Power Fist 8662330 Manuel utilisateur

V4.0 8662330

Please read and understand all instructions before use. Retain this manual for

future reference.

User Manual

DigitalAngleFinder

8662330 Digital Angle Finder V4.0

2 For technical questions call 1-800-665-8685

SPECIFICATIONS

Length 15 in. (380 mm)

Measuring Accuracy for Angle +/- 0.5°

Display LCD Screen

Vials Number 2

Accuracy 0.5 mm/m

Battery 9V (not included)

Operating Temperature 0

℃

to 50

℃

Storage Temperature 20

℃

to 85

℃

Automatic Power Off Approx. 5 Minutes

SAFETY

WARNING! Read and understand all instructions before using this tool. The

operator must follow basic precautions to reduce the risk of personal injury

and/or damage to the equipment.

Keep this manual for safety warnings, precautions, operating or inspection and

maintenance instructions.

HAZARD DEFINITIONS

Please familiarize yourself with the hazard notices found in this manual. A notice

is an alert that there is a possibility of property damage, injury or death if certain

instructions are not followed.

DANGER! This notice indicates an immediate and specific hazard that will

result in severe personal injury or death if the proper precautions

are not taken.

DigitalAngleFinder

V4.0 Digital Angle Finder 8662330

Visit www.princessauto.com for more information 3

WARNING! This notice indicates a specific hazard or unsafe practice that

could result in severe personal injury or death if the proper

precautions are not taken.

CAUTION! This notice indicates a potentially hazardous situation that may result

in minor or moderate injury if proper practices are not taken.

NOTICE! This notice indicates that a specific hazard or unsafe practice will

result in equipment or property damage, but not personal injury.

WORK AREA

1. Operate in a safe work environment. Keep your work area clean, well-lit

and free of distractions.

2. Keep anyone not wearing the appropriate safety equipment away from the

work area.

3. Store unused tools properly in a safe and dry location to prevent rust or

damage. Lock tools away and keep out of the reach of children.

PERSONAL SAFETY

WARNING! Wear personal protective equipment approved by the Canadian

Standards Association (CSA) or American National Standards Institute (ANSI).

PERSONAL PROTECTIVE EQUIPMENT

1. Always wear impact safety goggles that provide front and side protection

for the eyes. Eye protection equipment should comply with CSA Z94.3-07

or ANSI Z87.1 standards based on the type of work performed.

2. Wear gloves that provide protection based on the work materials or to

reduce the effects of tool vibration.

PERSONAL PRECAUTIONS

Control the tool, personal movement and the work environment to avoid

personal injury or damage to tool.

1. Do not operate any tool when tired or under the influence of drugs, alcohol

or medications.

2. Do not overreach when operating a tool. Proper footing and balance

enables better control in unexpected situations.

8662330 Digital Angle Finder V4.0

4 For technical questions call 1-800-665-8685

SPECIFIC SAFETY PRECAUTIONS

WARNING! DO NOT let comfort or familiarity with product (gained from

repeated use) replace strict adherence to the tool safety rules. If you use

this tool unsafely or incorrectly, you can suffer serious personal injury.

1. Use the correct tool for the job. This tool was designed for a specific

function. Do not modify or alter this tool or use it for an unintended purpose.

2. The tool’s edges may be sharp. Handle carefully to avoid a laceration.

3. Do not expose the tool to rain or wet conditions.

UNPACKING

WARNING! Do not operate the tool if any part is missing. Replace the

missing part before operating. Failure to do so could result in a malfunction

and personal injury.

Remove the parts and accessories from the packaging and inspect for damage.

IDENTIFICATION KEY

A Fold-out Arm

B Joint Cover

C Base

D ON/OFF Button

E Mitre Button

F Hold Button

G LCD Screen

H Vial for Horizontal Alignment

I Vial for Vertical Alignment

J End Cap

K Contact Edge

L Measurement Reading

M Low Battery Indicator

N Mitre (MTR) Indicator

O Hold (HOLD) Indicator

Fig. 1

V4.0 Digital Angle Finder 8662330

Visit www.princessauto.com for more information 5

OPERATION

NOTICE! The angle finder is a precision measuring instrument. Dropping or

banging the device may result in impaired function or inaccurate readings.

Letter references in parenthesis (A) refer to the included Identification Key.

Dashed numbers in parenthesis (Fig. 1-1) refer to a specific point in an

illustration or image

SWITCHING ON AND OFF

Press the ON/OFF button (D) to activate/deactivate the Angle Finder’s LCD Screen (G).

The screen will shut off automatically to preserve batter power after approximately 5

minutes if no buttons are pressed or the fold-out arm (A) isn’t moved.

MEASURING ANGLES

Position the fold-out arm (A) and the base (C) flat

against the two surfaces that form the angle (Fig. 2).

The displayed reading corresponds with the internal

angle (Fig. 2-1) between the base and the fold-out

arm. The reading is indicated on the display until the

arm or base is moved in relation to each other.

HOLD THE MEASURED VALUE

Retain the current reading by pressing the HOLD button (F). The word HOLD

appears in the display and will not change until the HOLD button is pressed

again. Moving the fold-out arm (A) will not affect the reading.

TRANSFERRING THE MEASURED ANGLE

Measure the angle and note the angle displayed in the LCD screen (G) move the

angle finder to the workpiece without moving the fold-out arm (A) or base (C).

Check that the angle reading is the same and mark the workpiece (Fig. 3).

The second method is to measure the angle, press HOLD to retain the angle and

record it. You can turn the angle finder off until ready to transfer the angle.

Fig. 2

8662330 Digital Angle Finder V4.0

6 For technical questions call 1-800-665-8685

When the workpiece is ready, turn the angle finder

on again and adjust the fold-out arm until the LCD

screen reading matches the recorded angle. Place

the angle finder on the workpiece and mark the

angle (Fig. 3).

CHANGING THE ANGLE TO A

MITRE ANGLE

Measure the angle and press the HOLD button

(F). Press the MTR button (E) to convert the angle to the correct mitre angle.

Set your mitre saw to this angle for the cut.

CARE & MAINTENANCE

1. Maintain the tool with care. A tool in good condition is efficient, easier to

control and will have fewer problems.

2. Inspect the tool components periodically. Repair or replace damaged or

worn components. Only use identical replacement parts when servicing.

3. Maintain the tool’s labels and name plates. These carry important information.

If unreadable or missing, contact Princess Auto Ltd. for replacements.

WARNING! Only qualified service personnel should repair the tool. An

improperly repaired tool may present a hazard to the user and/or others.

REPLACE THE BATTERY

Change the battery when the LOW BAT (battery) indicator

(M) appears in the LCD Screen (G). Measurements are still

possible when the battery is low, but the readings may be

inaccurate.

Remove the two screws and pull off the end cap (J). Take

the battery out and disconnect it from the battery snap.

Install a new battery, ensuring the terminals are firmly

snapped into place. Insert the battery into the case and

reinstall the end cap and screws.

Fig. 3

Fig. 4

V4.0 Digital Angle Finder 8662330

Visit www.princessauto.com for more information 7

CLEANING

Clean debris and dust from the tool with a soft, moist cloth. Do not use cleaning

solvents or excessive water as either may damage the tool.

STORAGE

Remove the battery if the tool will not be used for a period of time. The battery

may corrode or discharge during storage and damage the tool.

DISPOSAL

Recycle a tool damaged beyond repair at the appropriate facility.

Contact your local municipality for a list of disposal facilities or by-laws for

electronic devices, batteries, oil or other toxic liquids.

TROUBLESHOOTING

Visit a Princess Auto Ltd. location for a solution if the tool does not function

properly or parts are missing. If unable to do so, have a qualified technician

service the tool.

8662330 Digital Angle Finder V4.0

8 For technical questions call 1-800-665-8685

V 4,0 8662330

Vous devez lire et comprendre toutes les instructions avant d'utiliser l'appareil.

Conservez ce manuel afin de pouvoir le consulter plus tard.

Manuel d'utilisateur

Détecteurd’angle

numérique

8662330 Détecteur d’angle numérique V 4,0

2 En cas de questions techniques, appelez le 1-800-665-8685

SPÉCIFICATIONS

Longueur 380 mm (15 po)

Mesure de précision pour les angles +/- 0,5 °

Affichage DÉL Écran

Fioles Numéro 2

Précision 0,5 mm/m

Pile 9 V (non compris)

Température de fonctionnement 0

℃

à 50

℃

Température d'entreposage 20

℃

à 85

℃

Arrêt automatique Environ 5 minutes

SÉCURITÉ

AVERTISSEMENT ! Veuillez lire et comprendre toutes les instructions avant

d'utiliser cet outil. L'utilisateur doit respecter les précautions de base

lorsqu'il utilise cet outil afin de réduire le risque de blessure ou de

dommage à l'équipement.

Conservez ce manuel qui contient les avertissements de sécurité, les

précautions, les instructions de fonctionnement ou d'inspection et d'entretien.

DÉFINITIONS DE DANGER

Veuillez-vous familiariser avec les avis de danger qui sont présentés dans ce

manuel. Un avis est une alerte indiquant qu'il existe un risque de dommage à la

propriété, de blessure ou de décès si on ne respecte pas certaines instructions.

DANGER ! Cet avis indique un risque immédiat et particulier qui

entraînera des blessures corporelles graves ou même la

mort si on omet de prendre les précautions nécessaires.

Détecteurd’angle

numérique

Table des matières

Langues :

Autres manuels Power Fist Outils

Power Fist

Power Fist 8623159 Manuel utilisateur

Power Fist

Power Fist 8549024 Manuel utilisateur

Power Fist

Power Fist 1/2 in. Air Ratchet and Socket Set Manuel utilisateur

Power Fist

Power Fist 8536773 Manuel utilisateur

Power Fist

Power Fist 8957425 Manuel utilisateur

Power Fist

Power Fist 8685042 Manuel utilisateur

Power Fist

Power Fist 9011438 Manuel utilisateur

Power Fist

Power Fist 9004391 Manuel utilisateur

Power Fist

Power Fist 8887408 Manuel utilisateur

Power Fist

Power Fist 8663783 Manuel utilisateur

Power Fist

Power Fist 8823494 Manuel utilisateur

Power Fist

Power Fist 8308231 Manuel utilisateur

Power Fist

Power Fist Air Hammer Manuel utilisateur

Power Fist

Power Fist 8916793 Manuel utilisateur

Power Fist

Power Fist Air Line Delivery Kit Manuel utilisateur

Power Fist

Power Fist 8655888 Manuel utilisateur

Power Fist

Power Fist 8089591 Manuel utilisateur

Power Fist

Power Fist 8063927 Manuel utilisateur

Power Fist

Power Fist 8880940 Manuel utilisateur

Power Fist

Power Fist 8814436 Manuel utilisateur

Power Fist

Power Fist 8517393 Manuel utilisateur

Power Fist

Power Fist 8843773 Manuel utilisateur

Power Fist

Power Fist 8536609 Manuel utilisateur

Power Fist

Power Fist 8012660 Manuel utilisateur

Manuels Outils populaires d'autres marques

Martor

Martor SECUNORM 175 Manuel utilisateur

ERKCO

ERKCO 1000 Manuel utilisateur

jbc

jbc N4473 Manuel utilisateur

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuel utilisateur

Worx Professional

Worx Professional Sonicrafter WU676 Manuel utilisateur

Gage Bilt

Gage Bilt GB713SH Manuel utilisateur

Hilti

Hilti DX 9-ENP Manuel utilisateur

norbar

norbar NORTRONIC 34399 Manuel utilisateur

BGS technic

BGS technic 8578 Manuel utilisateur

Makita

Makita DHR241 Manuel utilisateur

Motor Guard

Motor Guard JMB-1250 Manuel utilisateur

Power Adhesives

Power Adhesives 805-12 Manuel utilisateur

Clemco

Clemco 24189 Manuel utilisateur

VVG

VVG VNG 903 Series Manuel utilisateur

Hilti

Hilti FX 3-A Manuel utilisateur

Grizzly

Grizzly H6472 Manuel utilisateur

axing

axing BWZ 5-02 Manuel utilisateur

Dh-Robotics

Dh-Robotics RGI-100 Comment utiliser