Planet FGSW-1820RS Manuel utilisateur
Trademarks
Copyright © PLANET Technology Corp. 2006.
Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trade-
marks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in
all environments and applications, and makes no warranty and representa-
tion, either implied or expressed, with respect to the quality, performance,
merchantability, or fitness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate;
PLANET disclaims liability for any inaccuracies or omissions that may have
occurred.
Information in this User’s Manual is subject to change without notice and does
not represent a commitment on the part of PLANET. PLANET assumes no re-
sponsibility for any inaccuracies that may be contained in this User’s Manual.
PLANET makes no commitment to update or keep current the information
in this User’s Manual, and reserves the right to make improvements to this
User’s Manual and/or to the products described in this User’s Manual, at any
time without notice.
If you find information in this manual that is incorrect, misleading, or incom-
plete, we would appreciate your comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment gen-
erates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the Instruction manual, may cause harmful interfer-
ence to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures.
WEEE Warning
To avoid the potential effects on the environment and human health as
a result of the presence of hazardous substances in electrical and elec-
tronic equipment, end users of electrical and electronic equipment should
understand the meaning of the crossed-out wheeled bin symbol. Do not
dispose of WEEE as unsorted municipal waste and have to collect such
WEEE separately.
Revision
PLANET 16/24-Port 10/100Mbps+ 2 Gigabit TP / SFP combo Ethernet Smart
Switch User’s Manual
FOR MODEL: FGSW-1820RS
FGSW-2620RS
Rev: 1.0(July.2006)
Part No: 2010-A81120-000
Table of Contents
1. INTRODUCTION 1
1.1 PACKAGE CONTENTS 1
1.2 HOW TO USE THIS MANUAL 1
1.3 PRODUCT FEATURES 2
1.4 PRODUCT SPECIFICATIONS 3
2. INSTALLATION 5
2.1 PRODUCT DESCRIPTION 5
2.2 INSTALLING A FGSW-1820RS/FGSW-2620RS 7
3. CONSOLE CONFIGURATION 10
3.1 PREPARING FOR CONFIGURATION 10
3.2 GETTING STARTED 12
4. SWITCH OPERATION 29
4.1 ADDRESS TABLE 29
4.2 LEARNING 29
4.3 FORWARDING & FILTERING 29
4.4 STORE-AND-FORWARD 29
4.5 AUTO-NEGOTIATION 30
5. TROUBLESHOOTING 30
APPENDIX A NETWORKING CONNECTION 31
A.1 SWITCH‘S RJ-45 PIN ASSIGNMENTS 31
A.2 RJ-45 CABLE PIN ASSIGNMENTS 32
This page is intentionally left blank
1
Chapter 1
Introduction
1.1 Package Contents
Check the contents of your package for following parts:
● 16/24-Port 10/100Mbps+ 2 Gigabit TP / SFP combo Ethernet Smart Switch x1
● User’s manual x1
● RS-232 cable x1
● Power cord x1
● Two Rack-Mounting Brackets with Attachment Screws x1
If any of these are missing or damaged, please contact your dealer immediately, if
possible, retain the carton including the original packing material, and use them against
to repack the product in case there is a need return to it to us for repairing.
1.2 How to Use This Manual
This 16/24-Port 10/100Mbps +2 Gigabit TP / SFP combo Ethernet Smart Switch Users’
Manual is structured as follows:
● Section 2, Installation
It explains the functions of FGSW-1820RS/FGSW-2620RS and how to physi-
cally install the FGSW-1820RS/FGSW-2620RS.
● Section 3, Console Configuration
It contains information about the smart function from the console interface of
FGSW-1820RS/FGSW-2620RS.
● Section 4 Switch operation
It explains the Switch operation of FGSW-1820RS / FGSW-2620RS.
● Section 5 Troubleshooting
It contains troubleshooting guide of FGSW-1820RS / FGSW-2620RS.
● Appendix A
It contains cable information of FGSW-1820RS/FGSW-2620RS.
In the following section, unless specified, the term “Switch” means the two
Switches, i.e. FGSW-1820RS or FGSW-2620RS; term of “switch” can be any
third part switches.
2
1.3 Product Features
● Comply with the IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3z Gigabit
Ethernet standard
● 16/24-Port 10/100Mbps Fast Ethernet Switch
● 2 10/100/1000Mbps ports and 2 SFP interfaces
● Each Switching ports support auto-negotiation-10/20, 100/200Mbps support-
ed
● Auto-MDI/MDI-X detection on each RJ-45 port
● Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x PAUSE
frame flow control (full-duplex)
● High performance Store and Forward architecture, broadcast storm control,
runt/CRC filtering eliminates erroneous packets to optimize the network band-
width
● 8K MAC address table, automatic source address learning and ageing
● 2.5Mbit embedded memory for packet buffers
● Console interface for Switch basic management and setup
● Support up to 26 port-based VLAN groups
● Support up to 6/8 Trunk groups, each trunk for up to maximum 4 port with
800Mbps bandwidth
● Support QoS and bandwidth control on each port
● Support IGMP Snooping
● EMI standards comply with FCC, CE class A
3
1.4 Product Specifications
Product
FGSW-1820RS / FGSW-2620RS
16/24-Port 10/100Mbps + 2 Gigabit TP / SFP combo
Ethernet Smart Switch
Hardware Specification
Ports 16/24 10/100Base-TX RJ-45 Auto-MDI/MDI-X
ports
Gigabit ports 2 10/100/1000Mbps ports and 2 SFP interfaces
Switch Processing
Scheme Store-and-forward
Throughput (packet per
second)
FGSW-1820RS: 5.35Mpps.
FGSW-2620RS: 6.54Mpps
Switch fabric 8.8Gbps
Address Table 8K entries
Share data Buffer 2.5Mbit
Flow Control Back pressure for half duplex, IEEE 802.3x Pause
Frame for full duplex
Dimensions 440 x 120 x 44 mm (1U height)
Weight FGSW-1820RS:1.46 kg
FGSW-2620RS:1.57 kg
Power Requirement 100~240 VAC, 50-60 Hz
Power Consumption /
Dissipation
FGSW-1820RS: 13.2 watts / 45BTU
FGSW-2620RS: 23.1 watts / 78BTU
Temperature Operating: 0~50 degree C
Storage -40~70 degree
Humidity Operating: 5% to 90%, Storage: 5% to 90% (Noncondensing)
Smart function
System Configuration Console interface
Port configuration
Port disable/enable. Auto-negotiation 10/100Mbps
full and half duplex mode selection. Flow control
disable / enable. Bandwidth control on each port
Port Status
Display each port’s speed duplex mode, link status,
Flow control status. Auto negotiation status, trunk
status.
4
VLAN 26 port-based VLAN groups
Port trunking Support 6 / 8 groups of 4-Port trunk support
QoS Allow to assign high priority on each port
IGMP Snooping Allow to disable or enable.
Standards Conformance
Regulation Compliance FCC Part 15 Class A, CE
Standards Compliance
IEEE 802.3 (Ethernet)
IEEE 802.3u (Fast Ethernet),
IEEE 802.3x (full-duplex flow control)
IEEE 802.1p QoS
5
Chapter 2
Installation
This section describes the functionalities of the Switch components and guides how to
install it on the desktop or shelf. Basic knowledge of networking is assumed. Please read
this chapter completely before continuing.
2.1 Product Description
The PLANET Switch provides 16/24 10/100Mbps Fast Ethernet ports with 2 10/100/1000Mbps
ports and 2-SFP interfaces (port #17/25, port#18/26), either TP or SFP per port. The two
Gigabit ports either can be 1000Base-T for 10/100/1000Mbps or 1000Base-SX/LX through
SFP (Small Factor Pluggable) interface. The distance can be extended from 100 meters
(TP), 550 meters (Multi-mode fiber), up to above 10/50/70/120 kilometers (Single-mode
fiber). The Switch with non-blocking backplane and simplifies the task of upgrading your
LAN to cater for increased bandwidth demand.
Equipped with console, the Ethernet Smart Switch can be programmed for basic Switch
management functions such as port speed configuration, Port Trunking, VLAN, QoS,
bandwidth control and IGMP Snooping.
2.1.1 Product Overview
PLANET FGSW-1820RS/FGSW-2620RS, the Switch is Ethernet Smart Switch with 16/24
RJ-45 10/100Mbps ports. The Switch also provides up to two 10/100/1000Mbps ports
and 2-SFP interfaces for cost effective high-performance network connectivity. With its
8.8Gbps non-blocking switch fabric, the PLANET Switch can also provide a local, high band-
width, Fast Ethernet network for your departmental backbone plus the ability to trunk four
ports (800Mbps) to enable switch-to-switch backbone. The advanced functionality of the
Switch eliminates traditional problems associated with the use of Ethernet. Users can be
segregated using built-in VLAN functionality. These, coupled with the flexible fiber module
options, make the Switch one of the best and most cost-effective MTU switch solutions for
Multi-tenant service providers.
This Switch also supports store-and-forward forwarding scheme to ensure low latency
and high data integrity, eliminates unnecessary traffic and relieves congestion on critical
network paths. With an intelligent address recognition algorithm, Switch could recognize
up to 8K different MAC address and enables filtering and forwarding at full wire speed.
2.1.2 The Front Panel
Figure 2-1 shows front panel of FGSW-1820RS.
Figure 2-1 PLANET FGSW-1820RS Front Panel
6
Figure 2-2 shows front panel of FGSW-2620RS.
Figure 2-2 PLANET FGSW-2620RS Front Panel
2.1.3 LED Indicators
System
LED Color Function
PWR Green Lit: Power on
Per 10/100Mbps port
LED Color Function
LNK/ACT Green
Lit: indicate the link through that port is successfully es-
tablished.
Blink: indicate that the switch is actively sending or receiv-
ing data over that port.
100 Orange Lit: indicate that the port is operating at 100Mbps.
Off: indicate that the port is operating at 10Mbps.
Per 10/100/1000Base-T port /SFP interfaces
LED Color Function
LNK/ACT
1000 Green
Lit: indicate that the port is operating at 1000Mbps.
Off: indicate that the port is operating at 10Mbps or
100Mbps.
Blink: indicate that the switch is actively sending or receiv-
ing data over that port.
LNK/ACT
100 Green
Lit: indicate that the port is operating at 100Mbps.
Off: indicate that the port is operating at 10Mbps or
1000Mbps.
Blink: indicate that the switch is actively sending or receiv-
ing data over that port.
FDX Green
Lit: indicate that the port is operating at full-duplex mode.
Off: indicate that the port is operating at half-duplex
mode.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Planet Routeur réseau
Planet
Planet GSW-2416 Manuel utilisateur
Planet
Planet VIP-320 Manuel utilisateur
Planet
Planet WNRT-617 Manuel utilisateur
Planet
Planet WDRT-1202AC Manuel utilisateur
Planet
Planet EH-2400 Manuel utilisateur
Planet
Planet WGR-500 Manuel de l'opérateur
Planet
Planet ADW-4301A/B Manuel utilisateur
Planet
Planet GS-4210-24P2S Manuel utilisateur
Planet
Planet GSW-1600S Manuel utilisateur
Planet
Planet EPN-102 Manuel utilisateur
Planet
Planet XRT-401F Manuel utilisateur
Planet
Planet ADSL 2/2+ VPN Firewall Router ADW-4302A v2 Manuel utilisateur
Planet
Planet 85M Powerline Ethernet PL-201-KIT Manuel utilisateur
Planet
Planet FGSW-4840S Manuel utilisateur
Planet
Planet GRT-402 Manuel utilisateur
Planet
Planet ADE-3400 Manuel utilisateur
Planet
Planet SGS-5220-24P2X Manuel utilisateur
Planet
Planet GRT-101 Manuel utilisateur
Planet
Planet GSD-908HP Manuel utilisateur
Planet
Planet GSW-1602SF Manuel utilisateur
Manuels Routeur réseau populaires d'autres marques
NETGEAR
NETGEAR FS526T - Switch Manuel utilisateur
Korenix
Korenix JetNet 5710G Series Manuel utilisateur
Automated Logic
Automated Logic ZN551 Manuel du propriétaire
Cisco
Cisco ASR 1000 Series Manuel de l'opérateur
EnGenius
EnGenius ESR-9710 Manuel utilisateur
Cisco
Cisco 805 Series Instructions d'utilisation et de sécurité