Power Fist 8885642 Manuel utilisateur

V1.0 8885642

Please read and understand all instructions before use. Retain this manual for

future reference.

8885642 Brake Caliper Wind-Back Tool Kit V1.0

2 For technical questions call 1-800-665-8685

SPECIFICATIONS

Number of Pieces 18

Fits See Appendix A

Overall Length 6.7 in.

Material Carbon Steel

Handle Type Sliding T-handle

Handle Material Carbon Steel

Finish Sandblast

HAZARD DEFINITIONS

Please familiarize yourself with the hazard notices found in this manual. A

notice is an alert that there is a possibility of property damage, injury or

death if certain instructions are not followed.

DANGER! This notice indicates an immediate and specific hazard that

will result in severe personal injury or death if the proper

precautions are not taken.

WARNING! This notice indicates a specific hazard or unsafe practice that

could result in severe personal injury or death if the proper

precautions are not taken.

CAUTION! This notice indicates a potentially hazardous situation that may

result in minor or moderate injury if proper practices are not

taken.

NOTICE! This notice indicates that a specific hazard or unsafe practice

will result in equipment or property damage, but not personal

injury.

V1.0 Brake Caliper Wind-Back Tool Kit 8885642

Visit www.princessauto.com for more information 3

INTRODUCTION

The Brake Caliper Wind-Back Tool Kit has 14 adapters to reset the brake

caliper for a variety of vehicle models. The set comes with two wind-back

tools and spreaders to work on two calipers at once.

SAFETY

WARNING! Read and understand all instructions before using this tool. The

operator must follow basic precautions to reduce the risk of personal injury

and/or damage to the equipment.

Keep this manual for safety warnings, precautions, operating or inspection

and maintenance instructions.

WORK AREA

1. Operate in a safe work environment. Keep your work area clean, well-

lit and free of distractions. Place lights so you are not working in a

shadow.

2. Keep anyone not wearing the appropriate safety equipment away from

the work area.

3. Store unused tools properly in a safe and dry location to prevent rust

or damage. Lock tools away and keep out of the reach of children.

PERSONAL SAFETY

WARNING! Wear personal protective equipment approved by the Canadian

Standards Association (CSA) or American National Standards Institute (ANSI).

PERSONAL PROTECTIVE EQUIPMENT

1. Always wear impact safety goggles that provide front and side

protection for the eyes. Eye protection equipment should comply with

CSA Z94.3-07 or ANSI Z87.1 standards based on the type of work

performed.

2. Wear gloves that provide protection based on the work materials or to

reduce the effects of tool vibration.

3. Wear protective clothing designed for the work environment and tool.

4. Non-skid footwear is recommended to maintain footing and balance in

the work environment.

5. Wear steel toe footwear or steel toe caps to prevent a foot injury from

falling objects.

8885642 Brake Caliper Wind-Back Tool Kit V1.0

4 For technical questions call 1-800-665-8685

PERSONAL PRECAUTIONS

Control the tool, personal movement and the work environment to avoid

personal injury or damage to tool.

1. Do not operate any tool when tired or under the influence of drugs,

alcohol or medications.

2. Avoid wearing clothes or jewelry that can become entangled with the

moving parts of a tool. Keep long hair covered or bound.

3. Do not overreach when operating a tool. Proper footing and balance

enables better control in unexpected situations.

SPECIFIC SAFETY PRECAUTIONS

WARNING! DO NOT let comfort or familiarity with product (gained from

repeated use) replace strict adherence to the tool safety rules. If you use

this tool unsafely or incorrectly, you can suffer serious personal injury.

1. Use the correct tool for the job. This tool was designed for a specific

function. Do not modify or alter this tool or use it for an unintended

purpose.

2. Do not use the tool if any parts are damage broken or misplaced. Repair

or replace the parts.

3. Make sure a raised vehicle is supported with axle stands and wheel

chocks. Set the vehicle’s parking brake. Check the owner’s manual on the

correct gear for a manual vehicle.

4. Ensure the hydraulic brake system is not under pressure before cracking

the bleed screw.

UNPACKING

WARNING! Do not operate the tool if any part is missing. Replace the

missing part before operating. Failure to do so could result in a malfunction

and personal injury.

Remove the parts and accessories from the packaging and inspect for damage.

Make sure that all items in the Identification Key are included.

Contents: • Adapter Plates (15) • Wind-Back Tool (2) • Disc Pad Spreader (1)

V1.0 Brake Caliper Wind-Back Tool Kit 8885642

Visit www.princessauto.com for more information 5

IDENTIFICATION KEY

A Handle

B Bolt

C Tightening Screw Cap

D Adapter

E Pins

F Disc Pad Spreader

G Wind-Back Tool

H Adapter Plates

ASSEMBLY & INSTALLATION

Letter references in parenthesis (A) refer to the included Identification Key.

