Planet PL-802 Manuel utilisateur

– 6 – – 7 –

Step 2: To secure your powerline network:

1. Press and hold the Security button of PL-802 for 10

seconds. Then all the LEDs are off and restart. The

original network encryption setting is cleared.

2. Repeat 1 to clear another powerline’s original network

encryption setting.

3. Press the Security buttons of both powerlines for 1 to

3 seconds.

4. The power LED of both powerlines starts to blink

and try to communicate with their private network

encryption.

Note: The operation timeout is 120 seconds.

5. After the successful setup, the Power LED will

remain solid and the Powerline LED will start

blinking.

Push

Button

Within 2 minutes

Step 3: 1. Connect the Ethernet port of PL-802 to your home

router, switch or ADSL modem’s Ethernet port via the

RJ45 cable.

2. Connect the Ethernet port of the PL-802 to the

computer via the RJ45 cable.

Linked

Internet

Laptop

6. Utility Installation for Windows

PLANET Power Packet Utility is a software utility used to search and

make connecting on a powerline network quick and simple.

The installation procedure for the Powe Packet Utility will vary

depending on which operating system you are using on your computer.

The following procedure is for installation under Windows 7. Installation

of other operating systems is similar.

Step 1: Download the Power Packet Utility from PLANET download

URL

http://www.planet.com.tw/en/support/download.

php?view=8184&key=PL-802#list

Step 2: The le you have downloaded is a zip le. Unzip it and

double-click on the “Setup.exe” executable le to begin

installation.

Step 3: The utility will be installed on your computer and

a new icon “Power Packet Utility” will appear

on your desktop.

Power Packet

Utility

Note

This utility is only for Windows 2000, 2003, XP, Vista,

Windows 7, Windows 8 and Windows 10.

Further Information:

The above steps introduce the simple installations of the PL-802. For

further details on the installation of the powerline, please refer to the

user manual which can be downloaded from the PLANET website.

http://www.planet.com.tw/en/support/download.

php?view=3&key=PL-802#list

If you have further questions, please contact the local dealer or

distributor where you purchased this product or you can contact PLANET

directly at the following email address: support@planet.com.tw

– 5 –

– 1 –

– 3 –

– 2 –

– 4 –

3. Physical Introduction

Port & Button Descriptions

Security Button

10/100BASE-TX

Ethernet RJ-45 Port

Button Description

Security

Reset: Hold the Security button down for 10 seconds to

reset to default setting. All of the LED lights will

go out 1 second and then light up again.

Pair: Press the Security button for 1~3 seconds to join

another powerline network. The power LED will ash

to search another powerline.

1. Package Contents

Thank you for choosing PLANET 600M AV2 Powerline Ethernet Bridge,

PL-802/PL-802-KIT. Open the box of the PL-802/PL-802-KIT carefully and

unpack it. The box should contain the following items:

PL-802

(Twin pack x 2) Quick Install Guide Ethernet Cable

(Twin pack x 2)

Note

If there is any item missing or damaged, please contact

the seller immediately.

2. Installation Precautions

Do not plug this powerline adapter into a powerstrip that has surge

protection. Doing so will degrade powerline performance. For best

performance, plug all powerline adapters directly into a wall outlet.

Good Performance Weak Performance

A maximum of 16 powerline adapters can be networked.

LED Descriptions

Ethernet LED

Power LED

Powerline LED

LED Denition

LED Status Description

Power

Green Steady on to indicate the PL-802 is connected to

the power outlet.

Blinking Standby mode.

Off Power off.

Powerline

Off This powerline adapter is not connected.

Green The quality of signal is excellent with optimal

network.

Orange The quality of signal is normal with standard

network.

Red The quality of signal is weak which causes slower

network.

Blinking

Green

The PL-802 is actively sending or receiving data

with another powerline.

Ethernet

Green Ethernet Link detected

Blinking The PL-802 is actively sending or receiving data

over the Ethernet port.

Off Ethernet Link not active.

Note

The Power LED indicator will blink in standby mode.

It will automatically get into standby mode, if the

Ethernet-link is lost for 60 seconds. If you unplug the

Ethernet cable, it will get into standby mode after 60

seconds. Under standby mode, Powerline and

Ethernet LEDs will both be off.

4. Hardware Installation

To create a powerline network, simply connect the PL-802 and the

Powerline Ethernet Bridge to AC wall power outlets that are on the

same electrical system. No additional conguration in the powerline

network is necessary.

Follow the steps below to install the PL-802 in the house.

Step 1: 1. Plug the Powerline Ethernet Bridge into AC wall

power outlets near the device you want to connect.

2. Plug the PL-802 into AC wall power outlet in your room

or ofce where you want to install.

3. Ensure the Power LEDs are on.

Plug

– 1 –

– 3 –

– 2 –

– 4 –

3. Physical Introduction

Port & Button Descriptions

Security Button

10/100BASE-TX

Ethernet RJ-45 Port

Button Description

Security

Reset: Hold the Security button down for 10 seconds to

reset to default setting. All of the LED lights will

go out 1 second and then light up again.

Pair: Press the Security button for 1~3 seconds to join

another powerline network. The power LED will ash

to search another powerline.

1. Package Contents

Thank you for choosing PLANET 600M AV2 Powerline Ethernet Bridge,

PL-802/PL-802-KIT. Open the box of the PL-802/PL-802-KIT carefully and

unpack it. The box should contain the following items:

PL-802

(Twin pack x 2) Quick Install Guide Ethernet Cable

(Twin pack x 2)

Note

If there is any item missing or damaged, please contact

the seller immediately.

2. Installation Precautions

Do not plug this powerline adapter into a powerstrip that has surge

protection. Doing so will degrade powerline performance. For best

performance, plug all powerline adapters directly into a wall outlet.

Good Performance Weak Performance

A maximum of 16 powerline adapters can be networked.

LED Descriptions

Ethernet LED

Power LED

Powerline LED

LED Denition

LED Status Description

Power

Green Steady on to indicate the PL-802 is connected to

the power outlet.

Blinking Standby mode.

Off Power off.

Powerline

Off This powerline adapter is not connected.

Green The quality of signal is excellent with optimal

network.

Orange The quality of signal is normal with standard

network.

Red The quality of signal is weak which causes slower

network.

Blinking

Green

The PL-802 is actively sending or receiving data

with another powerline.

Ethernet

Green Ethernet Link detected

Blinking The PL-802 is actively sending or receiving data

over the Ethernet port.

Off Ethernet Link not active.

Note

The Power LED indicator will blink in standby mode.

It will automatically get into standby mode, if the

Ethernet-link is lost for 60 seconds. If you unplug the

Ethernet cable, it will get into standby mode after 60

seconds. Under standby mode, Powerline and

Ethernet LEDs will both be off.

4. Hardware Installation

To create a powerline network, simply connect the PL-802 and the

Powerline Ethernet Bridge to AC wall power outlets that are on the

same electrical system. No additional conguration in the powerline

network is necessary.

Follow the steps below to install the PL-802 in the house.

Step 1: 1. Plug the Powerline Ethernet Bridge into AC wall

power outlets near the device you want to connect.

2. Plug the PL-802 into AC wall power outlet in your room

or ofce where you want to install.

3. Ensure the Power LEDs are on.

Plug

– 1 –

– 3 –

– 2 –

– 4 –

3. Physical Introduction

Port & Button Descriptions

Security Button

10/100BASE-TX

Ethernet RJ-45 Port

Button Description

Security

Reset: Hold the Security button down for 10 seconds to

reset to default setting. All of the LED lights will

go out 1 second and then light up again.

Pair: Press the Security button for 1~3 seconds to join

another powerline network. The power LED will ash

to search another powerline.

1. Package Contents

Thank you for choosing PLANET 600M AV2 Powerline Ethernet Bridge,

PL-802/PL-802-KIT. Open the box of the PL-802/PL-802-KIT carefully and

unpack it. The box should contain the following items:

PL-802

(Twin pack x 2) Quick Install Guide Ethernet Cable

(Twin pack x 2)

Note

If there is any item missing or damaged, please contact

the seller immediately.

