Power Fist Air Hammer Manuel utilisateur

8435893

User Manual

Air Hammer with

3 pc Chisels

Please read and understand all instructions before use.

Retain this manual for future reference.

V 2.1

8435893

Air Hammer with

3 pc Chisels

For technical questions call: 1-800-665-8685

V 2.

SPECIFICATIONS

Type 3 pc

Air Consumption @ 90 PSI 5 CFM

Impact Rate 3,600 BPM

Stroke Length 2 in.

Housing Gravity die-casting

Max. Pressure 120 PSI

SAFETY

IMPORTANT SAFETY PRECAUTIONS

WARNING! Read and understand all instructions before using this tool. The operator must follow basic

precautions to reduce the risk of personal injury and/or damage to the equipment. Before allowing

someone else to use this tool, make sure they are aware of all safety information.

WARNING! The warnings, cautions and instructions discussed in this instruction manual cannot cover

all possible conditions and situations that may occur. Common sense and caution are factors that

cannot be built into this product, but must be supplied by the operator.

NOTE: Keep this manual for safety warnings, precautions, operating, inspection and

maintenance instructions.

Air Hammer with 3 pc Chisels

4For technical questions call: 1-800-665-8685

8435893V 2.1

WORK AREA

1. Operate in a safe work environment. Keep your work area clean and well lit.

2. Do not use in the presence of ﬂammable gases or liquids.

3. Keep anyone not wearing the appropriate safety equipment away from the work area.

4. Minimize distractions in the work environment. Distractions can cause you to lose

control of the tool.

5. Store tools properly in a safe and dry location to prevent rust or damage.

6. Always lock up tools and keep them out of the reach of children.

PERSONAL SAFETY

CAUTION! Wear protective equipment approved by the Canadian Standards Association (CSA) or

American National Standards Institute (ANSI) when using the tool.

1. Head Protection

a. Always wear impact safety goggles that provide front and side protection for the eyes.

b. Wear the appropriate rated dust mask or respirator.

c. Wear earplugs if the power tool or work environment is noisy.

d. Wear a full-face shield if your work creates metal ﬁlings or wood chips.

e. Wear a hard hat to protect your head from falling objects.

2. Gloves

a. The gloves should provide protection based on the work materials.

b. Wear suitable gloves to reduce the effects of vibration.

3. Protective Clothing

a. Wear protective clothing designed for the work environment and tool. Examples are

electrical non-conductive clothes or clothes treated to resist corrosive liquids or materials.

4. Foot Protection

a. Steel toe footwear or steel toe caps to prevent injury from falling objects.

b. Non-skid footwear is recommended to maintain footing and balance.

5. Control the tool, personal movement and the work environment to avoid personal injury or

damage to tool. Stay alert, watch what you are doing and use your common sense.

a. Keep articles of clothing, jewelry, hair, etc., away from moving parts to avoid entanglement

with a tool.

b. Do not operate any machine/tool when tired or under the inﬂuence of drugs,

alcohol or medications.

c. Do not overreach when operating a tool. Proper footing and balance enables better control

of a tool in unexpected situations.

d. Use clamps or other practical ways to support or secure the workpiece to a stable

platform. Holding the workpiece by hand or against your body is not stable and may lead

to loss of control and injury.

Air Hammer with 3 pc Chisels

Visit www.princessauto.com for more information

8435893 V 2.

VIBRATION PRECAUTIONS

1. This tool vibrates during use. Repeated or long-term exposure to vibration may cause

temporary or permanent physical injury, particularly to the hands, arms and shoulders.

2. Anyone using vibrating tools regularly or for an extended period should ﬁrst be examined by

a doctor and then have regular medical check ups to ensure medical problems are not being

caused by or worsened from tool use.

3. If you feel any medical symptoms related to vibrations (such as tingling, numbness, and white

or blue ﬁngers), seek medical attention as soon as possible.