1. Pull the handle (A) fully to one side.

2. Maneuver the disc pad spreader’s (F) opening over the handle and

move the spreader to the bolt (B).

3. Maneuver the spreader over the bolt and slide it down to rest on the

tightening screw cap’s (C) raised lip.

4. Select the appropriate adapter plate (H) (see Appendix A).

5 Align the wind-back tool’s pins (E) with the adapter plate holes and

affix the plate to the tool.

OPERATION

Consult the vehicle owner’s manual or the parts service manual for

instructions on installation and maintenance of the brake caliper system.

1. Align the adapter plate’s pins with the openings on the vehicle’s caliper

piston and seat the plate.

2. Slide the disk pad spreader back until it rests against the caliper’s

forks. Rotate the tightening screw cap clockwise by hand to secure the

spreader so it does not slip. Finish tightening with a wrench.

3. Open the brake’s bleeder screw enough to let trapped air escape.

4. Turn the handle clockwise to force the piston to rotate inward.

Continue to apply pressure until the piston no longer moves. Visually

confirm it is seated and not jammed. A jammed piston may require

replacement.

5. Close the brake’s bleeder screw.

Fig.

8885642 Brake Caliper Wind-Back Tool Kit V1.0

6 For technical questions call 1-800-665-8685

CARE & MAINTENANCE

1. Maintain the tool with care. A tool in good condition is efficient, easier

to control and will have fewer problems.

2. Inspect the tool components periodically. Repair or replace damaged or

worn components. Only use identical replacement parts when servicing.

3. Follow instructions for lubricating and changing accessories.

4. Only use accessories intended for use with this tool.

5. Keep the tool clean, dry and free from oil/grease at all times.

6. Maintain the tool’s labels and name plates. These carry important

information. If unreadable or missing, contact Princess Auto Ltd. for

replacements.

WARNING! Only qualified service personnel should repair the tool. An

improperly repaired tool may present a hazard to the user and/or others.

LUBRICATION

Inspect and lubricate the tool when required. Only use light oil to lubricate

the tool. Other lubricants may not be suitable and could damage the tool or

cause a malfunction during use.

When not in use for an extended period, apply a thin coat of lubricant to the

steel parts to avoid rust. Remove the lubricant before using the tool again.

DISPOSAL

Recycle a tool damaged beyond repair at the appropriate facility.

TROUBLESHOOTING

Visit a Princess Auto Ltd. location for a solution if the tool does not function

properly or parts are missing. If unable to do so, have a qualified technician

service the tool.

V1.0 Brake Caliper Wind-Back Tool Kit 8885642

Visit www.princessauto.com for more information 7

APPENDIX A

VEHICLE ADAPTER LIST

ADAPTER #0

General Motors

Cadillac Seville and Eldorado

ADAPTER #1

Retaining plate

ADAPTER #2

Citroen XM, Xantia and other

ADAPTER #3

Alfa Romeo

Audi

Austin

BMW 318 iS, 320 i, 325 TD, 518 i, 525 i,

740 i, 850 ci, M5

Ford Fiesta

Honda Concerto

Jaguar XJ6 and XJ40

Mercedes-Benz 190, 200, 300, 420 and

560

Mitsubishi Colt

Nissan Micra, Stanza, Sunny and

Range Rover

Toyota Camry

VW Passat and Golf GTI

Volvo

ADAPTER #4

Alfa Romeo 164 2.0

Fiat

Ford Telstar and Laser

General Motors Saturn, Grand Prix

and Lumina

Honda Prelude and CRX

Mazda

Saab 9000

Subaru

ADAPTER #5 WITH 3/8 "SQUARE

DRIVE

ADAPTER #6

Nissan Primera

VW Golf 4

ADAPTER #7

Audi 80, 90, 100, V8 and coupe

Ford Sierra ABS, Granada (1985) and

Scorpio (1985)

Honda Prelude

Nissan Silvia 1.8 Turbo, Blue Bird and

Primera 2.0 I, LS, GS, GSX

Rover 8000

Saab 9000

Subaru L and Z

Peugeot 405 1 .9Gi, Gri, Sri, GTXI, MI16

and 605 2.0 Sri

Toyota Celica, Corolla GT, MR2 and GTI

16V

8885642 Brake Caliper Wind-Back Tool Kit V1.0

8 For technical questions call 1-800-665-8685

ADAPTER #8

General Motors

ADAPTER #9

General Motors

Cadillac Seville

Eldorado

ADAPTER A

Renault R21 and Laguna

ADAPTER E

Cefrio Nissan and Maxima

ADAPTER F

Opel Corsa, Astra, Zafira and Vectra

ADAPTER K

Citroen C3 and C5

ADAPTER M

Ford

ADAPTER N

Renault

Saab

Honda

V1.0 8885642

Please read and understand all instructions before use. Retain this manual for

future reference.

