Quantum Atlas II Manuel de service

Atlas II

Jumper Settings

50-pin Jumper Settings

Jumper Settings

The following describes the jumper options and settings available on the Maxtor® Atlas™ II disk drive.

Maxtor Atlas II was developed by Quantum Corporation prior to its merger with Maxtor.

Termination Enable (TE)

Enable termination TE jumper on

Disable termination TE jumper off

1 of 8

Atlas II

Jumper Settings

Termination Power (TP)

Enable termination power TP jumper on

Disable termination power TP jumper off

SCSI ID (A3, A2, A1, A0)

Set drive SCSI ID See ID settings table below

Delay Spin (DS)

Enable spin delay

SP jumper off

Disable spin delay

SP jumper on

cStagger Spin

Enable spin stagger SS jumper on

Disable spin stagger SS jumper off

Write Protect

Enable W

rite Protection WP jumper on

Disable W

rite Protection WP jumper off

Jumper Locations

The Atlas II disk drive has two locations where user configurable jumpers are found. The primary jumper block (Front option

connector J3) for the Atlas II is found on the front edge of the disk drive printed circuit board. Using these jumper pins you

can establish the various drive configuration options. The second option jumper block is used to set the Atlas II termination

options. This jumper block is found on the printed circuit board at the rear of the drive and is near the SCSI cable connector.

2 of 8

Atlas II

Jumper Settings

28-Pin Secondary Option Connector

ignal P

in S

ignal

logic_gnd

Fault LED

key (blank)

Busy LED

0 Spindle Sync

+5VDC out

2 unused

Delay Spin

4 logic_gnd

Stagger Spin

6 logic_gnd

Write Protect

8 logic_gnd

Spindle Sync

0 logic_gn

The drawing above displays the jumper block physical location and pin definitions.

3 of 8

Atlas II

Jumper Settings

SCSI ID Settings

The following table identifies the various SCSI ID values and the jumper positions required to set them.

Drive ID

ID 0

OFF

ID 1

OFF

ID 2

OFF

ID 3

OFF

ID 4

OFF

ID 5

OFF

ID 6

OFF

ID 7

4 of 8

Atlas II

Jumper Settings

68-pin Jumper Settings

Jumper Settings

The following describes the jumper options and settings available on the Maxtor® Atlas™ II disk drive. Maxtor Atlas II was

developed by Quantum Corporation prior to its merger with Maxtor.

Termination Enable (TE)

Enable termination TE jumper on

Disable termination TE jumper off

Note: Termination enable available on SE version only.

Termination Power (TP)

Enable termination power TP jumper on

Disable termination power TP jumper off

SCSI ID (A3, A2, A1, A0)

Set drive SCSI ID See ID settings table below

Delay Spin (DS)

Enable spin delay

Disable spin delay

SP jumper off

SP jumper on

5 of 8

Atlas II

Jumper Settings

6 of 8

Stagger Spin

Enable spin stagger SS jumper on

Disable spin stagger SS jumper off

Write Protect

Enable Write Protection

WP jumper on

Disable W

rite Protection WP jumper off

Jumper Locations

The Atlas II wide disk drive has two locations where user configurable jumpers are found. The primary jumper block (Front

option connector J3) for the Atlas II wide is found on the front edge of the disk drive printed circuit board. Using these

jumper pins you can establish the various drive configuration options. The secondary option jumper block provides an

alternate method for setting primary drive features. The alternate jumper block is located at the rear of the drive and is

incorporated into the SCSI cable connector.

The termination power option setting is located on the front edge of the printed circuit board and is adjacent to the J3

connector.

Atlas II

Jumper Settings

7 of 8

Signal

ogic_gnd

Key

(blank) 1

0 F

ault LED

Delay

Spin 1

2 l

ogic_gnd

Logic ground

4 E

nable Active Termination

Spindle Sync

6 S

pindle Sync

Busy Led

8 +

5VDC out

rite Protect 2

0 l

ogic_gnd

Stagger Spin

2 l

ogic_gnd

Enabl

e Narrow Mode 2

4 l

ogic_gnd

Disable Sync Negotiation

6 l

ogic_gnd

Disable SCSI Parity

8 l

ogic_gnd

Disable Unit Attentio

n 3

0 l

ogic_gnd

Customize

2 l

ogic_gnd

Signal

in S

ignal

ault LED

ogic_gnd

usy LED

Enable Ter

mination 1

0 l

ogic_gnd

+5VDC out

2 (

reserved)

Note: Enable Termination setting is not supported on the following differential drives:

Atlas II 2.2GB WD

Atlas II 4.5GB WD

Atlas II

Jumper Settings

Atlas II 9.1GB WD SCSI ID SettingsThe following table identifies the various SCSI ID values and the jumper positions

required to set them.

Drive ID

ID 0

OFF

ID 1

OFF

ID 2

OFF

ID 3

OFF

ID 4

OFF

ID 5

OFF

ID 6

OFF

ID 7

OFF

ID 8

OFF

ID 9

OFF

ID 10

OFF

ID 11

OFF

ID 12

OFF

ID 13

OFF

ID 14

OFF

ID 15

8 of 8

Table des matières

Autres manuels Quantum Stockage

Quantum

Quantum ValueLoader LTO-2 Manuel utilisateur

Quantum

Quantum Maxtor Fireball lct10 Manuel utilisateur

Quantum

Quantum Scalar i500 Manuel utilisateur

Quantum

Quantum DLTtape DLT 2000 Manuel

Quantum

Quantum Scalar LTFS Manuel d'utilisation et d'entretien

Quantum

Quantum Scalar i500 Manuel utilisateur

Quantum

Quantum RDX 8000 Manuel utilisateur

Quantum

Quantum DLTtape DLT 4000 Manuel utilisateur

Quantum

Quantum Q250 Manuel du produit

Quantum

Quantum DAT 160 Manuel de service

Quantum

Quantum Superloader 3 Manuel utilisateur

Quantum

Quantum StorNext QD7000 Manuel

Quantum

Quantum FastStor 2 Manuel utilisateur

Quantum

Quantum DXi4510 Manuel de l'opérateur

Quantum

Quantum P1000 Series Manuel utilisateur

Quantum

Quantum Scalar 100 Manuel utilisateur

Quantum

Quantum Scalar i500 Manuel utilisateur

Quantum

Quantum ActiveScale P100E3 Manuel utilisateur

Quantum

Quantum Scalar LTFS Manuel de la liste des pièces

Quantum

Quantum DLTtape DLT 8000 Manuel utilisateur

Quantum

Quantum P4000 Series Instructions d'installation et d'utilisation

Quantum

Quantum Scalar i500 Manuel utilisateur

Quantum

Quantum StorNext QD7000 Manuel utilisateur

Quantum

Quantum StorNext AEL500 Manuel utilisateur

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

HP StorageWorks MSL2024 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

HP P9000 Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur