Renesas RC32012A Manuel utilisateur
Evaluation Kit Manual
R31UH0010EU0102 Rev.1.02 Page 1
Apr 20, 2022 © 2021-2022 Renesas Electronics
The RC32012A evaluation board allows customers to
evaluate Renesas ClockMatrix devices (e.g.,
RC32012A, QFN-72). This document discusses the
following:
▪ The board’s design, its power supply, and jumper
settings
▪ The input and output connectors for normal
operation
▪ How to bring up the board using the Timing
Commander software GUI
▪ How to configure and program the board to
generate standard-compliant frequencies
Kit Contents
The RC32012A EVK ships with the following:
▪ RC32012A Evaluation Board
▪ USB Type-A cable
PC Requirements
▪ Renesas Timing Commander Software installed
▪ ClockMatrix GUI
▪ USB 2.0 or USB 3.0 interface
▪ Windows XP SP3, or later
▪ Processor: Minimum 1GHz
▪ Memory: Minimum 512MB; recommended 1GB
▪ Available Disk Space: Minimum 600MB (1.5GB,
64-bit); recommended 1GB (2GB, 64-bit)
▪ Network access during installation if the .NET
framework is not currently installed on the system
Figure 1. RC32012A Evaluation Board
RC32012A
Evaluation Kit
R31UH0010EU0102 Rev.1.02 Page 2
Apr 20, 2022
RC32012A Evaluation Kit Manual
Contents
1. Board Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 Board Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.2 Voltage Selection Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.3 GPIO Switches, LEDs, and Test Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.4 USB Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.5 I2C between FTDI, ClockMatrix Device, and On-board EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2. Working with Timing Commander for Programing/Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1 Default Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2 Using Timing Commander to Control the Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.3 Output Terminations and Rework to Take 1PPS Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3. Schematic Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Appendix A. How to Upgrade the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4. Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5. Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
R31UH0010EU0102 Rev.1.02 Page 3
Apr 20, 2022
RC32012A Evaluation Kit Manual
1. Board Design
The following diagram identifies the various components of the evaluation board: input and output SMA
connectors, power supply jacks, and some jumper settings necessary for the board operations. Detailed
descriptions are included below.
Figure 2. RC32012A Evaluation Board – Detailed
▪Input SMA connectors – There are five differential inputs labeled CLK0/nCLK0 - CLK4/nCLK4. Each input
clock can be configured differentially (LVDS, PECL 2.5V, and PECL 3.3V) or in single-ended format (CMOS).
▪Output SMA connectors – There are 12 outputs labeled as Q0/nQ0 - Q11/nQ11. Each output clock can be
configured differentially (LVDS, LVPECL, or user-defined amplitude) or in single-ended format (LVCMOS – in-
phase or out-of-phase).
▪GPIO switch, LEDs, and Test points – There are seven GPIOs available. Each GPIO can be set a “low” or
“high” level (if input) or displayed with an LED (if output). Some GPIOs are used to set the chip in a certain
working condition on power-up. For more information, see “Table 18. GPIO Pin Usage at Start-Up” in the
RC32012A Datasheet.
▪USB connector – A USB mini connector connects the evaluation board to a PC for GUI communications. No
power is consumed from the USB connector other than to power the FTDI USB device.
▪VDDQx voltage selection jumpers – Each output voltage can be individually supplied with 1.8V, 2.5V, or 3.3V.
These jumpers are used to select the voltage for the output voltages.
▪Reset button: A small button is used to reset the board.
▪OSCI Input connector – An SMA connector, J45, is provided to optionally supply a clock signal to overdrive
the crystal.
▪OCXO/TCXO Reference (Optional) – An OCXO/TCXO footprint, output at J82. It can be connected to J46
(below) as the reference for System DPLL.
R31UH0010EU0102 Rev.1.02 Page 4
Apr 20, 2022
RC32012A Evaluation Kit Manual
▪SysDPLL Input (Optional) – An SMA connector, J46, is provided to supply a local OCXO/TCXO reference as
an optional reference for System DPLL.
▪Crystal: A crystal of various frequencies must be present for board operations. A 3225 footprint is provided for
SMT crystals. For easy plug-in of a canned crystal, two through-holes are also available.
▪EEPROM – An SO-8 socket is provided to hold an EEPROM device of compatible package. EEROM is used to
store firmware and customer configuration data, if needed.
1.1 Board Power Supply
The evaluation board uses a single +5V supply for its power supplies. When running the board, please set the
bench power supply at 5V/2A. The red jack (J1) is positive; the black jack (J2) is the ground.
Multiple LDOs are used to generate 3.3V, 2.5V, and 1.8V from the +5V supply.
1.2 Voltage Selection Jumpers
There are eight headers/jumpers for selecting different voltages for different functional blocks of the device. Each
header has Pin 1 and 3 labeled in silkscreen – jumping pin 1 and pin 2 will select 3.3V; jumping pin 2 and pin 3 will
select 2.5V. No jumper will have 1.8V.
Please see the following example for JP4 and JP9 – JP4 will select 2.5V, JP9 will select 3.3V.
Figure 3. Example of Voltage Jumpers
The following list shows which head/jumper is used to select a specific voltage:
▪ JP1 – VDDD
▪ JP2 – VDDA
▪ JP3 – VCC_GPIO_DC
▪ JP4 – VDDO_Q8_3_5
▪ JP5 – VDDO_Q2_4_11
▪ JP6 – VDDO_1_10_7
▪ JP7 – VDD_CLK0
▪ JP9 – VDDO_Q0_9_6
R31UH0010EU0102 Rev.1.02 Page 5
Apr 20, 2022
RC32012A Evaluation Kit Manual
Note: VDD_FOD voltage is selected by resistor R908 and R909. In order to prevent damage to the device, both
R908 and R909 should not be stuffed, in which case VDD_FOD = 1.8V.
1.3 GPIO Switches, LEDs, and Test Points
An 8-bit, 3-position dip switch is used to set the logic levels for seven GPIOs (GPIO0-5, GPIO9). The GPIO levels
for each setting and the corresponding LED state are listed in the following table (see picture and labels in
Figure 4).
When the GPIOs are configured as outputs (such as User-Controlled or LOL indicator), the dip switch for the
corresponding GPIO should be placed in the Center position. The LED will indicate the state of the GPIO.
Figure 4. GPIO Setting and Status Display Area
1.4 USB Jack
This is a USB mini connector to the board. The other end of the USB cable is a USB Type A connector going to a
PC.
Table 1. GPIO Settings
Dip Switch Position GPIO Logic Level LED
Left Low On
Center High if GPIO is configured as Input
High or Low according to the GPIO output setting
High if GPIO is configured as Input
High or Low according to the GPIO output setting
Right High Off
R31UH0010EU0102 Rev.1.02 Page 6
Apr 20, 2022
RC32012A Evaluation Kit Manual
1.5 I2C between FTDI, ClockMatrix Device, and On-board EEPROM
One of the major differences between the QFN-72 ClockMatrix device and its BGA-144 counterpart is that there is
only one serial bus on the QFN-72 device. The I2C bus between the FTDI chip and ClockMatrix device is the
same bus between the ClockMatrix device and the on-board EEPROM. The on-board EEPROM is used to store
device firmware and/or customer’s configuration data. JP12 and JP13 must be jumped between Pin 1 and 2 to
enable the I2C connections.
2. Working with Timing Commander for Programing/Configuration
The following sections are best cross-referenced with the ClockMatrix GUI Step-by-Step User Guide that is
available on the ClockMatrix Timing Solutions page and various ClockMatrix device product pages.
2.1 Default Operation
The evaluation board can be operated off EEPROM, which has stored all information including firmware and a
default configuration data. A default operation provides a sanity check on the board before running the board
through the Timing Commander tool. Please set the board to the following default conditions (for jumper and
switch positions, see Figure 5):
▪ Set all the GPIOs to the Center position. This will ensure that GPIO9 is high and that the serial port is
configured for I2C 1-byte addressing.
▪ VDDA = 3.3V, VDD_GPIO_FOD = 1.8V, VDD0_Qx = 3.3V
▪ Crystal frequency 50MHz
▪ CLK0 = 25MHz
▪ FTDI, ClockMatrix device, and EEPROM share the same I2C bus by jumping Pin 1 and 2 of JP12 and JP13
With the above default conditions ready, connect the evaluation board to the PC using a USB cable (type A on the
PC side and mini-type on the board side), and power up the board using a single +5V supply. On power-up, the
ClockMatrix device will read its firmware and configuration data from EEPROM and update all the registers. When
this process completes, the following frequencies are available:
▪ Q0 = 122.88MHz
▪ Q1 = 122.88MHz
Table 2. EEPROM I2C Connections
JP12/JP13 JP12/JP13
Jumper position Pin 1 and 2 Pin 2 and 3
I2C Path FDTI and CM chip;
CM chip and EEPROM
N/A
R31UH0010EU0102 Rev.1.02 Page 7
Apr 20, 2022
RC32012A Evaluation Kit Manual
Figure 5. Board Setting for Default Operation
Note: In order to set GPIO9 to “High”, the switch for GPIO9 must be set either to the “+” (high) position or the
center position.
Before proceeding to communicate to the ClockMatrix device using the Timing Commander GUI, two I2C
connection methods are introduced:
1. Using the on-board FTDI circuit – The evaluation board has on-board FTDI circuitry to translate Timing
Commander access activities from USB to the I2C port of the ClockMatrix device. This is to connect the PC to
the board through the Type-B connector.
2. Using FTDI dongle (C232HM-DDHSL-0 cable) – The dongle has the same FTDI circuit as this board built in it
(see Figure 6). The benefit of using this dongle is to connect to the customer’s board and still enjoy the
debugging capabilities that Timing Commander has to offer.
R31UH0010EU0102 Rev.1.02 Page 8
Apr 20, 2022
RC32012A Evaluation Kit Manual
Figure 6. FTDI Dongle: USB Type-A at PC end and 10 Free-wires at the other end
The free wires are color-coded and numerically indexed as displayed in the following picture.
When using with Timing Commander, only four wires are used. When connecting to a customer board, connect
the Orange wire to SCL; tie the Yellow wire and Green wire together and connect to SDA; then, importantly,
connect the Black ground wire to the customer’s board GND. Assuming there is a pull-up resistor for SCL and
SDA, respectively, on customer board.
By using FTDI dongle, we can connect to a customer board and use the Timing Commander GUI just like working
on a ClockMatrix evaluation board. When using the FTDI dongle to connect to a customer board, in Timing
Commander “Connection Settings” window, “On-board USB (SPI)” is selected in Connection Interface box (see
Figure 10), same as connecting to a Renesas evaluation board.
Color Pin Number Name Type Description
Orange 2 SCL Output Serial Clock
Yellow 3 SDA Input/Output Serial data signal shorted together to
create bidirectional data (both yellow
and green wires must be shorted
together)
Green 4
R31UH0010EU0102 Rev.1.02 Page 9
Apr 20, 2022
RC32012A Evaluation Kit Manual
2.2 Using Timing Commander to Control the Board
Once the default operation is successful, complete the following steps using Timing Commander to configure and
program the ClockMatrix device as per your application requirements.
1. Power up the board and set the main serial port in I2C mode by GPIO9 = “high”. See Figure 5 for the GPIO9
position. Connect the board to PC.
2. Start the Timing Commander software.
You will see options of “New Setting File” and “Open Setting file”. For a new configuration, select “New Setting
File”
Figure 7. Starting Up Timing Commander GUI
R31UH0010EU0102 Rev.1.02 Page 10
Apr 20, 2022
RC32012A Evaluation Kit Manual
3. After selecting “New Settings File”, a device selection window will appear. In the window, choose the intended
device in the list (RC32012A is selected in this example).
Click the button at the lower right corner of the window (red circle) to browse and select the correct personality
file (in this example, personality Version 10.0.1 is selected), then click OK.
Figure 8. Selecting RC32012A using Personality File Version 10.0.1
Table des matières
Autres manuels Renesas Matériel informatique
Renesas
Renesas RX13T Manuel utilisateur
Renesas
Renesas PCA7757 Manuel utilisateur
Renesas
Renesas V850ES/JJ3 Manuel utilisateur
Renesas
Renesas M3T-FLX-DCT613 Manuel utilisateur
Renesas
Renesas DA14AVDDECTDEVKT Manuel utilisateur
Renesas
Renesas GreenPAK SLG47115V Manuel utilisateur
Renesas
Renesas H8/36014 Manuel utilisateur
Renesas
Renesas H8S/2237 Series Manuel utilisateur
Renesas
Renesas HSG2004 Manuel utilisateur
Renesas
Renesas 38K0 Manuel utilisateur
Renesas
Renesas SDI Emulator System M32100T-EZ-E Manuel utilisateur
Renesas
Renesas RSKH8S2215R Manuel utilisateur
Renesas
Renesas QB-RL78D1A2 Manuel utilisateur
Renesas
Renesas Emulator MCU Board M37549T-RLSS Manuel utilisateur
Renesas
Renesas R0E510Y16LVB00 Manuel utilisateur
Renesas
Renesas Single-Chip Microcomputer M34551T2-MCU Manuel utilisateur
Renesas
Renesas H8S/2338 Series Manuel utilisateur
Renesas
Renesas Emulator System E8 Manuel utilisateur
Renesas
Renesas M302N1 Manuel utilisateur
Renesas
Renesas H8S/2345 Series Manuel utilisateur
Manuels Matériel informatique populaires d'autres marques
EMC2
EMC2 VNX Series Manuel du propriétaire
Panasonic
Panasonic DV0PM20105 Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuel utilisateur
Raidon
Raidon iT2300 Manuel utilisateur
National Instruments
National Instruments PXI-8186 Manuel utilisateur