8885642 Trousse d'outils de rappel d'étrier de frein V1.0

2 For technical questions call 1-800-665-8685

SPÉCIFICATIONS

Nombre de pièces 18

Convient See Appendices A

Longueur hors tout (po) 6,7 po

Matériau Acier au carbone

Type de manche Poignée en T coulissante

Matériau de manche Acier au carbone

Finition Sablage au jet

DÉFINITIONS DE DANGER

Veuillez-vous familiariser avec les avis de danger qui sont présentés dans ce

manuel. Un avis est une alerte indiquant quil existe un risque de dommage

à la propriété, de blessure ou de décès si on ne respecte pas certaines

instructions.

DANGER ! Cet avis indique un risque immédiat et particulier qui

entraînera des blessures corporelles graves ou même la

mort si on omet de prendre les précautions nécessaires.

AVERTISSEMENT ! Cet avis indique un risque particulier ou une pratique non

sécuritaire qui pourrait entraîner des blessures

corporelles graves ou même la mort si on omet de

prendre les précautions nécessaires.

ATTENTION ! Cet avis indique une situation possiblement dangereuse qui

peut entraîner des blessures mineures ou modérées si on

ne procède pas de la façon recommandée.

AVIS ! Cet avis indique un risque particulier ou une pratique non

sécuritaire qui entraînera des dommages au niveau de

léquipement ou des biens, mais non des blessures

corporelles.

Table des matières

Langues :

Autres manuels Power Fist Outils

Power Fist

Power Fist 9011438 Manuel utilisateur

Power Fist

Power Fist 8843617 Manuel utilisateur

Power Fist

Power Fist 8549024 Manuel utilisateur

Power Fist

Power Fist 8916793 Manuel utilisateur

Power Fist

Power Fist 8668402 Manuel utilisateur

Power Fist

Power Fist 8873358 Manuel utilisateur

Power Fist

Power Fist 9081415 Manuel utilisateur

Power Fist

Power Fist 8823494 Manuel utilisateur

Power Fist

Power Fist Air Hammer Manuel utilisateur

Power Fist

Power Fist 8505547 Manuel utilisateur

Power Fist

Power Fist 8655888 Manuel utilisateur

Power Fist

Power Fist 8887408 Manuel utilisateur

Power Fist

Power Fist 8308231 Manuel utilisateur

Power Fist

Power Fist 8814436 Manuel utilisateur

Power Fist

Power Fist 8063927 Manuel utilisateur

Power Fist

Power Fist 9166695 Manuel utilisateur

Power Fist

Power Fist 1/2 in. Air Ratchet and Socket Set Manuel utilisateur

Power Fist

Power Fist 8662330 Manuel utilisateur

Power Fist

Power Fist 8536773 Manuel utilisateur

Power Fist

Power Fist 8517393 Manuel utilisateur

Power Fist

Power Fist 8012660 Manuel utilisateur

Power Fist

Power Fist 9151051 Manuel utilisateur

Power Fist

Power Fist 8843799 Manuel utilisateur

Power Fist

Power Fist 8438806 Manuel utilisateur

Manuels Outils populaires d'autres marques

Martor

Martor SECUNORM 175 Manuel utilisateur

ERKCO

ERKCO 1000 Manuel utilisateur

jbc

jbc N4473 Manuel utilisateur

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuel utilisateur

Worx Professional

Worx Professional Sonicrafter WU676 Manuel utilisateur

Gage Bilt

Gage Bilt GB713SH Manuel utilisateur

Hilti

Hilti DX 9-ENP Manuel utilisateur

norbar

norbar NORTRONIC 34399 Manuel utilisateur

BGS technic

BGS technic 8578 Manuel utilisateur

Makita

Makita DHR241 Manuel utilisateur

Motor Guard

Motor Guard JMB-1250 Manuel utilisateur

Power Adhesives

Power Adhesives 805-12 Manuel utilisateur

Clemco

Clemco 24189 Manuel utilisateur

VVG

VVG VNG 903 Series Manuel utilisateur

Hilti

Hilti FX 3-A Manuel utilisateur

Grizzly

Grizzly H6472 Manuel utilisateur

axing

axing BWZ 5-02 Manuel utilisateur

Dh-Robotics

Dh-Robotics RGI-100 Comment utiliser