Power Fist 8655888 Manuel utilisateur

V4.0 8655888

Please read and understand all instructions before use. Retain this manual for

future reference.

User Manual

FenderRollerTool

8655888 Fender Roller Tool V4.0

2 For technical questions call 1-800-665-8685

INTRODUCTION

The Fender Roller Tool smooths out the inner wheel well of the fender. The

telescopic cantilever’s length is adjustable and can swivel in a 180º arc to work

on a wide range of vehicles.

SAFETY

WARNING! Read and understand all instructions before using this tool. The

operator must follow basic precautions to reduce the risk of personal injury

and/or damage to the equipment.

Keep this manual for safety warnings, precautions, operating or inspection and

maintenance instructions.

HAZARD DEFINITIONS

Please familiarize yourself with the hazard notices found in this manual. A notice

is an alert that there is a possibility of property damage, injury or death if certain

instructions are not followed.

DANGER! This notice indicates an immediate and specific hazard that will

result in severe personal injury or death if the proper precautions

are not taken.

WARNING! This notice indicates a specific hazard or unsafe practice that

could result in severe personal injury or death if the proper

precautions are not taken.

CAUTION! This notice indicates a potentially hazardous situation that may result

in minor or moderate injury if proper practices are not taken.

NOTICE! This notice indicates that a specific hazard or unsafe practice will

result in equipment or property damage, but not personal injury.

FenderRollerTool

V4.0 Fender Roller Tool 8655888

Visit www.princessauto.com for more information 3

WORK AREA

1. Operate in a safe work environment. Keep your work area clean, well-lit

and free of distractions.

2. Keep anyone not wearing the appropriate safety equipment away from the

work area.

3. Store unused tools properly in a safe and dry location to prevent rust or

damage. Lock tools away and keep out of the reach of children.

PERSONAL SAFETY

WARNING! Wear personal protective equipment approved by the Canadian

Standards Association (CSA) or American National Standards Institute (ANSI).

PERSONAL PROTECTIVE EQUIPMENT

1. Always wear impact safety goggles that provide front and side protection

for the eyes. Eye protection equipment should comply with CSA Z94.3-07

or ANSI Z87.1 standards based on the type of work performed.

2. Wear the appropriate type of full-face shield in addition to safety googles,

as the work can create chips, abrasive or particulate matter.

3. Wear gloves that provide protection based on the work materials or to

reduce the effects of tool vibration.

4. Wear protective clothing designed for the work environment and tool.

5. Non-skid footwear is recommended to maintain footing and balance in the

work environment.

PERSONAL PRECAUTIONS

Control the tool, personal movement and the work environment to avoid

personal injury or damage to tool.

1. Do not operate any tool when tired or under the influence of drugs, alcohol

or medications.

2. Avoid wearing clothes or jewelry that can become entangled with the

moving parts of a tool. Keep long hair covered or bound.

3. Do not overreach when operating a tool. Proper footing and balance

enables better control in unexpected situations.

8655888 Fender Roller Tool V4.0

4 For technical questions call 1-800-665-8685

SPECIFIC SAFETY PRECAUTIONS

WARNING! DO NOT let comfort or familiarity with product (gained from

repeated use) replace strict adherence to the tool safety rules. If you use

this tool unsafely or incorrectly, you can suffer serious personal injury.

1. Use the correct tool for the job. This tool was designed for a specific

function. Do not modify or alter this tool or use it for an unintended purpose.

UNPACKING

WARNING! Do not operate the tool if any part is missing. Replace the

missing part before operating. Failure to do so could result in a malfunction

and personal injury.

Remove the parts and accessories from the packaging and inspect for damage.

Make sure that all items in the parts list are included.

Contents:

• Fender Roller Tool

IDENTIFICATION KEY

A Flange Roller

B Tommy Screw

C Telescopic

Cantilever

D Conical Washers

E Sliding Handle

F Hand Wheel

G 2-Direction

Cantilever

Adjustment

V4.0 Fender Roller Tool 8655888

Visit www.princessauto.com for more information 5

OPERATION

Letter references in parenthesis (A) refer to the included Identification Key.

The fender roller tool fits onto a 4 or 5-hole wheel hub. The diameter of the

tool’s holes range from 90 to 120 mm and fits most vehicle hubs.

1. Lift the vehicle up with a hoist or wheel jack. Place the vehicle on jack

stands if using a jack.

a. Consult the manuals for the jack, jack stands, hoist and vehicle for

safety instructions.

2. Remove the wheel and set aside. Keep the wheel lugs on hand.

3. Rotate the telescopic cantilever (C) to one side, until it cannot move any

farther. Position the tool over the wheel’s bolts so the arm’s 180º rotation

will cover the work area of the fender.

4. Place the conical washers on each bolt. Screw the wheel lugs onto the

bolts and tighten to secure the tool in place (Fig. 1 and 2).

5. Loosen the tommy screw (B) holding the flange roller (A) (Fig. 3).

6. Adjust the telescopic cantilever (C) by turning the handle (E). This will

adjust the cantilever’s position until it is the correct length (Fig. 4).

7. Secure the cantilever in place with the hand wheel (F).

Fig. 1 Fig. 2

Fig. 3 Fig. 4

8655888 Fender Roller Tool V4.0

6 For technical questions call 1-800-665-8685

8. Align the flange roller (A) to the work

surface’s curve, then lightly secure the flange

by tightening the tommy screw (B) (Fig. 5).

9. Move the tool through its arc to smooth the

fender surface (Fig. 6 and 7). Check the

flange roller’s tension after moving the

cantilever either left or right. Realign the

flange roller if necessary.

Do not tighten the tommy screw too tightly as

the flange roller can distort the fender if it

cannot self-adjust during use.

10. Clean and dry the inner surface of the fender

before applying a seam sealant to prevent

corrosion.

11. The fender is ready for painting.

CARE & MAINTENANCE

1. Maintain the tool with care. A tool in good

condition is efficient, easier to control and will

have fewer problems.

2. Inspect the tool components periodically.

Repair or replace damaged or worn components. Only use identical

replacement parts when servicing.

3. Keep the tool handles clean, dry and free from oil/grease at all times.

4. Maintain the tool’s labels and name plates. These carry important information.

If unreadable or missing, contact Princess Auto Ltd. for replacements.

WARNING! Only qualified service personnel should repair the tool. An

improperly repaired tool may present a hazard to the user and/or others.

TROUBLESHOOTING

Visit a Princess Auto Ltd. location for a solution if the tool does not function

properly or parts are missing. If unable to do so, have a qualified technician

service the tool.

Fig. 5

Fig. 6

Fig. 7

V4.0 Fender Roller Tool 8655888

Visit www.princessauto.com for more information 7

8655888 Fender Roller Tool V4.0

8 For technical questions call 1-800-665-8685

V 4,0 8655888

Vous devez lire et comprendre toutes les instructions avant d'utiliser l'appareil.

Conservez ce manuel afin de pouvoir le consulter plus tard.

Manuel d'utilisateur

Outilàrouleaupour

garde-boue

8655888 Outil à rouleau pour garde-boue V 4,0

2 En cas de questions techniques, appelez le 1-800-665-8685

INTRODUCTION

L’outil à rouleau pour aile aplanit le passage de roue intérieur de l’aile. La

longueur du porte-à-faux télescopique est ajustable et peut pivoter sur 180º

pour s’adapter à une large gamme de véhicules.

SÉCURITÉ

AVERTISSEMENT ! Veuillez lire et comprendre toutes les instructions avant

d'utiliser cet outil. L'utilisateur doit respecter les précautions de base

lorsqu'il utilise cet outil afin de réduire le risque de blessure ou de

dommage à l'équipement.

Conservez ce manuel qui contient les avertissements de sécurité, les

précautions, les instructions de fonctionnement ou d'inspection et d'entretien.

DÉFINITIONS DE DANGER

Veuillez-vous familiariser avec les avis de danger qui sont présentés dans ce

manuel. Un avis est une alerte indiquant qu'il existe un risque de dommage à la

propriété, de blessure ou de décès si on ne respecte pas certaines instructions.

DANGER ! Cet avis indique un risque immédiat et particulier qui

entraînera des blessures corporelles graves ou même la

mort si on omet de prendre les précautions nécessaires.

AVERTISSEMENT ! Cet avis indique un risque particulier ou une pratique non

sécuritaire qui pourrait entraîner des blessures

corporelles graves ou même la mort si on omet de

prendre les précautions nécessaires.

ATTENTION ! Cet avis indique une situation possiblement dangereuse qui

peut entraîner des blessures mineures ou modérées si on

ne procède pas de la façon recommandée.

Outilàrouleaupour

garde-boue

Table des matières

Langues :

Autres manuels Power Fist Outils

Power Fist

Power Fist 8916793 Manuel utilisateur

Power Fist

Power Fist 8668402 Manuel utilisateur

Power Fist

Power Fist 8814436 Manuel utilisateur

Power Fist

Power Fist Air Line Delivery Kit Manuel utilisateur

Power Fist

Power Fist 8887408 Manuel utilisateur

Power Fist

Power Fist 8536609 Manuel utilisateur

Power Fist

Power Fist 8517393 Manuel utilisateur

Power Fist

Power Fist 8662330 Manuel utilisateur

Power Fist

Power Fist 8012660 Manuel utilisateur

Power Fist

Power Fist 8843583 Manuel utilisateur

Power Fist

Power Fist 8957425 Manuel utilisateur

Power Fist

Power Fist 8603094 Manuel utilisateur

Power Fist

Power Fist 8549024 Manuel utilisateur

Power Fist

Power Fist 8843617 Manuel utilisateur

Power Fist

Power Fist 9166695 Manuel utilisateur

Power Fist

Power Fist 8880940 Manuel utilisateur

Power Fist

Power Fist 8536773 Manuel utilisateur

Power Fist

Power Fist 8089591 Manuel utilisateur

Power Fist

Power Fist 8663783 Manuel utilisateur

Power Fist

Power Fist 9151051 Manuel utilisateur

Power Fist

Power Fist 8873358 Manuel utilisateur

Power Fist

Power Fist 8505547 Manuel utilisateur

Power Fist

Power Fist 8843799 Manuel utilisateur

Power Fist

Power Fist 1/2 in. Air Ratchet and Socket Set Manuel utilisateur

Manuels Outils populaires d'autres marques

Martor

Martor SECUNORM 175 Manuel utilisateur

ERKCO

ERKCO 1000 Manuel utilisateur

jbc

jbc N4473 Manuel utilisateur

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuel utilisateur

Worx Professional

Worx Professional Sonicrafter WU676 Manuel utilisateur

Gage Bilt

Gage Bilt GB713SH Manuel utilisateur

Hilti

Hilti DX 9-ENP Manuel utilisateur

norbar

norbar NORTRONIC 34399 Manuel utilisateur

BGS technic

BGS technic 8578 Manuel utilisateur

Makita

Makita DHR241 Manuel utilisateur

Motor Guard

Motor Guard JMB-1250 Manuel utilisateur

Power Adhesives

Power Adhesives 805-12 Manuel utilisateur

Clemco

Clemco 24189 Manuel utilisateur

VVG

VVG VNG 903 Series Manuel utilisateur

Hilti

Hilti FX 3-A Manuel utilisateur

Grizzly

Grizzly H6472 Manuel utilisateur

axing

axing BWZ 5-02 Manuel utilisateur

Dh-Robotics

Dh-Robotics RGI-100 Comment utiliser