Raven AccuBoom Manuel utilisateur

Miller Condor G-Series

AccuBoom™ Installation Manual

While every effort has been made to ensure the accuracy of this document,

Raven Industries assumes no responsibility for omissions and errors. Nor is any

liability assumed for damages resulting from the use of information contained

herein.

Raven Industries shall not be held responsible or liable for the effects of

atmospheric conditions and sunspot activity on the performance of our products.

Raven Industries cannot guarantee the accuracy, integrity, continuity, or

availability of the GPS signal from the U.S. Department of Defense/NAVSTAR

GPS satellites, the OmniSTAR correction service or the WAAS correction

service.

Raven Industries accepts no responsibility for the use of the signal for other than

the stated purpose. Raven Industries shall not be responsible or liable for

incidental or consequential damages or a loss of anticipated benefits or profits,

work stoppage or loss or impairment of data arising out of the use, or inability to

use, the SmarTrax or any of its components.

Disclaimer

Table of Contents

Manual No. 016-1001-076 i

Chapter 1 Important Safety Information................................................. 1

Important Safety Information ..................................................................................................... 1

Chapter 2 Introduction............................................................................. 3

Introduction ............................................................................................................................... 3

Recommendations .............................................................................................................. 4

Tools Needed ...................................................................................................................... 4

Preparing for Installation ..................................................................................................... 4

Point of Reference ............................................................................................................... 4

AccuBoom Kit Contents ............................................................................................................ 5

Chapter 3 AccuBoom Installation........................................................... 7

Install the AccuBoom Node .......................................................................................................7

Install the AccuBoom Harness Cable ........................................................................................ 8

Chapter 4 Section Mapping Setup ........................................................ 11

Envizio Pro .............................................................................................................................. 11

Viper Pro ................................................................................................................................. 11

Chapter 5 Troubleshooting ................................................................... 13

Table of Contents

ii Miller Condor G-Series AccuBoom Installation Manual

CHAPTER

Manual No. 016-1001-076 1

C hapt er 1

Important Safety

Information

Important Safety Information

Read this manual and the operation and safety instructions included with your implement and/or controller

carefully before installing the AccuBoom™ system.

•Follow all safety information presented within this manual.

•If you require assistance with any portion of the installation or service of your Raven equipment, contact

your local Raven dealer for support.

•Follow all safety labels affixed to the AccuBoom system components. Be sure to keep safety labels in good

condition and replace any missing or damaged labels. To obtain replacements for missing or damaged

safety labels, contact your local Raven dealer.

When operating the machine after installing AccuBoom, observe the following safety measures:

•Be alert and aware of surroundings.

•Do not operate AccuBoom or any agricultural equipment while under the influence of alcohol or an illegal

substance.

•Remain in the operator’s position in the machine at all times when AccuBoom is enabled.

•Disable AccuBoom when exiting from the operator’s seat and machine.

•Do not drive the machine with AccuBoom enabled on any public road.

•Determine and remain a safe working distance from other individuals. The operator is responsible for

disabling AccuBoom when the safe working distance has been diminished.

•Ensure AccuBoom is disabled prior to starting any maintenance work on AccuBoom or the machine.

•Always verify that the power leads are connected to the correct polarity as marked. Reversing the power

leads could cause severe damage to the equipment.

•Ensure that the power cable is the last cable to be connected.

NOTICE

CAUTION

Chapter 1

2 Miller Condor G-Series AccuBoom Installation Manual

CHAPTER

Manual No. 016-1001-076 3

C hapt er 2

Introduction

Congratulations on your purchase of the Raven AccuBoom system! This system is designed to provide

accurate and cost-efficient application control by avoiding no-spray zones and eliminating wasteful overlaps.

This manual applies to the following machines. For future reference, write your serial number in the space

below.

MAKE: Miller

MODEL: Condor G-Series

YEAR:

SERIAL NUMBER:

FIGURE 1. Miller Condor G-Series

Chapter 2

4 Miller Condor G-Series AccuBoom Installation Manual

Recommendations

Raven Industries recommends the following best practices when installing the AccuBoom system.

•Use part numbers to identify the parts.

•Do not remove the plastic wrap from a part until it is necessary for installation.

