RIOTEC ILS6300FBQ Manuel utilisateur

Programming Quick Guide

-iLS6300FBQ/iLS6300FBM

Connecting the Scanner

Be sure that PC is turned OFF, before Connect scanner cable to

the PC USB port on the PC as below described, Ensure that all

connections are ready, and turn on your PC.

1. Please switch ON and charge scanner for 4~5 hours at first time

before use. Scanner switch shown on Fig. 2.

2. After switch ON, the Orange LED will flash following with 3

beep-sounds. The RED LED will be OFF while it links to cradle

within 2.4GHz radio range.

3. If RED LED is continual ON, please re-plug USB cable, then, scan

the 3 barcodes on the bottom of cradle sequentially. (Shown on

Fig. 3 From 1 to 3).

4. Charging issue: Cradle works as charger when putting scanner on

it. Even if the scanner's battery is full, the cradle will continue to

supply power to the scanner. We suggest you to remove scanner

from cradle when scanner is charged fully

*Note: Please install PL-2303 driver for iLS6300FBM

LED Indicator Information

Orange LED ON

Full charged

Orange LED Flashing

Charging / Low battery

Red LED ON

Not read

Red LED Continual ON

Off line / out of service

Green LED ON

Good read

Orange LED ON

Good read (Batch mode)

Remark:

*When the battery power is too low, the Orange LED will flash and beep

once. Scanner should be charged immediately.

*If scanner shuts down it is recommended to charge it fully before

turning it back on.

*Under power-saving mode, there will not be LED indication when charging.

Reset Configuration to Defaults

(scan from A1 to A5 for iLS6300DBQ or B1 to B6 iLS6300DBM)

iLS6300FBQ

iLS6300FBM

*Note: Please install PL-2303 driver for iLS6300FBM

There are two operating modes on the scanner

1.Data Transmission mode (Default)

It is a necessary to scan “clean memory data" when

switching between these two modes.

Within 2.4GHz radio range

Beyond 2.4GHz radio range

Data

read Transmit data to PC/terminal

directly

Save data into scanner’s memory,

scanner will transmit data to PC/

terminal automatically when back to

2.4GHz radio range.

Enter Data Storage mode

LED

Green/ Orange LED flashes

followed by 3 beeps.

2.Data Storage mode (Batch Mode)

It is a necessary to scan “clean memory data" when switching

between these two modes.

Data

read

Save data directly to scanner’s memory, It will transmit the data to PC/

terminal after you scan the Transmit memory data code. To delete

data please scan the Clean memory data code.

Enter Data Transmission mode

LED

Green/Orange LED flashes followed by 3 beeps.

Always Clean memory data before switching to Data Transmission

Mode.

Otherwise Red/ Orange LED will flash with one long beep and will not

switch modes.

Under Data storage Mode

The data can be keep or delete by option after transmit

Keep the data

(Default)

Delete the data

Transmit memory data

Green/Orange LED Flashes followed by 3 beeps

Clean memory data

Green/Orange LED flashes followed by 3 beeps

The barcode data which is stored in the memory will be deleted.

Trigger Mode

Trigger always

(Trigger available at any time)

Trigger standard (Default)

(Trigger available, after data sent to the

device)

Transmission Speed

Transmission speed is dependent on your device. In order not to lose

data, please choose the correct speed. Middle-speed is the Default.

High-speed

Ultra Slow-speed

Transmission

1transmission

Middle-speed

Ultra Slow-speed

Transmission

(Default)

2transmission

Slow-speed

Ultra Slow-speed

Transmission

3transmission

Wireless Auto-connection

Wireless Auto-connection ON:

When out of range, it will keep trying to

connect to device, scanner will not enter

power-saving mode.

Wireless Auto-connection OFF:

When you are out of BT signal range, scanner

will stop sending auto-connection signal to

device after 2 minutes. During this time, it will

not enter power-saving mode.