4. DO NOT use this tool if one of the following applies:

a. Pregnant

b. Impaired blood circulation to the hands

c. Past hand injuries

d. Nervous system disorders

e. Diabetes

f. Raynaud’s Disease

5. Do not smoke while operating the tool. Nicotine reduces the blood ﬂow to the hands and

ﬁngers, increasing the risk of vibration-related injury.

6. Wear suitable gloves to reduce the effects of vibration.

7. Use the tool with the least amount of vibration, when there is a choice between

different processes.

8. Do not use for extended periods. Take frequent breaks to when using this tool.

9. Let the tool do the work. Grip the tool as lightly as possible

(while still keeping safe control of it).

10. To reduce vibrations, maintain the tool as explained in this manual. If abnormal vibrations

occur, stop using this tool immediately.

Air Hammer with 3 pc Chisels

6For technical questions call: 1-800-665-8685

8435893V 2.1

TOOL USE AND CARE

1. Use the correct tool for the job. Do not force a tool or attachment to do the work of a larger

industrial tool. Maximize tool performance and safety by using the tool for its intended task.

2. This tool was designed for a speciﬁc function. Do not modify or alter this tool or use it for an

unintended purpose.

3. Securely hold this tool using both hands, unless it is designed for single hand use.

Using a tool with only one hand can result in loss of control.

4. Maintain tools with care (see Maintenance).

5. Remove adjusting keys and wrenches from the tool before operation or connecting it to a power

source. A wrench or key that is left attached to a rotating part of the tool increases the risk of

personal injury.

6. Avoid unintentional starts. Be sure that the throttle/ignition switch is in the neutral or OFF

position when not in use and before connecting it to any air source.

7. Do not carry the tool with ﬁngers near or on the trigger/switch.

AIR COMPRESSOR

Ensure the compressor used with the tool can supply the required Cubic Feet per Minute at the required

PSI (see Speciﬁcations).

1. Use proper size and type of air pressure line and ﬁttings.

2. Use only clean, dry, regulated compressed air at the rated range as marked on the tool.

CAUTION! Do not use an air source other than an air compressor to power this tool.

3. Always use an air regulator, an in-line

ﬁlter and a moisture trap in your

compressed air system. These

accessories will increase the tool’s life

and keeps the tool in good working

condition. See the diagram for

recommended components of

an air line.

4. Avoid using an air hose that is too long.

The longer the hose, the lower the

pressure that reaches the tool, possibly

causing it to cease functioning.

As well, a longer hose can become a

tripping hazard.

5. Air tool CFM consumption ratings

are based upon a 25% duty cycle. If

you require continuous duty, a larger

compressor is required. Figure. 1

Air Hammer with 3 pc Chisels

Visit www.princessauto.com for more information

8435893 V 2.

AIR SOURCE INSTALLATION

WARNING! Never use pure oxygen, carbon dioxide, combustible gases or any bottled gas as an air

source for a tool. Such gases are capable of causing an explosion and serious injury to persons.

1. Set the air pressure regulator on the air compressor to the recommended PSI level (see

Speciﬁcations). Do not exceed the tool recommended air pressure. Excess pressure could

result in damage to the tool, to your workpiece or serious injury.

2. Prepare a standard 1/4 in. air connector for use with your tool. Wrap the threaded portion of

the air connector with thread tape. Wrap in a clockwise direction so it will not unravel when

attaching to a quick connector. Attach it to the tool air inlet and tighten.

3. Attach a standard quick connector to the air source’s hose. Attach the air hose to

the tool’s air connector.

4. Check the air line and its connections for air leaks. Do not use the tool until you have

repaired all air leaks.

DISCONNECTING AIR SOURCE

WARNING! Failure to follow these steps could result in severe injury, tool or property damage.

Disconnect tool from air source before cleaning, servicing, changing parts/accessories or

when not in use.

1. Turn hopper regulator to the OFF position.

2. Turn the air regulator to the OFF or L position.

3. Turn off the air compressor.

4. Disconnect the air pressure hose.

5. Discharge any residual pressure inside the tool.

Air Hammer with 3 pc Chisels

8For technical questions call: 1-800-665-8685

8435893V 2.1

AIR TOOL LUBRICATION

CAUTION! NEVER use a penetrating oil to lubricate the tool. Penetrating oil may act as a solvent that

will break down the grease and cause the tool to seize up.

1. All air tools are packed in grease to prevent corrosion of internal parts during shipping and

storage. We recommend you clean this out to have optimum performance from your new air

tool. Add a generous amount of air tool oil in the air inlet, and then run the tool under no load

until exhaust is clear to remove packing grease.

2. It is very important that the tool is lubricated. Without lubrication, the tool will not work

properly and parts will wear prematurely. Manually adding a drop or two of air tool oil into the

tool’s male connector once a day is better than using an automatic in-line lubricator. In-line

lubricators should only be required when there are multiple users of the same tool.

3. Air tool oil is the only recommended lubricant for use in all air tools. Do not use other types of

lubricants to oil your tools. Using the wrong lubricant will cause premature tool failure

and/or loss of power. Substitutes may harm the rubber compounds in the tool’s O-rings

and other seals.

4. Keep the airline lubricator ﬁlled and correctly adjusted. The in-line lubricator should be regularly

checked and ﬁlled with air tool oil. Proper adjustment of the in-line lubricator is performed by

placing a sheet of paper next to the exhaust ports and holding the throttle open approximately

30 seconds. The lubricator is properly set when a light stain of oil collects on the paper.

Excessive amounts of oil should be avoided.

5. Avoid adding too much air tool oil during normal use. Too much oil can cause premature power

loss and eventual tool failure. The tool will need to be taken apart by a qualiﬁed technician and

cleaned of excess oil.

6. In the event that it becomes necessary to store the tool for an extended period of time

(overnight, weekend, etc.), it should receive a generous amount of lubrication at that time.

The tool should be run for approximately 30 seconds to ensure oil has been evenly distributed

throughout the tool. The tool should be stored in a clean and dry environment.

Air Hammer with 3 pc Chisels

Visit www.princessauto.com for more information

8435893 V 2.

AIR TOOL PRECAUTIONS

1. Air tools produce more noise than their electric counterparts. Extended exposure to this noise

may cause hearing loss.

a. Wear ear protection gear to eliminate or reduce the noise.

b. If possible add a mufﬂing device to the air tool’s exhaust.

2. Do not operate this tool if the air hose is damaged.

a. Inspect the tool’s air line for cracks, fraying or other faults before each use.

b. Discontinue use if a hissing can be heard from the air line or connectors while operating

the tool.

c. Take the following steps if either of the above situations occur:

i. Tag or mark the tool as 'defective' or 'out of service' until repaired.

ii. Contact a qualiﬁed person repair or replace the defective component/hose.

3. Prevent damage to air hose by observing the following:

a. Never use the hose to carry the tool.

b. Keep the air hose of the tool and the tool’s work path while in operation. The hose should

always stay behind the tool.

c. Keep the hose away from heat, oil, sharp edges or moving parts.

d. Do not allow people, mobile equipment or vehicles to pass over unprotected air hose.

i. Position air hose away from trafﬁc areas.

ii. Place hose in reinforced conduit.

iii. Place planks on either side of the hose to create a protective trench.

e. Do not wrap hose around the tool as sharp edges may pierce the hose or cause cracks if

wound too tight. Gently coil the hose and either hang on a hook or fasten with a device to

keep hose together when storing.

4. An air hose under pressure that is damaged or disconnected from an air tool may whip around

and cause damage to the work area or personal injury. Secure the compressor’s air hose to a

ﬁxed or permanent structure with clamps or cable ties.

Air Hammer with 3 pc Chisels

10 For technical questions call: 1-800-665-8685

8435893V 2.1

AIR POWER TOOL PRECAUTIONS

WARNING! Immediately switch off the power tool if any of the following occurs:

• Malfunction of the air inlet, air compressor or damage to the air supply hose.

• The switch or trigger is broken.

• User sees or smells smoke.

• The user smells the odor of scorched insulation.

• The chisel moves in an unsafe way.