Tools Needed

The following tools are recommended for installation of the AccuBoom system:

•SAE standard-sized wrenches

•Cable ties

•Set of tools

Preparing for Installation

Before installing AccuBoom, park the machine where the ground is level, clean, and dry. Leave the machine

turned off for the duration of the installation process.

During the installation process, follow good safety practices. Be sure to carefully read the instructions in this

manual as you complete the installation process.

Point of Reference

The instructions in this manual assume that you are standing behind the machine, looking toward the cab.

Manual No. 016-1001-076 5

Introduction

AccuBoom Kit Contents

This section contains a list of the components that are included in the AccuBoom kit. Before beginning the

AccuBoom installation, compare the items in the AccuBoom kit with the components on this list. If you have

questions about the kit, contact your local Raven dealer.

TABLE 1. AccuBoom Installation Kit (P/N 117-1001-076)

Picture Item Description Part Number Qty.

Not Pictured Manual - Miller Condor G-Series AccuBoom

Installation 016-1001-076 1

Node - CAN AccuBoom 063-0172-316 1

Cable - Miller Condor G-Series CAN

AccuBoom 115-1001-042 1

Bolt - 1/4”-20 x 1” Hex 311-0050-105 3

Nut - 1/4”-20 Nylon Lock 312-4000-057 3

Washer - 1/4” Flat 313-2300-009 6

Chapter 2

6 Miller Condor G-Series AccuBoom Installation Manual

Autres manuels pour AccuBoom

Table des matières

Autres manuels Raven Système de contrôle

Raven

Raven SCS 360 Supplément

Raven

Raven AutoBoom Manuel utilisateur

Raven

Raven AutoBoom Manuel utilisateur

Raven

Raven SCS 460 Manuel

Raven

Raven DCS 300 Manuel

Raven

Raven SCS 440 Manuel utilisateur

Raven

Raven PRECISION AUTOBOOM G1 Manuel utilisateur

Raven

Raven SCS-330 Supplément

Raven

Raven AutoBoom Manuel utilisateur

Raven

Raven RCM-Sprayer Hawkeye 2 Manuel utilisateur

Raven

Raven AccuBoom Manuel utilisateur

Raven

Raven AccuBoom Manuel utilisateur

Raven

Raven AccuBoom Manuel utilisateur

Raven

Raven Viper Pro Manuel utilisateur

Raven

Raven RCM Manuel d'utilisation et d'entretien

Raven

Raven SCS 340 Manuel

Raven

Raven DCS 410 Supplément

Raven

Raven CR Series Manuel utilisateur

Raven

Raven AccuBoom Manuel utilisateur

Raven

Raven RS1/HDU Manuel utilisateur

Raven

Raven SCS 4600 Manuel utilisateur

Raven

Raven RCM-Sprayer Hawkeye 2 Manuel utilisateur

Raven

Raven SmarTrax Manuel utilisateur

Raven

Raven RCM-Sprayer Hawkeye 2 Manuel utilisateur

Manuels Système de contrôle populaires d'autres marques

Pentair Pool Products

Pentair Pool Products Compool Manuel utilisateur

ComfortNET

ComfortNET CTK04 Manuel utilisateur

Fireye

Fireye InSight II 95DSS3 Manuel utilisateur

CAME

CAME G3000 Manuel utilisateur

Idemia

Idemia MorphoAccess VP MD Manuel utilisateur

Axis

Axis P1445-LE-3 Manuel utilisateur

HEIDENHAIN

HEIDENHAIN TNC 150 B Manuel utilisateur

CNC-Step

CNC-Step High-Z T-Series Manuel utilisateur

Doosan

Doosan DVF Series Manuel utilisateur

Honeywell

Honeywell KAP 140 Manuel utilisateur

Honeywell

Honeywell vk41 series Manuel utilisateur

AirBench

AirBench FPW Guide d'installation

Cypress

Cypress HHR-3160 Manuel utilisateur

CAME

CAME GLT40AOS Manuel utilisateur

Zonex

Zonex GEN II -VVT Guide de l'utilisateur

Altronics

Altronics K 9650 Manuel utilisateur

micro-trak

micro-trak RoadMaster Manuel utilisateur

micro-trak

micro-trak Calc-An-Acre II Manuel utilisateur