Once you are back within range, press trigger to

connect to the device. (Default)

Power-saving Mode

Power-saving mode OFF

Power-saving mode ON (Default):

Enter power-saving mode after 3-minute

inactivity. This function converses battery

power. When you press "SCAN/Power ON"

button, it will wake up and begin to scan.

Power-saving mode ON:

Enter power-saving mode after 10-minute

inactivity. This function converses battery

power. When you press "SCAN/Power ON"

button, it will wake up and begin to scan.

*When charging, the scanner will not enter power-saving mode

automatically.

Keyboard Country(For USB HID only)

Scan the appropriate country code as below to program the keyboard

layout for your country or language. As a general rule, the following

characters are supported, but need special care for countries other

than the United States: @ | $ # { } [ ] = / ‘ \ < > ~

USA

(Original setting)

Italian

Norway

France

Germany

Vietnam

Sweden

Spain

Denmark

Portugal

Switzerland

Hungary

How to append a “prefix” or a “suffix”

to the barcode data

prefix

suffix

1. Scan above configuration code for Prefix or Suffix

2. Enter the required values (right, numeric barcode) for Prefix or Suffix

using the hex values for the desired HEX values from “Prefix & Suffix

TABLE (blew page)”

3. Then, end by scanning Code X (below, right)

*The max. of special characters is 5.

*When you append 1~4 required values for Prefix or Suffix, it must end

with Code X

*It doesn’t need Code X, if you append 5 values to barcode data.

How to delete Prefix or Suffix

1. Scan above configuration code for Prefix or Suffix

2. Enter the “0” “0” (above, right)

3. Then end by scanning Code X (below, right)

Numeric barcode for settings

Prefix & Suffix TABLE

HEX

HID

(SPP)

HEX

HID

(SPP)

HEX

CTRL A

(SOH)

CTRL Y

(EM)

20 SPACE 38 8 50 P 68 h

CTRL B

(STX)

CTRL

Z(SUB)

21 ! 39 9 51 Q 69 i

CTRL C

(ETX)

ESC

(ESC)

22 " 3A : 52 R 6A j

CTRL D

(EOT)

CTRL \

(FS)

23 # 3B ; 53 S 6B k

CTRL E

(ENQ)

CTRL ]

(GS)

24 $ 3C < 54 T 6C l

CTRL F

(ACK)

CTRL ^

(RS)

25 % 3D

= 55 U 6D m

CTRL G

(BEL)

CTRL _

(US)

26 & 3E > 56 V 6E n

Backspace

(BS)

27 ' 3F ? 57 W 6F o

Tab

(HT)

28 ( 40 @ 58 X 70 p

CTRL J

(LF)

29 ) 41 A 59 Y 71 q

CTRL K

(VT)

2A * 42 B 5A Z 72 r

CTRL L

(FF)

2B + 43 C 5B [ 73 s

Enter

(CR)

2C , 44 D 5C \ 74 t

CTRL N

(SO)

2D - 45 E 5D ] 75 u

CTRL O

(SI)

2E . 46 F 5E ^ 76 v

CTRL P

(DLE)

2F / 47 G 5F _ 77 w

CTRL Q

(DC1)

30 0 48 H 60 ` 78 x

CTRL R

(DC2)

31 1 49 I 61 a 79 y

CTRL S

(DC3)

32 2 4A J 62 b 7A z

CTRL T

(DC4)

33 3 4B K 63 c 7B {

CTRL U

(NAK)

34 4 4C L 64 d 7C |

CTRL V

(SYN)

35 5 4D

M 65 e 7D }

CTRL W

(ETB)

36 6 4E N 66 f 7E ~

CTRL X

(CAN)

37 7 4F O 67 g

Barcode Configuration Method:

(Flow chart for setup procedure :)

Start

Configuration

End

Configuration

1D Symbologies – 1

ENABLE

UPC-E

DISABLE

ENABLE

UPC-A

EAN13

DISABLE

ENABLE

EAN8

DISABLE

ENABLE

CODE 39

DISABLE

Barcode Configuration Method:

