIOTEC iDC92700 Manuel utilisateur

RIOTEC

RIOTEC DC9277L Manuel utilisateur

RIOTEC

RIOTEC iCR6307AB Manuel utilisateur

RIOTEC

RIOTEC iDC9277L Manuel utilisateur

RIOTEC

RIOTEC FS5100D Manuel utilisateur

RIOTEC

RIOTEC LS6300 Manuel utilisateur

RIOTEC

RIOTEC RIOSCAN iCR6307AS Manuel utilisateur

RIOTEC

RIOTEC CR6327A Manuel utilisateur

RIOTEC

RIOTEC iLS6303XBQ Manuel utilisateur

RIOTEC

RIOTEC RIOSCAN iLS6303XS Manuel utilisateur

RIOTEC

RIOTEC iLS6302J BQ Manuel utilisateur

RIOTEC

RIOTEC iLS6303ABQ Manuel utilisateur

RIOTEC

RIOTEC FS5027L Manuel utilisateur

RIOTEC

RIOTEC DC9257L Manuel utilisateur

RIOTEC

RIOTEC LS6300E Manuel utilisateur

RIOTEC

RIOTEC DC9270D Manuel utilisateur

RIOTEC

RIOTEC LS6307L Manuel utilisateur

RIOTEC

RIOTEC CR6307A Manuel utilisateur

RIOTEC

RIOTEC RIOSCAN iLS6303AS Manuel utilisateur

RIOTEC

RIOTEC iDC9273A Manuel utilisateur

RIOTEC

RIOTEC iDC9607L Manuel utilisateur

RIOTEC

RIOTEC OM7222J Manuel utilisateur

RIOTEC

RIOTEC iDC9278K Manuel utilisateur

Manuels Lecteur de codes-barres populaires d'autres marques

POSMicro

POSMicro Datalogic PowerScan D7100 Manuel utilisateur

Marson

Marson MT780 Guide de configuration rapide

NCR

NCR RealPOS Manuel utilisateur

Motorola

Motorola SE3300 Guide de configuration rapide

Element

Element P130BT Manuel utilisateur

Motorola

Motorola Symbol LS3008 Manuel d'installation et d'exploitation

Meec tools

Meec tools OBD-II / VAG Manuel utilisateur

SICK

SICK CLP 100 Manuel utilisateur

Royal Tag SA

Royal Tag SA I-Read Manuel utilisateur

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuel utilisateur

Meteor

Meteor 8310 Manuel utilisateur

Denso

Denso BHT-500B Manuel utilisateur

Datalogic

Datalogic Heron HD3130 Manuel utilisateur

Motorola

Motorola MP6000 Instructions de montage

Newland

Newland NLS-HR15-BT Manuel utilisateur

ARTDEV

ARTDEV AS-1310 Manuel utilisateur

Aopos

Aopos AS290 Manuel utilisateur

ENS

ENS 367-5455 Manuel utilisateur