Provision ISR Z-22IR Manuel utilisateur

Package Contents:

Item Qty.

Z-2 2/2 7 IR PTZ 1

Wall Bracket 1

Hinge Pin 1

Rubber Seal 1

DC12V/5A power supply 4

Wall Screws 4

PM8*25 socket head screws 1

Allan Key 1

User Manual

Table of Contents:

1 General Instructions...................................................................................... 3

1.1 Safety Instructions ............................................................................ 3

1.2 Warnings........................................................................................... 3

2 Features ........................................................................................................ 4

2.2 Product Features............................................................................... 4

2.3 Specifications.................................................................................... 5

3 Installation Site Preparations ........................................................................ 6

3.1 Tool List............................................................................................. 6

3.2 Installation Preparation .................................................................... 6

3.3 DIP Switch Setup............................................................................... 7

4 Setup of the OSD Menu ................................................................................ 8

4.1 Display Boot-UP Info........................................................................... 8

4.2 Enter the OSD Menu......................................................................... 9

4.3 SYSTEM ........................................................................................... 10

4.4 LENS................................................................................................ 15

4.5 CAMERA.......................................................................................... 17

4.6 PAN/TILT ....................................................................................... 211

4.7 AUTO RUNNING.............................................................................. 22

4.8 PRIVACY MASK................................................................................ 29

4.9 ALARM.......................................................................................... 300

4.10 LANGUAGE.................................................................................. 311

4.11 IR SET .......................................................................................... 322

APPENDIX I: DIP Switch Setting...................................................................... 33

APPENDIX II Shortcuts Key Chart ............................................................... 3838

APPENDIX III Trouble Shooting..................................................................... 400

1 General Instructions:

1.1 Safety Instructions:

Make sure to read the user manual before using the product.

Always follow national and local safety codes during the installation.

Only qualified and experienced person can carry this installation and

maintenance.

Use reliable tools, not complying can result in serious injury.

Make sure that the environmental conditions meet the installation

requirements for this product.

Please check the space and toughness of the site before installing. It

should be able to bear 4 times the weight of the dome and its

accessories.

1.2 Warnings:

Do not install this speed dome in hazardous places where combustible

or explosive materials are stored or used.

Do not install on platform that suffers from constant vibrations.

Make sure no object or fluid substances get inside the unit.

This speed dome runs on DC 12V, do not connect it to higher or lower

voltage.

Do not turn power on before installation is complete.

Do not disassemble any part of the items.

Use soft towel to clean the down cover when necessary, do not use

caustic detergent.

To protect CCD, avoid facing the camera directly into strong light.

To prevent damage, do not drop the unit or allow to strong shocks or

vibrations.

Make sure no object is blocking the unit’s full range of motion.

2 Features:

2.1 Product Picture:

2.2 Product Features

Alarm I/O.

Adaptive PELCO-P/D protocol.

Adjustable IR illumination.

Memory recall.

Real-Time-Control: call any functions at any time.

Up to 8 privacy masks.

Support 128 preset positions.

English OSD menu, user friendly for smooth operation.

Proportional zoom.

Auto flip function.

Built in lightning proof and surge proof.

Advanced step motor: Less heat, Smooth movement, No-shaking.

Efficient heating device, ensure to work in -20°low temperature.

Support 4 groups cruise scan (27 presets/group), 4 group patterns, one

scan, and 360°continuous scan and 360° intermittent scan.

IR lights automatically adjust the light intensity according to the zoom

speed to reduce the dark angle and flashlight effect.

The upper dome adopts 7" aluminum alloy structure for better

magnetic shield and heat radiation.

The underpart dome adopts full metal class points bin type design for

fast heat dissipation and anti-mist, non-interference light source images

and long life span IR light.

2.3 Specifications:

Power Supply Input：AC100～240V 50/60Hz

Output：DC12V±5%，5A

Max. Power

Consumption

IR off：15W

IR on：31W

Sync system Internal Sync

Language English

Pan Speed 0.08°～240°/S

Tilt Speed 0.08°～240°/S

Pan Range 0°～360°(Continuous)

Tilt Range 0°～90°（180° auto flip）

Preset 128

Preset Accuracy <±0.1°

Tour 4, 27 presets/tour

Pattern 4

Zone 1

Protocol RS485

Communication PELCO-D/P auto detected

Baud Rate 2400bps、4800bps、9600bps、19200bps

Address 1-255 (By DIP Switch or Software)

RTC Set any functions at any time

IR Light switch

Superpower LED：Default: Zoom x1~5: open the

near-

distance IR lights; Zoom x6~9: open the

near-distance and middle-d

istance IR lights;

Zoom >x10: turn off the near-distance IR lights,

open the middle-distance and far-

distance IR

lights.