(Flow chart for setup procedure :)

Start

Configuration

End

Configuration

1D Symbologies – 2

ENABLE

CODE 93

DISABLE

ENABLE

CODE 11

DISABLE

ENABLE

CODE 128

EAN/UCC 128

DISABLE

1D Symbologies – 3

ENABLE

INTERLEAVED 25

DISABLE

ENABLE

STANDARD 25

INDUSTRIAL 25

DISABLE

ENABLE

MATRIX 25

DISABLE

ENABLE

CHINESE POST

DISABLE

ENABLE

CODABAR

DISABLE

Quick guide is subject to change without notice.

R_160303_01

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels RIOTEC Lecteur de codes-barres

RIOTEC

RIOTEC FS5100D Manuel utilisateur

RIOTEC

RIOTEC iLS6303ABQ Manuel utilisateur

RIOTEC

RIOTEC OM7220J Manuel utilisateur

RIOTEC

RIOTEC iLS6307LB Manuel utilisateur

RIOTEC

RIOTEC iLS6308KBU Manuel utilisateur

RIOTEC

RIOTEC iLS6308KBQ Manuel utilisateur

RIOTEC

RIOTEC iLS6302J BQ Manuel utilisateur

RIOTEC

RIOTEC OM7228J Manuel utilisateur

RIOTEC

RIOTEC iDC9600C Manuel utilisateur

RIOTEC

RIOTEC iDC9277L Manuel utilisateur

RIOTEC

RIOTEC LS6300E Manuel utilisateur

RIOTEC

RIOTEC iCR6300CBQ Manuel utilisateur

RIOTEC

RIOTEC RIOSCAN iLS6300FS Manuel utilisateur

RIOTEC

RIOTEC LS6307 USB Manuel utilisateur

RIOTEC

RIOTEC OM7320 Manuel utilisateur

RIOTEC

RIOTEC DC9253AP Manuel utilisateur

RIOTEC

RIOTEC RIOSCAN iCR6307AS Manuel utilisateur

RIOTEC

RIOTEC iDC9600KW Manuel utilisateur

RIOTEC

RIOTEC iLS6302NBQ Manuel utilisateur

RIOTEC

RIOTEC DC9257LP Manuel utilisateur

RIOTEC

RIOTEC iLS6300DBQ Manuel utilisateur

RIOTEC

RIOTEC iDC9607AW Manuel utilisateur

RIOTEC

RIOTEC CR6327A Manuel utilisateur

RIOTEC

RIOTEC iDC9500 Manuel utilisateur

Manuels Lecteur de codes-barres populaires d'autres marques

POSMicro

POSMicro Datalogic PowerScan D7100 Manuel utilisateur

Marson

Marson MT780 Guide de configuration rapide

NCR

NCR RealPOS Manuel utilisateur

Motorola

Motorola SE3300 Guide de configuration rapide

Element

Element P130BT Manuel utilisateur

Motorola

Motorola Symbol LS3008 Manuel d'installation et d'exploitation

Meec tools

Meec tools OBD-II / VAG Manuel utilisateur

SICK

SICK CLP 100 Manuel utilisateur

Royal Tag SA

Royal Tag SA I-Read Manuel utilisateur

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuel utilisateur

Meteor

Meteor 8310 Manuel utilisateur

Denso

Denso BHT-500B Manuel utilisateur

Datalogic

Datalogic Heron HD3130 Manuel utilisateur

Motorola

Motorola MP6000 Instructions de montage

Newland

Newland NLS-HR15-BT Manuel utilisateur

ARTDEV

ARTDEV AS-1310 Manuel utilisateur

Aopos

Aopos AS290 Manuel utilisateur

ENS

ENS 367-5455 Manuel utilisateur

RIOTEC iLS6300FBQ Manuel utilisateur

Manuels Lecteur de codes-barres populaires d'autres marques