RIOTEC ILS6300DBU Manuel utilisateur

P r o g r a mm i ng Q u i c k G u i d e

-iLS6300DBU/iLS6300DB

Connecting the Scanner

Be sure that PC is turned OFF, before Connect scanner cable to

the PC USB port on the PC as below described, Ensure that all

connections are ready, and turn on your PC.

1. Please switch ON and charge scanner for 4~5 hours at first time

before use. Scanner switch shown on Fig. 2.

2. After switch ON, the Orange LED will flash following with 3

beep-sounds. The RED LED will be OFF while it links to cradle

within Bluetooth radio range.

3. If RED LED is continual ON, please re-plug USB cable, then, scan

the 3 barcodes on the bottom of cradle sequentially. (Shown on

Fig. 3 From 1 to 3).

4. Charging issue: Cradle works as charger when putting scanner on

it. Even if the scanner's battery is full, the cradle will continue to

supply power to the scanner. We suggest you to remove scanner

from cradle when scanner is charged fully

*Note: Please install PL-2303 driver for iLS6300DB

LED Indicator Information

Orange LED ON

Full charged

Orange LED Flashing

Charging / Low battery

Red LED ON

Not read

Red LED Continual ON

Off line / out of service

Green LED ON

Good read

Remark:

*When the battery power is too low, the Orange LED will flash and beep

once. Scanner should be charged immediately.

*If scanner shuts down it is recommended to charge it fully before

turning it back on.

*Under power-saving mode, there will not be LED indication when charging.

Reset Configuration to Defaults

(scan from A1 to A7 for iLS6300DBU or B1 to B2 iLS6300DB)

iLS6300DBU

iLS6300DB

%%RSDF

%SETUP

Demo

%D%F%T

8002

%%%END

Demo

%D%F%T

*Note: Please install PL-2303 driver for iLS6300DB

Trigger Mode

Demo

%R%T%E

Trigger always

(Trigger available at any time)

Demo

%R%T%D

Trigger standard (Default)

(Trigger available, after data sent to the

device)

Transmission Speed

Transmission speed is dependent on your device. In order not to lose

data, please choose the correct speed. Middle-speed is the Default.

Demo

%B%T%H

Demo

High-speed

Ultra Slow-speed

Transmission

1transmission

Demo

Middle-speed

Ultra Slow-speed

Transmission

(Default)

2transmission

Demo

%B%T%L

Demo

Slow-speed

Ultra Slow-speed

Transmission

3transmission

Bluetooth Auto-connection

Demo

%A%L%E

Bluetooth Auto-connection ON:

When out of range, it will keep trying to

connect to device, scanner will not enter

power-saving mode.

Demo

%A%L%D

Bluetooth Auto-connection OFF:

When you are out of BT signal range, scanner

will stop sending auto-connection signal to

device after 2 minutes. During this time, it will

not enter power-saving mode.

Once you are back within range, press trigger to

connect to the device. (Default)

Keyboard Country(For USB HID only)

Scan the appropriate country code as below to program the keyboard

layout for your country or language. As a general rule, the following

characters are supported, but need special care for countries other

than the United States: @ | $ # { } [ ] = / ‘ \ < > ~

%+-$.00

%+-$.06

USA

(Original setting)

Italian

%+-$.01

%+-$.07

Norway

France

%+-$.02

%+-$.08

Germany

Vietnam

%+-$.03

%+-$.09

Sweden

Spain

%+-$.04

%+-$.10

Denmark

Portugal

%+-$.05

%+-$.11

Switzerland (F)

Hungary

%+-$.12

%+-$.18

Latin America

Icelandic

%+-$.13

%+-$.19

Brazil

Poland

%+-$.14

%+-$.20

Belgium

Turkey F

%+-$.15

%+-$.21

Bulgarian Latin

Turkey Q

%+-$.16

%+-$.22

Finland

Japan

%+-$.17

%+-$.23

Netherlands

Korea

%+-$.24

%+-$.26

Thai

Russia

%+-$.25

Switzerland German

*The different keyboard language option starts from June. 2017.

Power-saving Mode

Demo

%P%D%T00

Power-saving mode OFF

Demo

%P%D%T03

Power-saving mode ON (Default):

Enter power-saving mode after 3-minute inactivity.

This function converses battery power. When you

press "SCAN/Power ON" button, it will wake up and

begin to scan.

Demo

%P%D%T10

Power-saving mode ON:

Enter power-saving mode after 10-minute

inactivity. This function converses battery power.

When you press "SCAN/Power ON" button, it will

wake up and begin to scan.

*When charging, the scanner will not enter power-saving mode

automatically

How to append a “prefix” or a “suffix” to the

barcode data

Demo

%C%P%S

Demo

%C%S%S

prefix

suffix

1. Scan above configuration code for Prefix or Suffix

2. Enter the required values (right, numeric barcode) for Prefix or

Suffix using the hex values for the desired HEX values from “Prefix

& Suffix TABLE (blew page)”

3. Then, end by scanning Code X (below, right)

*The max. of special characters is 5.

*When you append 1~4 required values for Prefix or Suffix, it must

end with Code X

*It doesn’t need Code X, if you append 5 values to barcode data.

How to delete Prefix or Suffix

1. Scan above configuration code for Prefix or Suffix

2. Enter the “0” “0” (above, right)

3. Then end by scanning Code X (below, right)

Numeric barcode for settings

Demo

www.tec-it.com

Demo

Prefix & Suffix TABLE

HEX

HID

(SPP)

HEX

HID

(SPP)

HEX

CTRL A

(SOH)

CTRL Y

(EM)

SPACE

CTRL B

(STX)

CTRL

Z(SUB)

CTRL C

(ETX)

ESC

(ESC)

CTRL D

(EOT)

CTRL \

(FS)

;

CTRL E

(ENQ)

CTRL ]

(GS)

CTRL F

(ACK)

CTRL ^

(RS)

CTRL G

(BEL)

CTRL _

(US)

Backspace

(BS)

Tab

(HT)

(

CTRL J

(LF)

)

CTRL K

(VT)

CTRL L

(FF)

[

Enter

(CR)

CTRL N

(SO)

]

CTRL O

(SI)

CTRL P

(DLE)

CTRL Q

(DC1)

CTRL R

(DC2)

CTRL S

(DC3)

CTRL T

(DC4)

{

CTRL U

(NAK)

CTRL V

(SYN)

}

CTRL W

(ETB)

CTRL X

(CAN)

Barcode Configuration Method:

Please follow the below 1~5 steps to complete the

“Symbologies enable” or “Symbologies disable”

1. Start Configuration 2. Choose one Symbologies

3 & 4 scan 2 Enable (or Disable) setting codes

5. End Configuration

Start

Configuration

%SETUP

1D Symbologies –1

UPC-A

UPC-E

1101

1201

EAN-13

(ISBN/ISSN)

EAN-8

1301

1401

Industrial

2 of 5

Matrix

2 of 5

1701

1801

Code 93

Code 11

2101

2201

MSI/Plessey

UK/Plessey

2301

2401

1D Symbologies –2

Codabar

ISBT 128

1901

3301

UCC/EAN 128

Interleaved

2 of 5

2501

1601

Code 39

(Code 32)

GS1 DataBar

1501

2701

China Post

GS1 DataBar

Expanded

2601

2901

GS1 DataBar

Limited

2801

Enable

Disable

Enable

Disable

End

Configuration

%%%END

Quick guide is subject to change without notice.

R_180808_01

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels RIOTEC Lecteur de codes-barres

RIOTEC

RIOTEC iLS6302NBU Manuel utilisateur

RIOTEC

RIOTEC CR6307A Manuel utilisateur

RIOTEC

RIOTEC iDC9508K Manuel utilisateur

RIOTEC

RIOTEC DC9277L Manuel utilisateur

RIOTEC

RIOTEC iLS6307LBM Manuel utilisateur

RIOTEC

RIOTEC RIOSCAN Manuel utilisateur

RIOTEC

RIOTEC iDC9607LW Manuel utilisateur

RIOTEC

RIOTEC RIOSCAN iLS6300FS Manuel utilisateur

RIOTEC

RIOTEC LS6322A Manuel utilisateur

RIOTEC

RIOTEC FS5100D Manuel utilisateur

RIOTEC

RIOTEC iLS6300VBU Manuel utilisateur

RIOTEC

RIOTEC LS6300V Manuel utilisateur

RIOTEC

RIOTEC LS6300E Manuel utilisateur

RIOTEC

RIOTEC OM7228J Manuel utilisateur

RIOTEC

RIOTEC FS5020E Manuel utilisateur

RIOTEC

RIOTEC iDC9608K Manuel utilisateur

RIOTEC

RIOTEC iDC9272A Manuel utilisateur

RIOTEC

RIOTEC iLS6303XBQ Manuel utilisateur

RIOTEC

RIOTEC RIOSCAN iLS6307LS Manuel utilisateur

RIOTEC

RIOTEC iLS6302J/KBU Manuel utilisateur

RIOTEC

RIOTEC LS6300F Manuel utilisateur

RIOTEC

RIOTEC iLS6308KBQ Manuel utilisateur

RIOTEC

RIOTEC iDC9273A Manuel utilisateur

RIOTEC

RIOTEC iDC9600KW Manuel utilisateur

Manuels Lecteur de codes-barres populaires d'autres marques

POSMicro

POSMicro Datalogic PowerScan D7100 Manuel utilisateur

Marson

Marson MT780 Guide de configuration rapide

NCR

NCR RealPOS Manuel utilisateur

Motorola

Motorola SE3300 Guide de configuration rapide

Element

Element P130BT Manuel utilisateur

Motorola

Motorola Symbol LS3008 Manuel d'installation et d'exploitation

Meec tools

Meec tools OBD-II / VAG Manuel utilisateur

SICK

SICK CLP 100 Manuel utilisateur

Royal Tag SA

Royal Tag SA I-Read Manuel utilisateur

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuel utilisateur

Meteor

Meteor 8310 Manuel utilisateur

Denso

Denso BHT-500B Manuel utilisateur

Datalogic

Datalogic Heron HD3130 Manuel utilisateur

Motorola

Motorola MP6000 Instructions de montage

Newland

Newland NLS-HR15-BT Manuel utilisateur

ARTDEV

ARTDEV AS-1310 Manuel utilisateur

Aopos

Aopos AS290 Manuel utilisateur

ENS

ENS 367-5455 Manuel utilisateur

RIOTEC iLS6300DBU Manuel utilisateur

Manuels Lecteur de codes-barres populaires d'autres marques