RIOTEC DC9250DP Manuel utilisateur

1

Quick Guide

-DC9250DP

1 H92P

Connect to micro USB port of OTG device

3



* Before you use scanner, please switch to "C" for battery charge

for 3~4 hours.

* Under “C mode”, you can raise/lower soft-keyboard easily.(For

USB HID only)



H92P Scan Holder is with Li-Ion battery inside. When in charging,

please use the original USB power adaptor of OTG device

(recommended). Through it, it charges both OTG device and H92P

internal battery at the same time. When in low battery (Red LED

flashing), please charge it immediately.

LED Indicator Information

Green LED OFF Full charged (Charge mode)

Green LED ON Charging (Charge mode)

Red LED Flashing Low battery (Operation mode)

Attention: Under “Operation mode” please do not charging,

otherwise the OTG device's battery will be charging back to H92P’s

battery.

5



The touch sensor area is around the central area. (For both sides).

Please check the above drawing for your reference.

Installation

Before using scanner, please make sure that the OTG device is fully

charged.

1. Under USB HID interface

** When plugged into OTG device, it will be recognized and begin

to scan the barcode.

2. Under USB Serial interface

** Please install PL-2303 driver into your OTG device first. PL-2303

driver can be downloaded from Google Play

** Connect scanner to your OTG device, then, you can know which

serial port scanner connects to.

** The data you scan will be sent to serial port and your APP can

get the data from serial port directly.

Suction Cup

Micro USB

cable (OTG)

Li- Ion

Battery

Trigger Area

O = Operation mode

Charge mode

LED Indicator

Char

e por

H92P

Mini

scanner

PU Glue

(Can be used

repeatedly)

2

Reset Configuration to Defaults

If you are unsure of the scanner configuration or have scanned the

incorrect codes, please scan the “Default” barcode. This will reset the

scanner to its factory default. (scan from A1 to A6 for HID or B1 for

USB Serial)

USB HID USB Serial

 Note: Please install PL-2303 driver for USB Serial.

Keyboard Country(For USB HID only)

Scan the appropriate country code as below to program the

keyboard layout for your country or language. As a general

rule, the following characters are supported, but need special

care for countries other than the United States:

@ | $ # { } [ ] = / ‘ \ < > ~

USA

(Original setting)

Italian

Norway

France

Germany

Vietnam

Sweden

Spain

Denmark

ortu

Switzerland Hun

ary

Barcode Configuration Method:

Please follow the below 4 steps to complete the

"Symbologies Enable" or "Symbologies Disable"

1. Start Configuration

2. Choose one of 1D symbologies

3. Enable setting: scan Enable-1, then Enable-2

Disable setting: scan Disable-1, then Disable-2

4. End Configuration

Start

Configuration

1D Symbologies – 1

UPC-A UPC-E

EAN-13

(ISBN/ISSN)

EAN-8

Industrial

2 of 5

Matrix

2 of 5

Enable-1 Disable-1

Enable-2 Disable-2

End

Configuration

3

Barcode Configuration Method:

Please follow the below 4 steps to complete the

"Symbologies Enable" or "Symbologies Disable"

1. Start Configuration

2. Choose one of 1D symbologies

3. Enable setting: scan Enable-1, then Enable-2

Disable setting: scan Disable-1, then Disable-2

4. End Configuration

Start

Configuration

1D Symbologies – 2

Code 93

Code 11

MSI/Plessey

UK/Plessey

Codabar

Code 128

UCC/EAN 128

ISBT 128

1D Symbologies – 3

Code 39

(Code 32)

Interleaved

2 of 5

China Post GS1 DataBar

GS1 DataBar

Limited

GS1 DataBar

Expanded

Enable-1 Disable-1

Enable-2 Disable-2

End

Configuration

 Information in this document is subject to change without notice.

 For more information, please visit:

www.riotec.com.tw

R_180504_01

Autres manuels RIOTEC Lecteur de codes-barres

RIOTEC

RIOTEC LS6300 Manuel utilisateur

RIOTEC

RIOTEC DC9257L Manuel utilisateur

RIOTEC

RIOTEC iDC9600C Manuel utilisateur

RIOTEC

RIOTEC iLS6307LBM Manuel utilisateur

RIOTEC

RIOTEC iDC9508K Manuel utilisateur

RIOTEC

RIOTEC DC9257LP Manuel utilisateur

RIOTEC

RIOTEC iLS6300BQ Manuel utilisateur

RIOTEC

RIOTEC OM7320 Manuel utilisateur

RIOTEC

RIOTEC OM7220J Manuel utilisateur

RIOTEC

RIOTEC iCR6300CBQ Manuel utilisateur

RIOTEC

RIOTEC iDC9270D Manuel utilisateur

RIOTEC

RIOTEC LS6300E Manuel utilisateur

RIOTEC

RIOTEC iLS6302NBQ Manuel utilisateur

RIOTEC

RIOTEC iDC9607L Manuel utilisateur

RIOTEC

RIOTEC DC9250 Manuel utilisateur

RIOTEC

RIOTEC RIOSCAN iLS6300FS Manuel utilisateur

RIOTEC

RIOTEC iDC9500 Manuel utilisateur

RIOTEC

RIOTEC LS6300E Manuel utilisateur

RIOTEC

RIOTEC DC9257A Manuel utilisateur

RIOTEC

RIOTEC iDC9502K Manuel utilisateur

RIOTEC

RIOTEC iDC9272N Manuel utilisateur

RIOTEC

RIOTEC DC9258KP Manuel utilisateur

RIOTEC

RIOTEC iDC9607L Manuel utilisateur

RIOTEC

RIOTEC iLS6303ABQ Manuel utilisateur

Manuels Lecteur de codes-barres populaires d'autres marques

POSMicro

POSMicro Datalogic PowerScan D7100 Manuel utilisateur

Marson

Marson MT780 Guide de configuration rapide

NCR

NCR RealPOS Manuel utilisateur

Motorola

Motorola SE3300 Guide de configuration rapide

Element

Element P130BT Manuel utilisateur

Motorola

Motorola Symbol LS3008 Manuel d'installation et d'exploitation

Meec tools

Meec tools OBD-II / VAG Manuel utilisateur

SICK

SICK CLP 100 Manuel utilisateur

Royal Tag SA

Royal Tag SA I-Read Manuel utilisateur

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuel utilisateur

Meteor

Meteor 8310 Manuel utilisateur

Denso

Denso BHT-500B Manuel utilisateur

Datalogic

Datalogic Heron HD3130 Manuel utilisateur

Motorola

Motorola MP6000 Instructions de montage

Newland

Newland NLS-HR15-BT Manuel utilisateur

ARTDEV

ARTDEV AS-1310 Manuel utilisateur

Aopos

Aopos AS290 Manuel utilisateur

ENS

ENS 367-5455 Manuel utilisateur