Work

Temperature

Indoor：0

℃

～+50

℃

；

Outdoor ：-20

℃

～+50

℃

(with heater)

Work Humidity <90%

3 Installation Site Preparations:

3.1 Tool List:

(1) Screws* (2) Monkey wrench

(3) Philips screwdriver (4) Straight Screwdriver

(5) Wire stripper (6) Socket head wrench

(7) Electric drill (8) Hammer

(9) BNC connector (10) BNC Clamp

*Included in the kit

3.2 Installation Preparation:

(1) Check the space and toughness of the site and make sure that the

environmental conditions meet the installation requirements for this product.

(2) The installation surface should be able to bear 4 times the weight of the

PTZ and its accessories.

3.3 DIP Switch Setting:

(1)Default Settings: Pelco P/D (auto-detected), baud rate: 2400, address: 1.

Use Philips screwdriver to remove the DIP switch cover (see location below)

(2)Baud Rate Setup

Decoder Switch: 9~10 (1=ON, 0=OFF)

Switch 9-10 setting

Baud Rate Max transmission

distance(M)

9 10

0 0 2400BPS 1800

1 0 4800BPS 1200

0 1 9600BPS 800

1 1

Auto detected 2400、

4800、9600、

19200BPS

600-1800

(3) When the DIP Switch 9th and 10th are ON, the PTZ can automatically

detected the baud rate 2400, 4800,9600,19200

(4) Hardware Address Setup*: Please refer to Appendix I.

*Please note that the address setting can also be configured via the

software using the camera OSD (Page 11).

DIP Switch

Position Reset Position

4 Setup of the OSD Menu:

4.1 Display Boot-UP Info.

Before installation please check the protocol, baud rate, address and RS485

data cable. Default protocol: PELCO-D, address: 1, baud rate: 2400.

When starting, the PTZ will display the following information:

Once done, the above information will disappear and the user will gain

control over the camera.

4.2 Enter the OSD Menu:

While the camera is in standby condition, call preset 95 (“Call” + 95 + “Enter”)

in order to display the main menu. Use the Up/Down direction to select item

or start the configuration. Use the Right key to confirm and left key for exit

the current setting.

Level self-check: Success

Vertical self-check: Success

Camera type: ####

Success

PROTOCOL: PELCO P D

BAUD RATE: 2400BPS

CAMERA ID: 001

CAMERA S/N: 0000000001

MODEL: -----------------

VERSION: V1.02

FAN SPEED: 6000RPM

STARTING… ….

The Main menu as follows:

4.3 SYSTEM Menu:

SITE INFO

DISPLAY SETUP

BOOTUP SCREEN

PASSWORD

SET DEFAULT

SYSTEM REBOOT

RTC TIME SET

RTC TIMER RUNNING

BACK

EXIT

SYSTEM

LENS

CAMERA

PAN/TILT

AUTO RUNNING

PRIVACY MASK

ALARM

LANGUAGE

IR SET

EXIT

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Provision ISR Caméra de sécurité

Provision ISR

Provision ISR IP Series Manuel utilisateur

Provision ISR

Provision ISR I3-380IP04 Manuel utilisateur

Provision ISR

Provision ISR PT-848 Manuel utilisateur

Provision ISR

Provision ISR PRO-AHD series Manuel utilisateur

Provision ISR

Provision ISR ZP-20A-2(IR) Manuel utilisateur

Provision ISR

Provision ISR PT-737 Instructions d'utilisation et d'entretien

Provision ISR

Provision ISR DAI-390IPVF Manuel utilisateur

Provision ISR

Provision ISR ISR BOX CAMERA Manuel utilisateur

Provision ISR

Provision ISR DA-352CS DA-322CS Manuel utilisateur

Provision ISR

Provision ISR I2-320A-28 Manuel utilisateur

Provision ISR

Provision ISR Effio-E Infra Red Manuel utilisateur

Provision ISR

Provision ISR PT-737 Manuel utilisateur

Provision ISR

Provision ISR I5PT-390IPX4 Manuel utilisateur

Provision ISR

Provision ISR PI Series Manuel utilisateur

Provision ISR

Provision ISR BX-380IP Manuel utilisateur

Provision ISR

Provision ISR UltraVision Series Manuel utilisateur

Provision ISR

Provision ISR Mini Ultra-Z Z-10AHD-1 (IR) PTZ Manuel utilisateur

Provision ISR

Provision ISR I5PT-320IPMX10-P Manuel utilisateur

Provision ISR

Provision ISR DI-380AHD36 Manuel utilisateur

Provision ISR

Provision ISR DAIPT-390AX4 Manuel utilisateur

Provision ISR

Provision ISR I1-380AHDB36 Manuel utilisateur

Provision ISR

Provision ISR Ultra-Z IP series Manuel utilisateur

Provision ISR

Provision ISR I1-325CS Manuel utilisateur

Provision ISR

Provision ISR AUTO SYNC FOCUS SERIES Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur