Planet WNAP-7200 Manuel utilisateur

802.11a/n Wireless LAN Outdoor CPE AP/Router

WNAP-7200

Quick Installation Guide

Table of Contents

1. Package Content.......................................................................................... 4

2. Hardware Installation ................................................................................... 5

3. Web Conguration ....................................................................................... 9

4. Further Conguration ..................................................................................10

Designed with the most innovative 802.11a/n technology, WNAP-7200 provides

maximum 150Mbps high data rate for outdoor environment. There are multiple

operating modes supported in WNAP-7200: Bridge, Gateway, WISP, and built-

in 18dBi at panel antenna and high transmit output power make WNAP-7200 a

suitable CPE solution for widely open space applications such as WISP, campuses,

and airports. Except for 64/128-bit WEP encryption, WNAP-7200 integrates WPA,

WPA2 and 802.1x authentication to secure the information of your wireless LAN.

1. Package Content

WNAP-7200 x 1

PoE Injector x 1

Power Adapter x 1

Mounting Kit x 1

CD x 1

Quick Installation Guide x 1

Note

If any of the above items are missing or damaged, contact your

local dealer for support.

2. Hardware Installation

Before you proceed with the installation, it is necessary that you have enough

information about WNAP-7200.

1. Please connect right installation “PoE” port of PoE inject to WNAP-7200; “LAN”

port of PoE injector to LAN PC, wrong installation will cause the device damage.

Note

Strongly suggest using SFTP cable, for better protection of the data

wire. 25-meter SFTP cable also available by order, the part no is

CB-STP-25. Please contact with local dealer for more information.

2. Using Category 3 or higher UTP or STP cable, connect the “LAN” port of PoE

Injector to a 10Mbps or 10/100Mbps Ethernet hub or switch, and connect the PC

on the same LAN for management.

3. Locate an optimum location and use the provided Mounting kit to tie the WNAP-

7200 to a pole.

Note

1. To avoid thunder strike, consider installing ELA-100, thunder

arrester toward the CPE AP and the PoE injector.

2. For secured reason, while install the CPE AP, please be aware for

the electric wires around, and tighten the pole. Without tighten

the CPE AP, the pole and the installed site is with electric wire

around, there could be danger of being hurt by falling or lethal

injury.

4. Connect the 12V 1.25A DC power adapter to the PoE Injector socket, and plug it

into an AC outlet to power on the WNAP-7200.

Note

1. The PoE Injector is a passive device. It will inject the DC power

into the UTP cable right away once you connect the DC-plug in to

the DC-jack of the PoE Injector.

2. DONOT connect the PoE Injector labeled as POE port to any

devices but WNAP-7200, otherwise it will damage the device

permanently.

5. For Ethernet port application, please refer to user’s manual for bridge, gateway

and WISP application for the rst installation, LAN port is suggested.

Note

1. ONLY use the power adapter supplied with the WNAP-7200.

Otherwise, the product may be damaged.

2. Strongly suggest using STP cable whether the cable exposed

outdoor for waterproof and avoiding thunder stroke.

OUTDOOR INSTALLATION WARNING

IMPORTANT SAFETY PRECAUTIONS:

LIVES MAY BE AT RISK! Carefully observe these instructions and any special

instructions that are included with the equipment you are installing.

CONTACTING POWER LINES CAN BE LETHAL.

Make sure no power lines are

anywhere where possible contact

can be made. Antennas, masts,

towers, guy wires or cables may

lean or fall and contact these limes.

People may be injured or killed if

they are touching or holding any

part of equipment when it contacts

electric lines. Make sure there is

NO possibility that equipment or

personnel can come in contact

directly or indirectly with power lines.

Assume all overhead lines are power lines.

The horizontal distance from a tower, mast or antenna to the nearest power line

should be at least twice the total length of the mast/antenna combination. This will

ensure that the mast will not contact power if it falls either during installation or

later.

TO AVOID FALLING, USE SAFE PROCEDURES WHEN WORKING

AT HEIGHTS ABOVE GROUND.

Select equipment locations that will allow safe, simple equipment installation.

Don’t work alone. A friend or co-worker can save your life if an accident

happens.

Use approved non-conducting lasers and other safety equipment. Make sure all

equipment is in good repair.

If a tower or mast begins falling, don’t attempt to catch it. Stand back and let it

fall.

If anything such as a wire or mast does come in contact with a power line,

DON’T TOUCH IT OR ATTEMPT TO MOVE IT. Instead, save your life by

calling the power company.

Don’t attempt to erect antennas or towers on windy days.

MAKE SURE ALL TOWERS AND MASTS ARE SECURELY

GROUNDED, AND ELECTRICAL CABLES CONNECTED TO

ANTENNAS HAVE LIGHTNING ARRESTORS.

This will help prevent re damage or human injury in case of lightning, static build-

up, or short circuit within equipment connected to the antenna.

The base of the antenna mast or tower must be connected directly to the

building protective ground or to one or more approved grounding rods, using 1

OAWG ground wire and corrosion-resistant connectors.

Refer to the National Electrical Code for grounding details.

IF A PERSON COMES IN CONTACT WITH ELECTRICAL POWER,

AND CANNOT MOVE:

DON’T TOUCH THAT PERSON, OR YOU MAY BE ELECTROCUTED.

Use a non-conductive dry board, stick or rope to push or drag them so they no

longer are in contact with electrical power.

Once they are no longer contacting electrical power, administer CPR if you are

certied, and make sure that emergency medical aid has been requested.

3. Web Conguration

WNAP-7200 provides a user friendly interface for users to congure via web

browser. Please follow the below steps to congure WNAP-7200 basic settings.

1. It will take around 40 seconds to complete the boot up sequence after power on

from PoE.

2. Open your web browser and type default IP address of WNAP-7200

(http://192.168.0.1) into the “Address Field” of you web browser. Before

conguration, please make sure your PC’s IP address is under the same IP range

with WNAP-7200, such as 192.168.0.x.

3. After entering, ll the default username/password (admin / admin) and then

you can see the home page.

4. Further Conguration

For more settings of WNAP-7200, please refer to the user’s manual in the CD.

If you have any difculty on resolving the problem while installing or using the

device, please feel free to contact your local dealer or PLANET Technical Support.

Autres manuels pour WNAP-7200

Table des matières

Autres manuels Planet Routeur réseau

Planet

Planet EPN-102 Manuel utilisateur

Planet

Planet WGSW-404 Manuel utilisateur

Planet

Planet FNSW-2400PS Manuel utilisateur

Planet

Planet IGS-620TF Manuel utilisateur

Planet

Planet GS-5220-48T4X Manuel utilisateur

Planet

Planet GRT-101 Manuel utilisateur

Planet

Planet PL-802 Manuel utilisateur

Planet

Planet IVR-100 Series Manuel utilisateur

Planet

Planet Enterprise WiFi System Manuel utilisateur

Planet

Planet GS-4210 SERIES Manuel utilisateur

Planet

Planet GSW-1600HP Manuel utilisateur

Planet

Planet SG-4800 Manuel utilisateur

Planet

Planet ADE-3110 Manuel utilisateur

Planet

Planet ISW-621 Series Manuel utilisateur

Planet

Planet FNSW-4800 Manuel utilisateur

Planet

Planet IGS-5227-6T Manuel utilisateur

Planet

Planet WNRT-320GS Manuel utilisateur

Planet

Planet ADSL 2/2+ VPN Firewall Router ADW-4302A v2 Manuel utilisateur

Planet

Planet WRT-403 Manuel utilisateur

Planet

Planet WDRT-1202AC Manuel utilisateur

Planet

Planet SG-4800 Manuel utilisateur

Planet

Planet WAP-500N Manuel utilisateur

Planet

Planet GSD-800S Manuel utilisateur

Planet

Planet ADE-3100 Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité