Raven AccuBoom Manuel utilisateur

TerraGator with Liquid Bed

AccuBoom™ Installation Manual

P/N 016-0171-062 Rev A 09/15

While every effort has been made to ensure the accuracy of this document,

Raven Industries assumes no responsibility for omissions and errors. Nor is any

liability assumed for damages resulting from the use of information contained

herein.

Raven Industries shall not be held responsible or liable for the effects of

atmospheric conditions and sunspot activity on the performance of our products.

Raven Industries cannot guarantee the accuracy, integrity, continuity, or

availability of the GPS signal from the U.S. Department of Defense/NAVSTAR

GPS satellites, the OmniSTAR correction service, or the WAAS correction

service. Raven Industries accepts no responsibility for the use of the signal for

other than the stated purpose.

Raven Industries shall not be responsible or liable for incidental or consequential

damages or a loss of anticipated benefits or profits, work stoppage or loss, or

impairment of data arising out of the use, or inability to use, this system or any of

its components.

Disclaimer

SECTION 1

INTRODUCTION

Congratulations on your purchase of the Raven AccuBoom system! This system is

designed to provide worry free turn on and turn off of your booms with respect to the as-

applied coverage map. The following instructions are designed to assist you in the proper

installation of the AccuBoom system. See the Viper Installation and Operation Manual

for instructions on setting up the software and using the AccuBoom system. You will also

need a valid AccuBoom Control activation key for your Viper in order to activate the

AccuBoom system.

IMPORTANT: All boom switches must remain in the ON

position while AccuBoom control is in operation!

COMPONENTS NEEDED

Terragator with Liquid Bed Kit P/N 9-117-0171-079 including:

CAN AccuBoom Control Node – P/N 063-0172-316

AccuBoom Software Activation Key – P/N 077-0180-010

Terragator With Liquid Bed AccuBoom Cable – P/N 115-0171-701

CAN Tee Cable 12 foot – P/N 115-0171-362

AccuBoom Installation Sheet, Terragator With Liquid Bed – 016-0171-062

P/N 016-0171-062 Page2 of 7

SECTION 2

INSTALLATION

Use the following procedure to properly install the CAN AccuBoom system on a

Terragator With Liquid Bed:

1. Connect AccuBoom cable to AccuBoom node.

a. Connect the rectangular connectors from the AccuBoom Cable P/N 115-

0171-701 to the CAN Accuboom Node P/N 063-0172-316.

2. Mount the CAN AccuBoom node behind the Air Box.

a. Locate the Terragator boom cable connectors located on the right side of

the Air Box. These connectors are 12 pin Deutsch connectors.

P/N 016-0171-062 Page3 of 7

b. Mount the Raven CAN AccuBoom Node P/N 063-0172-316 within 5 feet

of the air box connectors.

3. Connect AccuBoom cable to the sprayer boom harness.

a. Unplug the Terragator boom cable from the Air Box.

P/N 016-0171-062 Page4 of 7

b. Tee in the AccuBoom Cable P/N 115-0171-701 between the Terragator

boom cable and the boom harness cable.

4. Route the CAN and power cables from AccuBoom harness to the main harness.

a. Connect a 12 foot CAN tee cable P/N 115-0171-362 to the CAN

connector located on the AccuBoom Cable P/N 115-0171-701.

b. Route the 12 foot CAN Tee Cable P/N 115-0171-362 and the power cable

from the AccuBoom Cable P/N 115-0171-701 to the CAN and CAN

Power connection located behind the operator ladder.

P/N 016-0171-062 Page5 of 7

5. Connect CAN cable to Product CANbus.

a. Remove the CAN Tee terminator from the Product Control CAN cable

located directly behind the operator ladder.

b. Connect the CAN tee cable P/N 115-0171-362 to the CAN connection

where the CAN Terminator P/N 063-0172-369 was previously removed

from.

c. Connect the CAN Terminator P/N 063-1072-369 to the other Tee end of

the CAN Tee Cable P/N 115-0171-362 located near the AccuBoom node

and secure in place.

P/N 016-0171-062 Page6 of 7

6. Connect power and ground.

a. Locate the CAN power connector located in the area behind the operator

ladder.

b. Connect the power connector from the AccuBoom Cable P/N 115-0171-

701 to the Terragator CAN power connection.

7. The Terragator With Liquid Bed CAN AccuBoom installation is complete.

P/N 016-0171-062 Page7 of 7

SECTION 3

SYSTEM TROUBLESHOOTING

The CAN AccuBoom Node P/N 063-0172-316 has additional features to allow the user

to diagnose the AccuBoom system. The CAN AccuBoom node has a plastic window in

the case that allows the user to view green diagnostic lights. The picture below shows the

positioning and function of each of the LED lights.

Logic Power: Lit when

12VDC logic power is

available at the node.

Micro 1 Hz: Flashes at 1 Hz

interval when processor is

active.

CAN Rx: Flashes when CAN

messages are being received.

CAN Tx: Flashes when CAN

messages are being transmitted.

High Current Power: Lit

when High Current Power is

applied to the node.

Logic Power

Micro 1 Hz

CAN Rx

CAN Tx

High Current Power

Autres manuels pour AccuBoom

Table des matières

Autres manuels Raven Système de contrôle

Raven

Raven AutoBoom Manuel utilisateur

Raven

Raven SBGUIDANCE SMARTRAX MD Manuel utilisateur

Raven

Raven AccuBoom Manuel utilisateur

Raven

Raven DCS 410 Supplément

Raven

Raven SCS 340 Manuel

Raven

Raven AccuBoom Manuel utilisateur

Raven

Raven SmarTrax Manuel utilisateur

Raven

Raven SCS 460 Manuel

Raven

Raven RCM-Sprayer Hawkeye 2 Manuel utilisateur

Raven

Raven RCM-Sprayer Hawkeye 2 Manuel utilisateur

Raven

Raven DCS 300 Manuel

Raven

Raven AccuBoom Manuel utilisateur

Raven

Raven SCS 4600 Manuel utilisateur

Raven

Raven Envizio Pro Manuel utilisateur

Raven

Raven RCM-Sprayer Hawkeye 2 Manuel utilisateur

Raven

Raven AccuBoom Manuel utilisateur

Raven

Raven Viper Pro Manuel utilisateur

Raven

Raven AutoBoom Manuel utilisateur

Raven

Raven RS1 Manuel d'utilisation et d'entretien

Raven

Raven RS1 Manuel utilisateur

Raven

Raven SCS-330 Supplément

Raven

Raven PRECISION AUTOBOOM G1 Manuel utilisateur

Raven

Raven RS1/HDU Manuel utilisateur

Raven

Raven SCS 440 Manuel utilisateur

Manuels Système de contrôle populaires d'autres marques

Pentair Pool Products

Pentair Pool Products Compool Manuel utilisateur

ComfortNET

ComfortNET CTK04 Manuel utilisateur

Fireye

Fireye InSight II 95DSS3 Manuel utilisateur

CAME

CAME G3000 Manuel utilisateur

Idemia

Idemia MorphoAccess VP MD Manuel utilisateur

Axis

Axis P1445-LE-3 Manuel utilisateur

HEIDENHAIN

HEIDENHAIN TNC 150 B Manuel utilisateur

CNC-Step

CNC-Step High-Z T-Series Manuel utilisateur

Doosan

Doosan DVF Series Manuel utilisateur

Honeywell

Honeywell KAP 140 Manuel utilisateur

Honeywell

Honeywell vk41 series Manuel utilisateur

AirBench

AirBench FPW Guide d'installation

Cypress

Cypress HHR-3160 Manuel utilisateur

CAME

CAME GLT40AOS Manuel utilisateur

Zonex

Zonex GEN II -VVT Guide de l'utilisateur

Altronics

Altronics K 9650 Manuel utilisateur

micro-trak

micro-trak RoadMaster Manuel utilisateur

micro-trak

micro-trak Calc-An-Acre II Manuel utilisateur