1. Ensure air source matches the pressure rating of the tool’s motor (see Speciﬁcations).

2. Make sure the power switch is in the OFF position before connecting the tool to the air source.

3. Do not place the tool down until the chisel has stopped moving.

The chisel may catch the surface of work material and wrench itself free, causing injury to the

user or others in the work area.

4. Never use a tool with a cracked or worn chisel. Change the chisel before use.

5. Always use both hands when operating the tool, unless the tool is designed for single hand use.

6. Hold tool by insulated gripping surfaces when performing an operation where it may contact

hidden wiring or its own cord. Contact with a live wire will electrify exposed metal parts and

shock the operator.

7. Before using the tool on a work piece, test the tool by running it at the highest no-load speed

for at least 30 seconds in a safe position. Stop immediately if there is any abnormal vibration or

wobbling that could indicate poor installation of the chisel. Check the tool to determine

the cause.

8. Take work breaks to prevent the tool’s motor from overloading and/or overheating.

9. When the tool is in operation, keep hands away from the chisel and the area it is

being applied to.

10. Do not use the tool on any material containing asbestos.

11. Do not touch the chisel or the surface that has been cut with this tool immediately after use.

The surface will be hot and may cause an injury.

12. Do not allow persons who are not familiar with the tool or have not read these instructions to

use the tool.

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Power Fist Outils

Power Fist

Power Fist 8603094 Manuel utilisateur

Power Fist

Power Fist 8665549 Manuel utilisateur

Power Fist

Power Fist 8685042 Manuel utilisateur

Power Fist

Power Fist 8843799 Manuel utilisateur

Power Fist

Power Fist Metal Punch Kit Manuel utilisateur

Power Fist

Power Fist 8880940 Manuel utilisateur

Power Fist

Power Fist 8655888 Manuel utilisateur

Power Fist

Power Fist 8668402 Manuel utilisateur

Power Fist

Power Fist 8957425 Manuel utilisateur

Power Fist

Power Fist 8843773 Manuel utilisateur

Power Fist

Power Fist 8074668 Manuel utilisateur

Power Fist

Power Fist 9004391 Manuel utilisateur

Power Fist

Power Fist 8814436 Manuel utilisateur

Power Fist

Power Fist 8505547 Manuel utilisateur

Power Fist

Power Fist 8063927 Manuel utilisateur

Power Fist

Power Fist 8663783 Manuel utilisateur

Power Fist

Power Fist 8662330 Manuel utilisateur

Power Fist

Power Fist 8623159 Manuel utilisateur

Power Fist

Power Fist 8774465 Manuel utilisateur

Power Fist

Power Fist Air Line Delivery Kit Manuel utilisateur

Power Fist

Power Fist 8308231 Manuel utilisateur

Power Fist

Power Fist 8502494 Manuel utilisateur

Power Fist

Power Fist 8916793 Manuel utilisateur

Power Fist

Power Fist 8517393 Manuel utilisateur

Manuels Outils populaires d'autres marques

Martor

Martor SECUNORM 175 Manuel utilisateur

ERKCO

ERKCO 1000 Manuel utilisateur

jbc

jbc N4473 Manuel utilisateur

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuel utilisateur

Worx Professional

Worx Professional Sonicrafter WU676 Manuel utilisateur

Gage Bilt

Gage Bilt GB713SH Manuel utilisateur

Hilti

Hilti DX 9-ENP Manuel utilisateur

norbar

norbar NORTRONIC 34399 Manuel utilisateur

BGS technic

BGS technic 8578 Manuel utilisateur

Makita

Makita DHR241 Manuel utilisateur

Motor Guard

Motor Guard JMB-1250 Manuel utilisateur

Power Adhesives

Power Adhesives 805-12 Manuel utilisateur

Clemco

Clemco 24189 Manuel utilisateur

VVG

VVG VNG 903 Series Manuel utilisateur

Hilti

Hilti FX 3-A Manuel utilisateur

Grizzly

Grizzly H6472 Manuel utilisateur

axing

axing BWZ 5-02 Manuel utilisateur

Dh-Robotics

Dh-Robotics RGI-100 Comment utiliser