2. Installation Precautions

Do not plug this powerline adapter into a powerstrip that has surge

protection. Doing so will degrade powerline performance. For best

performance, plug all powerline adapters directly into a wall outlet.

Good Performance Weak Performance

A maximum of 16 powerline adapters can be networked.

LED Descriptions

Ethernet LED

Power LED

Powerline LED

LED Denition

LED Status Description

Power

Green Steady on to indicate the PL-802 is connected to

the power outlet.

Blinking Standby mode.

Off Power off.

Powerline

Off This powerline adapter is not connected.

Green The quality of signal is excellent with optimal

network.

Orange The quality of signal is normal with standard

network.

Red The quality of signal is weak which causes slower

network.

Blinking

Green

The PL-802 is actively sending or receiving data

with another powerline.

Ethernet

Green Ethernet Link detected

Blinking The PL-802 is actively sending or receiving data

over the Ethernet port.

Off Ethernet Link not active.

Note

The Power LED indicator will blink in standby mode.

It will automatically get into standby mode, if the

Ethernet-link is lost for 60 seconds. If you unplug the

Ethernet cable, it will get into standby mode after 60

seconds. Under standby mode, Powerline and

Ethernet LEDs will both be off.

4. Hardware Installation

To create a powerline network, simply connect the PL-802 and the

Powerline Ethernet Bridge to AC wall power outlets that are on the

same electrical system. No additional conguration in the powerline

network is necessary.

Follow the steps below to install the PL-802 in the house.

Step 1: 1. Plug the Powerline Ethernet Bridge into AC wall

power outlets near the device you want to connect.

2. Plug the PL-802 into AC wall power outlet in your room

or ofce where you want to install.

3. Ensure the Power LEDs are on.

Plug

– 1 –

– 3 –

– 2 –

– 4 –

3. Physical Introduction

Port & Button Descriptions

Security Button

10/100BASE-TX

Ethernet RJ-45 Port

Button Description

Security

Reset: Hold the Security button down for 10 seconds to

reset to default setting. All of the LED lights will

go out 1 second and then light up again.

Pair: Press the Security button for 1~3 seconds to join

another powerline network. The power LED will ash

to search another powerline.

1. Package Contents

Thank you for choosing PLANET 600M AV2 Powerline Ethernet Bridge,

PL-802/PL-802-KIT. Open the box of the PL-802/PL-802-KIT carefully and

unpack it. The box should contain the following items:

PL-802

(Twin pack x 2) Quick Install Guide Ethernet Cable

(Twin pack x 2)

Note

If there is any item missing or damaged, please contact

the seller immediately.

2. Installation Precautions

Do not plug this powerline adapter into a powerstrip that has surge

protection. Doing so will degrade powerline performance. For best

performance, plug all powerline adapters directly into a wall outlet.

Good Performance Weak Performance

A maximum of 16 powerline adapters can be networked.

LED Descriptions

Ethernet LED

Power LED

Powerline LED

LED Denition

LED Status Description

Power

Green Steady on to indicate the PL-802 is connected to

the power outlet.

Blinking Standby mode.

Off Power off.

Powerline

Off This powerline adapter is not connected.

Green The quality of signal is excellent with optimal

network.

Orange The quality of signal is normal with standard

network.

Red The quality of signal is weak which causes slower

network.

Blinking

Green

The PL-802 is actively sending or receiving data

with another powerline.

Ethernet

Green Ethernet Link detected

Blinking The PL-802 is actively sending or receiving data

over the Ethernet port.

Off Ethernet Link not active.

Note

The Power LED indicator will blink in standby mode.

It will automatically get into standby mode, if the

Ethernet-link is lost for 60 seconds. If you unplug the

Ethernet cable, it will get into standby mode after 60

seconds. Under standby mode, Powerline and

Ethernet LEDs will both be off.

4. Hardware Installation

To create a powerline network, simply connect the PL-802 and the

Powerline Ethernet Bridge to AC wall power outlets that are on the

same electrical system. No additional conguration in the powerline

network is necessary.

Follow the steps below to install the PL-802 in the house.

Step 1: 1. Plug the Powerline Ethernet Bridge into AC wall

power outlets near the device you want to connect.

2. Plug the PL-802 into AC wall power outlet in your room

or ofce where you want to install.

3. Ensure the Power LEDs are on.

Plug

– 6 – – 7 –

Step 2: To secure your powerline network:

1. Press and hold the Security button of PL-802 for 10

seconds. Then all the LEDs are off and restart. The

original network encryption setting is cleared.

2. Repeat 1 to clear another powerline’s original network

encryption setting.

3. Press the Security buttons of both powerlines for 1 to

3 seconds.

4. The power LED of both powerlines starts to blink

and try to communicate with their private network

encryption.

Note: The operation timeout is 120 seconds.

5. After the successful setup, the Power LED will

remain solid and the Powerline LED will start

blinking.

Push

Button

Within 2 minutes

Step 3: 1. Connect the Ethernet port of PL-802 to your home

router, switch or ADSL modem’s Ethernet port via the

RJ45 cable.

2. Connect the Ethernet port of the PL-802 to the

computer via the RJ45 cable.

Linked

Internet

Laptop

6. Utility Installation for Windows

PLANET Power Packet Utility is a software utility used to search and

make connecting on a powerline network quick and simple.

The installation procedure for the Powe Packet Utility will vary

depending on which operating system you are using on your computer.

The following procedure is for installation under Windows 7. Installation

of other operating systems is similar.

Step 1: Download the Power Packet Utility from PLANET download

URL

http://www.planet.com.tw/en/support/download.

php?view=8184&key=PL-802#list

Step 2: The le you have downloaded is a zip le. Unzip it and

double-click on the “Setup.exe” executable le to begin

installation.

Step 3: The utility will be installed on your computer and

a new icon “Power Packet Utility” will appear

on your desktop.

Power Packet

Utility

Note

This utility is only for Windows 2000, 2003, XP, Vista,

Windows 7, Windows 8 and Windows 10.

Further Information:

The above steps introduce the simple installations of the PL-802. For

further details on the installation of the powerline, please refer to the

user manual which can be downloaded from the PLANET website.

http://www.planet.com.tw/en/support/download.

php?view=3&key=PL-802#list

If you have further questions, please contact the local dealer or

distributor where you purchased this product or you can contact PLANET

directly at the following email address: support@planet.com.tw

– 5 –

– 6 – – 7 –

Step 2: To secure your powerline network:

1. Press and hold the Security button of PL-802 for 10

seconds. Then all the LEDs are off and restart. The

original network encryption setting is cleared.

2. Repeat 1 to clear another powerline’s original network

encryption setting.

3. Press the Security buttons of both powerlines for 1 to

3 seconds.

4. The power LED of both powerlines starts to blink

and try to communicate with their private network

encryption.

Note: The operation timeout is 120 seconds.

5. After the successful setup, the Power LED will

remain solid and the Powerline LED will start

blinking.

Push

Button

Within 2 minutes

Step 3: 1. Connect the Ethernet port of PL-802 to your home

router, switch or ADSL modem’s Ethernet port via the

RJ45 cable.

2. Connect the Ethernet port of the PL-802 to the

computer via the RJ45 cable.

Linked

Internet

Laptop

6. Utility Installation for Windows

PLANET Power Packet Utility is a software utility used to search and

make connecting on a powerline network quick and simple.

The installation procedure for the Powe Packet Utility will vary

depending on which operating system you are using on your computer.

The following procedure is for installation under Windows 7. Installation

of other operating systems is similar.

Step 1: Download the Power Packet Utility from PLANET download

URL

http://www.planet.com.tw/en/support/download.

php?view=8184&key=PL-802#list

Step 2: The le you have downloaded is a zip le. Unzip it and

double-click on the “Setup.exe” executable le to begin

installation.

Step 3: The utility will be installed on your computer and

a new icon “Power Packet Utility” will appear

on your desktop.

Power Packet

Utility

Note

This utility is only for Windows 2000, 2003, XP, Vista,

Windows 7, Windows 8 and Windows 10.

Further Information:

The above steps introduce the simple installations of the PL-802. For

further details on the installation of the powerline, please refer to the

user manual which can be downloaded from the PLANET website.

http://www.planet.com.tw/en/support/download.

php?view=3&key=PL-802#list

If you have further questions, please contact the local dealer or

distributor where you purchased this product or you can contact PLANET

directly at the following email address: support@planet.com.tw

– 5 –

– 6 – – 7 –

Step 2: To secure your powerline network:

1. Press and hold the Security button of PL-802 for 10

seconds. Then all the LEDs are off and restart. The

original network encryption setting is cleared.

2. Repeat 1 to clear another powerline’s original network

encryption setting.

3. Press the Security buttons of both powerlines for 1 to

3 seconds.

4. The power LED of both powerlines starts to blink

and try to communicate with their private network

encryption.

Note: The operation timeout is 120 seconds.

5. After the successful setup, the Power LED will

remain solid and the Powerline LED will start

blinking.

Push

Button

Within 2 minutes

Step 3: 1. Connect the Ethernet port of PL-802 to your home

router, switch or ADSL modem’s Ethernet port via the

RJ45 cable.

2. Connect the Ethernet port of the PL-802 to the

computer via the RJ45 cable.

Linked

Internet

Laptop

6. Utility Installation for Windows

PLANET Power Packet Utility is a software utility used to search and

make connecting on a powerline network quick and simple.

The installation procedure for the Powe Packet Utility will vary

depending on which operating system you are using on your computer.

The following procedure is for installation under Windows 7. Installation

of other operating systems is similar.

Step 1: Download the Power Packet Utility from PLANET download

URL

http://www.planet.com.tw/en/support/download.

php?view=8184&key=PL-802#list

Step 2: The le you have downloaded is a zip le. Unzip it and

double-click on the “Setup.exe” executable le to begin

installation.

Step 3: The utility will be installed on your computer and

a new icon “Power Packet Utility” will appear

on your desktop.

Power Packet

Utility

Note

This utility is only for Windows 2000, 2003, XP, Vista,

Windows 7, Windows 8 and Windows 10.

Further Information:

The above steps introduce the simple installations of the PL-802. For

further details on the installation of the powerline, please refer to the

user manual which can be downloaded from the PLANET website.

http://www.planet.com.tw/en/support/download.

php?view=3&key=PL-802#list

If you have further questions, please contact the local dealer or

distributor where you purchased this product or you can contact PLANET

directly at the following email address: [email protected]

– 5 –

Autres manuels pour PL-802

Table des matières

Autres manuels Planet Routeur réseau

Planet

Planet FRT-420SN Manuel utilisateur

Planet

Planet WDRT-1800AX Manuel utilisateur

Planet

Planet 85M Powerline Ethernet PL-201-KIT Manuel utilisateur

Planet

Planet SOHOConnect Series Manuel utilisateur

Planet

Planet WNRT-625G Manuel utilisateur

Planet

Planet GRT-402 Manuel utilisateur

Planet

Planet ADE-4100 Manuel utilisateur

Planet

Planet XRT-401B Manuel utilisateur

Planet

Planet VRT-402N Manuel utilisateur

Planet

Planet PL-510W Manuel utilisateur

Planet

Planet ADE-3100 Manuel utilisateur

Planet

Planet AND-4102 Manuel utilisateur

Planet

Planet FGSW-1820RS Manuel utilisateur

Planet

Planet VR-300 Series Manuel utilisateur

Planet

Planet ADE-3400 Manuel utilisateur

Planet

Planet IGS-4215-16T2S Manuel utilisateur

Planet

Planet MH-3400 Manuel utilisateur

Planet

Planet GSW-1600S Manuel utilisateur

Planet

Planet ADW-4301A/B Manuel utilisateur

Planet

Planet MGSW SERIES Manuel utilisateur

Planet

Planet RT-101 Manuel utilisateur

Planet

Planet ADE-3400 Manuel utilisateur

Planet

Planet XRT-401C Manuel utilisateur

Planet

Planet WSD-800 Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité